This document provides information about front suspension components and alignment specifications for a vehicle. It describes the front suspension system which uses upper and lower control arms, coil springs, shock absorbers, and a stabilizer bar. It provides instructions for inspecting, diagnosing, and adjusting components like wheel bearings, ball joints, and toe alignment. Specifications are given for caster, camber, toe alignment, and torque values for fasteners.
Sanjay Nagar Call Girls: 🍓 7737669865 🍓 High Profile Model Escorts | Bangalor...
Exj 2
1. XJ SUSPENSION 2-1
SUSPENSION
CONTENTS
page page
ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 REAR SUSPENSION . . . . . . . . . . . . . . . . . . . . . 13
FRONT SUSPENSION . . . . . . . . . . . . . . . . . . . . . 6
ALIGNMENT
INDEX
page page
GENERAL INFORMATION SERVICE PROCEDURES
WHEEL ALIGNMENT . . . . . . . . . . . . . . . . . . . . . 1 PRE-ALIGNMENT INSPECTION . . . . . . . . . . . . . 2
DIAGNOSIS AND TESTING WHEEL ALIGNMENT . . . . . . . . . . . . . . . . . . . . . 2
SUSPENSION AND STEERING SYSTEM . . . . . . 2 SPECIFICATIONS
ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
GENERAL INFORMATION • WHEEL TOE POSITION is the difference
between the leading inside edges and trailing inside
WHEEL ALIGNMENT edges of the front tires. Incorrect wheel toe position
Wheel alignment involves the correct positioning of is the most common cause of unstable steering and
the wheels in relation to the vehicle. The positioning uneven tire wear. The wheel toe position is the final
is accomplished through suspension and steering front wheel alignment adjustment.
linkage adjustments. An alignment is considered • STEERING AXIS INCLINATION ANGLE is
essential for efficient steering, good directional stabil- measured in degrees and is the angle that the steer-
ity and to minimize tire wear. The most important ing knuckles are tilted. The inclination angle has a
measurements of an alignment are caster, camber fixed relationship with the camber angle. It will not
and toe position (Fig. 1). change except when a spindle or ball stud is dam-
• CASTER is the forward or rearward tilt of the aged or bent. The angle is not adjustable, the dam-
steering knuckle from vertical. Tilting the top of the aged component(s) must be replaced to correct mis-
knuckle rearward provides positive caster. Tilting the alignment.
top of the knuckle forward provides negative caster. • THRUST ANGLE is the angle of the rear axle
Caster is a directional stability angle. This angle relative to the centerline of the vehicle. Incorrect
enables the front wheels to return to a straight thrust angle can cause off-center steering and exces-
ahead position after turns. sive tire wear. This angle is not adjustable, the dam-
• CAMBER is the inward or outward tilt of the aged component(s) must be replaced to correct mis-
wheel relative to the center of the vehicle. Tilting the alignment.
top of the wheel inward provides negative camber.
Tilting the top of the wheel outward provides positive CAUTION: Do not attempt to modify any suspen-
camber. Incorrect camber will cause wear on the sion or steering component by heating and bend-
inside or outside edge of the tire. The angle is not ing.
adjustable, the damaged component(s) must be
replaced to correct mis-alignment.
2. VEHICLE OF CAMBER (NOT SHOWN)(−)TOP AXLE
AXLE CASTER REAR
ANGLERELATIVE TO
TRUE TICAL
POSITIVE CENTER-
VER- LINE
TRUST CAMBER TERLINE OF
ANGLE WHEELOUTBOARD
WHEELSCRUBRIGHT
CENTER-CEN-
PIVOTLINE RADIUS
NEGATIVE CAM-
BER ANGLE
POINTS IN) FRONT B >
POSITIVE OF A
(TOE OUT) TOE (TOE
NEGATIVETOE VEHICLE
B <A FRONT OF VEHICLEPIN POSITIVE CASTER
TOE A
KING
(+) AXLE POINTS VERTICAL
LEFT
2-2 SUSPENSION XJ
Fig. 1 Wheel Alignment Measurements
DIAGNOSIS AND TESTING
SUSPENSION AND STEERING SYSTEM
SERVICE PROCEDURES specifications with the vehicle at its NORMAL RIDE
HEIGHT.
PRE-ALIGNMENT INSPECTION
Before starting wheel alignment, the following CAMBER
inspection is necessary and must be completed. The wheel camber angle is preset. This angle is not
(1) Inspect tires for size, air pressure and tread adjustable and cannot be altered.
wear.
CASTER
(2) Inspect front wheel bearings for wear or adjust-
Before checking the caster of the front axle for cor-
ment.
rect angle, be sure the axle is not bent or twisted.
(3) Inspect front wheels and tires for excessive
Road test the vehicle, make left and right turns. If
radial or lateral runout and balance.
the steering wheel returns to the center position
(4) Inspect ball studs, linkage pivot points and
unassisted, the caster angle is correct. If steering
steering gear for looseness, roughness or binding.
wheel does not return toward the center position
(5) Inspect suspension components for wear and
unassisted, an incorrect caster angle is probable.
noise.
Caster can be adjusted by installing the appropri-
ate size shims (Fig. 2). Changing caster angle will
WHEEL ALIGNMENT
also change the front propeller shaft angle. The
Before each alignment reading, the vehicle should
propeller shaft angle has priority over caster.
be jounced (rear first, then front). Grasp each
Refer to Group 3 Differential & Driveline for
bumper at the center and jounce the vehicle up and
additional information.
down several times. Always release the bumper in
the down position. Set the front end alignment to
3. SUSPENSION ARM SHIM
XJ SUSPENSION 2-3
SERVICE PROCEDURES (Continued)
CONDITION POSSIBLE CAUSES CORRECTION
FRONT END 1. Loose or worn wheel bearings. 1. Adjust or replace wheel bearings.
NOISE 2. Loose or worn steering or suspension components 2. Tighten or replace components as necessary.
EXCESSIVE 1. Loose or worn wheel bearings. 1. Adjust or replace wheel bearings.
PLAY IN 2. Loose or worn steering or suspension components 2. Tighten or replace components as necessary.
STEERING 3. Loose or worn steering gear. 3. Adjust or replace steering gear.
FRONT 1. Loose or worn wheel bearings. 1. Adjust or replace wheel bearings.
WHEELS 2. Loose or worn steering or suspension components 2. Tighten or replace components as necessary.
SHIMMY 3. Tires worn or out of balance. 3. Replace or balance tires.
4. Alignment. 4. Align vehicle to specifications.
5. Leaking steering dampener. 5. Replace steering dampener.
VEHICLE 1. Loose or worn wheel bearings. 1. Adjust or replace wheel bearings.
INSTABILITY 2. Loose or worn steering or suspension components 2. Tighten or replace components as necessary.
3. Tire pressure. 3. Adjust tire pressure.
4. Alignment. 4. Align vehicle to specifications.
EXCESSIVE 1. Loose or worn steering gear. 1. Adjust or replace steering gear.
STEERING 2. Power steering fluid low. 2. Add fluid and repair leak.
EFFORT 3. Column coupler binding. 3. Replace coupler.
4. Tire pressure. 4. Adjust tire pressure.
5. Alignment. 5. Align vehicle to specifications.
VEHICLE 1. Tire pressure. 1. Adjust tire pressure.
PULLS TO 2. Alignment. 2. Align vehicle to specifications.
ONE SIDE 3. Loose or worn steering or suspension components 3. Tighten or replace components as necessary.
4. Radial tire lead. 4. Rotate or replace tire as necessary.
5. Brake pull. 5. Repair brake as necessary.
6. Weak or broken spring. 6. Replace spring.
(1) Start the engine and turn wheels both ways
before straightening the wheels. Secure the steering
wheel with the front wheels in the straight-ahead
position. Turn off the engine.
(2) Loosen the adjustment sleeve clamp bolts (Fig.
3).
(3) Adjust the right wheel toe position with the
drag link. Turn the sleeve until the right wheel is at
correct TOE-IN specifications. Position the clamp
bolts as shown (Fig. 4) and tighten to 49 N·m (36 ft.
lbs.).
NOTE: Make sure the toe setting does not change
during clamp tightening.
(4) Adjust the left wheel toe position with the tie
rod. Turn the sleeve until the left wheel is at specifi-
cations. Position the clamp bolts as shown (Fig. 4)
and tighten to 27 N·m (20 ft. lbs.).
NOTE: Make sure the toe setting does not change
Fig. 2 Caster Adjustment
during clamp tightening.
TOE POSITION (LHD)
(5) Verify the right toe setting.
NOTE: The wheel toe position adjustment should (6) Road test the vehicle on a flat level road to ver-
be the final adjustment. ify the steering wheel is centered.
4. DRAGCLAMPS
LINK DRAG LINK
PITMANARM TIE ROD CLAMP STEERING DAMPENER TIE ROD ADJUSTMENT SLEEVE
FWD
2-4 SUSPENSION XJ
SERVICE PROCEDURES (Continued)
NOTE: Once the toe setting is correct, the steering correct TOE-IN specifications. Position the clamp
wheel can be re-centered by adjusting only the drag bolts to their original position and tighten to 49 N·m
link. (36 ft. lbs.).
NOTE: Make sure the toe setting does not change
during clamp tightening.
(4) Adjust the right wheel toe position with the tie
rod. Turn the sleeve until the right wheel is at cor-
rect TOE-IN specifications. Position the clamp bolts
to their original position and tighten to 27 N·m (20
ft. lbs.).
NOTE: Make sure the toe setting does not change
during clamp tightening.
(5) Verify the right toe setting.
(6) Road test the vehicle on a flat level road to ver-
ify the steering wheel is centered.
Fig. 4 Drag Link and Tie Rod Clamp (LHD) NOTE: Once the toe setting is correct, the steering
wheel can be re-centered by adjusting only the drag
TOE POSITION (RHD)
link.
NOTE: The wheel toe position adjustment should
be the final adjustment.
(1) Start the engine and turn wheels both ways
before straightening the wheels. Secure the steering
wheel with the front wheels in the straight-ahead
position. Turn off the engine.
(2) Loosen the adjustment sleeve clamp bolts (Fig.
5).
(3) Adjust the left wheel toe position with the drag
link. Turn the sleeve until the left wheel is at the
Fig. 3 Steering Linkage (LHD)
5. STEERING MENTNER LINK
TIE ROD ADJUST-
DAMP-
SLEEVE
DRAG FWD PITMAN ARM
XJ SUSPENSION 2-5
Fig. 5 Steering Linkage (RHD)
SPECIFICATIONS
ALIGNMENT
NOTE: All alignment specifications are in degrees.
MAX RT/LT
ADJUSTMENT PREFERRED RANGE
DEFFERENCE
CASTER + 7.0° + 5.25° to + 8.5° 1.25°
CAMBER − 0.25° − 0.75° to + 0.5° 1.0°
(fixed angle)
WHEEL TOE-IN 0° − 0.10° to + 0.25° .05°
(each wheel)
6. 2-6 SUSPENSION XJ
FRONT SUSPENSION
INDEX
page page
DESCRIPTION AND OPERATION STABILIZER BAR . . . . . . . . . . . . . . . . . . . . . . . 10
SUSPENSION COMPONENTS . . . . . . . . . . . . . . 6 STEERING KNUCKLE . . . . . . . . . . . . . . . . . . . . 8
DIAGNOSIS AND TESTING TRACK BAR . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SHOCK DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . 7 UPPER SUSPENSION ARM . . . . . . . . . . . . . . . . 8
REMOVAL AND INSTALLATION WHEEL MOUNTING STUDS . . . . . . . . . . . . . . . 11
AXLE BUSHING . . . . . . . . . . . . . . . . . . . . . . . . . 9 SPECIFICATIONS
COIL SPRING/JOUNCE BUMPER . . . . . . . . . . . 7 TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . 12
HUB BEARING . . . . . . . . . . . . . . . . . . . . . . . . . 10 SPECIAL TOOLS
LOWER SUSPENSION ARM . . . . . . . . . . . . . . . 8 FRONT SUSPENSION . . . . . . . . . . . . . . . . . . . 12
SHOCK ABSORBER . . . . . . . . . . . . . . . . . . . . . 7
DESCRIPTION AND OPERATION allow for adjustment of caster and drive shaft pinion
angle. The suspension arm travel is limited through
SUSPENSION COMPONENTS the use of jounce bumpers in compression and shocks
The front suspension is a link/coil design (Fig. 1). absorbers in rebound.
This suspension is use on Left Hand Drive (LHD) Stabilizer Bar: The stabilizer bar is used to min-
and Right Hand Drive (RHD) vehicles. The suspen- imize vehicle body roll during turns. The spring steel
sion is comprised of: bar helps to control the vehicle body in relationship
• Drive axle (4WD), tube axle (2WD) to the suspension. The bar extends across the front
• Dual-action shock absorbers underside of the chassis and connects to the body
• Coil springs rails. Links are connected from the bar to the axle
• Upper and lower suspension arms brackets. Stabilizer bar mounts are isolated by rub-
• Stabilizer bar ber bushings.
• Track bar Track Bar: The track bar is used to locate the
• Jounce bumpers axle laterally. The bar is attached to a body rail
Link/Coil Suspension: This suspension allows bracket with a ball stud and isolated with a bushing
each wheel to adapt to different road surfaces with- at the axle bracket.
out greatly affecting the opposite wheel. Wheels are
attached to a hub/bearings which bolts to the knuck- CAUTION: Components attached with a nut and
les. The hub/bearing is not serviceable and is cotter pin must be torqued to specification. Then if
replaced as a unit. Steering knuckles pivot on the slot in the nut does not line up with the cotter
replaceable ball studs attached to the axle tube pin hole, tighten nut until it is aligned. Never loosen
yokes. the nut to align the cotter pin hole.
Shock Absorbers: The shocks dampen jounce and
rebound of the vehicle over various road conditions. CAUTION: Suspension components with rubber
The top of the shock absorbers are bolted to the body. bushings should be tightened with the vehicle at
The bottom of the shocks are bolted to the axle normal ride height. It is important to have the
spring bracket. springs supporting the weight of the vehicle when
Coil Springs: The springs control ride quality and the fasteners are torqued. If springs are not at their
maintain proper ride height. The coil springs mount normal ride position, vehicle ride comfort could be
up in the fender shield to a bracket which is part of affected and premature bushing wear may occur.
the unitized body. A rubber isolator is located Rubber bushings must never be lubricated.
between the top of the spring and the body. The bot-
tom of the spring seats on a axle pad and is retained
with a clip. NOTE: Periodic lubrication of the front suspension
Upper & Lower Suspension Arms: The suspen- (steering) system components is required. Refer to
sion arms are different lengths, with bushings at Group 0, Lubrication And Maintenance for the rec-
both ends. They bolt the axle assembly to the body. ommended maintenance schedule.
The lower arms use shims at the body mount to
7. LOWER SHOCK TRACKAXLE
UPPER SUSPENSION ARM
LINKS COILBUMPER
JOUNCE SPRING
STABILIZER BAR
ABSORBER
XJ SUSPENSION 2-7
DIAGNOSIS AND TESTING REMOVAL AND INSTALLATION
SHOCK DIAGNOSIS SHOCK ABSORBER
A knocking or rattling noise from a shock absorber
may be caused by movement between mounting REMOVAL
bushings and metal brackets or attaching compo- (1) Remove the nut, retainer and grommet from
nents. These noises can usually be stopped by tight- the upper stud in the engine compartment (Fig. 2).
ening the attaching nuts. If the noise persists, (2) Remove the lower nuts and bolts from the axle
inspect for damaged and worn bushings, and attach- bracket. Remove the shock absorber.
ing components. Repair as necessary if any of these
conditions exist. INSTALLATION
A squeaking noise from the shock absorber may be (1) Position the lower retainer and grommet on the
caused by the hydraulic valving and may be intermit- upper stud. Insert the shock absorber through the
tent. This condition is not repairable and the shock shock tower hole.
absorber must be replaced. (2) Install the lower bolts and nuts. Tighten nuts
The shock absorbers are not refillable or adjust- to 23 N·m (17 ft. lbs.).
able. If a malfunction occurs, the shock absorber (3) Install the upper grommet and retainer on the
must be replaced. To test a shock absorber, hold it in stud in the engine compartment. Install the nut and
an upright position and force the piston in and out of tighten to 10 N·m (8 ft. lbs.).
the cylinder four or five times. The action throughout
each stroke should be smooth and even. COIL SPRING/JOUNCE BUMPER
The shock absorber bushings do not require any
REMOVAL
type of lubrication. Do not attempt to stop bushing
(1) Raise and support the vehicle. Position a
noise by lubricating them. Grease and mineral oil-
hydraulic jack under the axle to support it.
base lubricants will deteriorate the bushing.
(2) Remove the wheel if necessary.
Fig. 1 Suspension Components (LHD)
8. SHOCK ABSORBER
CONTROL FWD
GROMMET
GROMMET
RETAINER
FRAME
ARM SPRING
RETAINER NUT SPRING SCREW
SCREW
SPRING FWD NUT
RETAINER ISOLATOR
2-8 SUSPENSION XJ
REMOVAL AND INSTALLATION (Continued)
Fig. 2 Coil Spring & Shock Absorber
(3) Mark and disconnect the front propeller shaft STEERING KNUCKLE
from the axle. For service procedures on the steering knuckle and
(4) Disconnect the lower suspension arms from the ball studs refer to Group 3 Differentials And Driv-
axle (Fig. 2). eline.
(5) Disconnect the stabilizer bar link and shock
absorber from the axle. LOWER SUSPENSION ARM
(6) Disconnect the track bar from the body rail
bracket. REMOVAL
(7) Disconnect the drag link from the pitman arm. (1) Raise and support the vehicle.
(8) Lower the axle until the spring is free from the (2) Remove the lower suspension arm nut and bolt
upper mount. Remove the coil spring clip and remove from the axle bracket.
the spring. (3) Remove the nut and bolt from the rear bracket
(9) Pull jounce bumper out of mount. and remove the lower suspension arm (Fig. 3).
INSTALLATION INSTALLATION
(1) Install jounce bumper into mount. (1) Position the lower suspension arm at the axle
(2) Position the coil spring on the axle pad. Install bracket and rear bracket.
the spring clip and bolt. Tighten bolt to 21 N·m (16 (2) Install the bolts and finger tighten the nuts.
ft. lbs.). (3) Remove support and lower the vehicle.
(3) Raise the axle into position until the spring (4) Tighten the front and rear nuts to 115 N·m (85
seats in the upper mount. ft. lbs.).
(4) Connect the stabilizer bar links and shock
absorbers to the axle bracket. Connect the track bar UPPER SUSPENSION ARM
to the body rail bracket.
(5) Install the lower suspension arms to the axle. REMOVAL
DO NOT TIGHTEN AT THIS TIME. (1) Raise and support the vehicle.
(6) Install the front propeller shaft to the axle. (2) Remove the upper suspension arm nut and bolt
(7) Remove the supports and lower the vehicle. at the axle bracket.
(8) Tighten lower suspension arms nuts to 115 (3) Remove the nut and bolt at the frame rail and
N·m (85 ft. lbs.). remove the upper suspension arm (Fig. 3).
INSTALLATION
(1) Position the upper suspension arm at the axle
and frame rail.
9. (LT-2WD)
(LT-4WD) FWD NUT
BOLT UPPER ARM
LOWER ARM NUT FRAMEBOLT
NUTBOLT RAIL
NUT (J-35581-2)TOOL
SPECIAL 7932–2
SPECIAL
7932–2 TOOL TOOL
SPECIAL 7603 7603
TOOL
(J-35581-2)
(J-21474-18)
(J-21474-18)
SPECIAL AXLE SPECIAL
BRACKETTOOL SPECIAL7932-1 7604
(J-35581-1)
7932-1 AXLE (J-21474-19)
SPECIAL TOOL
(J-35581-1)
SPECIAL 7604
(J-21474-19)
BRACKET
TOOL TOOL
XJ SUSPENSION 2-9
REMOVAL AND INSTALLATION (Continued)
Fig. 3 Upper and Lower Suspension Arms Fig. 4 Bushing Removal
(2) Install the bolts and finger tighten the nuts.
(3) Remove the supports and lower the vehicle.
(4) Tighten the nut at the axle to 75 N·m (55 ft.
lbs.). Tighten the nut at the frame bracket to 90 N·m
(66 ft. lbs.).
AXLE BUSHING
REMOVAL
(1) Remove the upper suspension arm from axle
(2) Position Receiver 7932-1 (J-35581-1) over the
bushing in the axle and install Bushing Removal/In-
staller (Fig. 4).
(3) Remove the bushing by tightening the Long
Nut.
NOTE: For two-wheel drive axles and right side on
Model 30 axle, do not remove Receiver 7932-1
(J-35581-1) at this time.
INSTALLATION
(1) Position new bushing, Receiver and Installer Fig. 5 Bushing Installation
on axle (Fig. 5).
(2) Install the bushing by tightening the Long Nut.
(3) Remove tools and install the upper suspension
arm.
10. STABILIZER
BAR RETAINER
CLAMP
GROMMET BUSHING
LINK NUT PLATE STUD SUPPORT NUTFWD
COTTERIN
P BRACKET TRACK BAR
FRAME
BRACKET
NUT LEFT
BALL FRAME
SCREW
STUD
RAIL
ENDNUT
2 - 10 SUSPENSION XJ
REMOVAL AND INSTALLATION (Continued)
STABILIZER BAR NOTE: A puller tool may be necessary to separate
the ball stud from the frame rail bracket.
REMOVAL
(1) Raise and support the vehicle. (3) Remove the bolt and flag nut from the axle
(2) Disconnect the stabilizer bar links from the shaft tube bracket (Fig. 7).
axle brackets (Fig. 6). (4) Remove the track bar.
Fig. 7 Track Bar (LHD)
Fig. 6 Stabilizer Bar (LHD)
INSTALLATION
(3) Disconnect the stabilizer bar from the links.
(1) Install the track bar at axle tube bracket.
(4) Disconnect the stabilizer bar clamps from the
Loosely install the retaining bolt and flag nut.
body rails. Remove the stabilizer bar.
(2) It may be necessary to pry the axle assembly
INSTALLATION over to install the track bar at the body rail. Install
(1) Inspect stabilizer bar bushings. Replace bush- track bar at the body rail bracket. Install the retain-
ings if cracked, cut, distorted, or worn. ing nut on the stud.
(2) Position the stabilizer bar on the body rail and (3) Remove the supports and lower the vehicle.
install the bushings and clamps. Ensure the bar is (4) Tighten the retaining bolt at the axle shaft
centered with equal spacing on both sides. Tighten tube bracket to 100 N·m (74 ft. lbs.).
the bolts to 75 N·m (40 ft. lbs.). (5) Tighten the ball stud nut to 81 N·m (60 ft.
(3) Install the links and grommets onto the stabi- lbs.). Install a new cotter pin.
lizer bar and axle brackets. Tighten the nut at the
connecting links at the axle bracket to 95 N·m (70 ft. HUB BEARING
lbs.). The Hub Bearing is serviced as an assembly.
(4) Tighten the stabilizer bar to connecting link
REMOVAL
nut to 36 N·m (27 ft. lbs.).
(1) Raise and support the vehicle.
(5) Remove the supports and lower the vehicle.
(2) Remove the wheel and tire assembly.
TRACK BAR (3) Remove the brake components from the axle,
refer to Group 5 Brakes.
REMOVAL (4) Remove the cotter pin, nut retainer and axle
(1) Raise and support the vehicle. hub nut (Fig. 8).
(2) Remove the cotter pin and nut from the ball (5) Remove the hub mounting bolts and remove
stud end at the body rail bracket. hub bearing from the steering knuckle and axle
shaft.
11. TONE WHEEL (ABS) BOLT STEERINGNUCKLE
K REMOVER ANDASSEMBLY
HUB
BRAKE SHIELD
BEARING
WHEEL STUD
WASHER
NUT COTTER PIN
RETAINER
XJ SUSPENSION 2 - 11
REMOVAL AND INSTALLATION (Continued)
Fig. 8 Hub Bearing & Knuckle
INSTALLATION
(1) Install the hub bearing and brake dust shield
to the knuckle.
(2) Install the hub to knuckle bolts and tighten to
102 N·m (75 ft. lbs.).
(3) Install the hub washer and nut. Tighten the
hub nut to 237 N·m (175 ft. lbs.). Install the nut
retainer and a new cotter pin.
(4) Install the brake components, refer to Group 5
Brakes.
(5) Install the wheel and tire assembly.
(6) Remove support and lower the vehicle.
WHEEL MOUNTING STUDS
REMOVAL
(1) Raise and support vehicle. Fig. 9 Wheel Stud Removal
(2) Remove wheel and tire assembly.
(5) Install the brake rotor and caliper, refer to
(3) Remove brake caliper and rotor, refer to Group
Group 5 Brakes for procedure.
5 Brakes for procedure.
(6) Install wheel and tire assembly, use new lug
(4) Remove stud from hub with Remover C-4150A
nut on stud or studs that were replaced.
(Fig. 9).
(7) Remove support and lower vehicle.
INSTALLATION
(1) Install new stud into hub flange.
(2) Install three washers onto stud, then install
lug nut with the flat side of the nut against the
washers.
(3) Tighten lug nut until the stud is pulled into
the hub flange. Verify that the stud is properly
seated into the flange.
(4) Remove lug nut and washers.
13. XJ SUSPENSION 2 - 13
REAR SUSPENSION
INDEX
page page
DESCRIPTION AND OPERATION LEAF SPRING . . . . . . . . . . . . . . . . . . . . . . . . . 14
SUSPENSION COMPONENT . . . . . . . . . . . . . . 13 SHOCK ABSORBER . . . . . . . . . . . . . . . . . . . . . 13
DIAGNOSIS AND TESTING STABILIZER BAR . . . . . . . . . . . . . . . . . . . . . . . 14
SPRING AND SHOCK DIAGNOSIS . . . . . . . . . . 13 SPECIFICATIONS
REMOVAL AND INSTALLATION TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . 15
LEAF SPRING AND SHACKLE BUSHING . . . . . 15
DESCRIPTION AND OPERATION DIAGNOSIS AND TESTING
SUSPENSION COMPONENT SPRING AND SHOCK DIAGNOSIS
The rear suspension is comprised of: A knocking or rattling noise from a shock absorber
• Drive Axle may be caused by movement between mounting
• Leaf Springs bushings and metal brackets or attaching compo-
• Dual-Action Shock Absorbers nents. These noises can usually be stopped by tight-
• Stabilizer Bar (optional) ening the attaching nuts. If the noise persists,
• Jounce Bumpers inspect for damaged and worn bushings, and attach-
Leaf Springs: The rear suspension system uses a ing components. Repair as necessary if any of these
multi-leaf springs and a solid drive axle. The forward conditions exist.
end of the springs are mounted to the body rail hang- A squeaking noise from the shock absorber may be
ers through rubber bushings. The rearward end of caused by the hydraulic valving and may be intermit-
the springs are attached to the body by the use of tent. This condition is not repairable and the shock
shackles. The spring and shackles use rubber bush- absorber must be replaced.
ings. The bushing help to isolate road noise. The The shock absorbers are not refillable or adjust-
shackles allow the springs to change their length as able. If a malfunction occurs, the shock absorber
the vehicle moves over various road conditions. must be replaced. To test a shock absorber, hold it in
Shock Absorbers: Ride control is accomplished an upright position and force the piston in and out of
through the use of dual-action shock absorbers. The the cylinder four or five times. The action throughout
shocks dampen the jounce and rebound as the vehicle each stroke should be smooth and even.
travels over various road conditions. The top of the The spring eye and shock absorber bushings do not
shock absorbers are bolted to the body crossmember. require any type of lubrication. Do not attempt to
The bottom of the shocks are bolted to the axle stop spring bushing noise by lubricating them.
bracket. Grease and mineral oil-base lubricants will deterio-
Stabilizer Bar: The stabilizer bar is used to min- rate the bushing rubber.
imize vehicle body roll. The spring steel bar helps to If the vehicle is used for severe, off-road operation,
control the vehicle body in relationship to the sus- the springs should be examined periodically. Check
pension. The bar extends across the underside of the for broken and shifted leafs, loose and missing clips,
vehicle and is bolted body. Links at the end of the and broken center bolts. Refer to Spring and Shock
bar are bolted to axle. Absorber Diagnosis chart for additional information.
Jounce Bumpers: The jounce bumpers are used
to limit the spring and axle travel. They are bolted to
the frame rail above the axle. REMOVAL AND INSTALLATION
CAUTION: Suspension components which use rub- SHOCK ABSORBER
ber/urethane bushings, should be tightened at vehi-
cle ride height. This will prevent premature bushing REMOVAL
failure and maintain vehicle ride comfort. (1) Remove the shock absorber upper bolts from
the body bracket (Fig. 1).
(2) Remove lower attaching nut and washer from
the bracket stud. Remove the shock absorber.
14. SHOCKABSORBER FWD
SHACKLE BUSHING SPRING U-BOLTS
BRACKET SPRING
NUTSHOCK
ABSORBERBUSHING
FWDRETAINER
NUT BUMPER BRACKET FWD
2 - 14 SUSPENSION XJ
REMOVAL AND INSTALLATION (Continued)
SPRING AND SHOCK ABSORBER DIAGNOSIS
CONDITION POSSIBLE CAUSES CORRECTION
SPRING SAGS 1. Broken leaf. 1. Replace spring.
2. Spring fatigue. 2. Replace spring.
SPRING NOISE 1. Loose spring clamp bolts. 1. Tighten to specification.
2. Worn bushings. 2. Replace spring.
3. Worn or missing spring liner. 3. Replace liner.
SHOCK NOISE 1. Loose mounting fastener. 1. Tighten to specification.
2. Worn bushings. 2. Replace shock.
3. Leaking shock. 3. Replace shock.
Fig. 1 Rear Suspension Components
INSTALLATION INSTALLATION
(1) Install the shock absorber lower eye on the (1) Position the stabilizer bar links at the spring
spring bracket stud. Install the shock absorber and brackets. Install the attaching bolts and nuts and
upper bolts on the body bracket. tighten to 74 N·m (55 ft. lbs.).
(2) Tighten the lower nut to 62 N·m (46 ft. lbs.). (2) Attach the stabilizer bar to the body rail brack-
(3) Tighten the upper bolts to 23 N·m (17 ft. lbs.). ets with the bolts. Tighten to 54 N·m (40 ft. lbs.).
(3) Remove the supports and lower the vehicle.
STABILIZER BAR
LEAF SPRING
REMOVAL
(1) Raise and support the vehicle. REMOVAL
(2) Disconnect stabilizer bar links from spring (1) Raise vehicle at body rails.
brackets (Fig. 2). (2) Remove the wheel and tire assemblies.
(3) Disconnect the stabilizer bar brackets from the (3) Support axle with hydraulic jack to relieve axle
body rails. Remove the stabilizer bar and links. weight.
15. SPRING BAR FWD
SWAY LINK
BOLT
BRACKET SCREW GROMMET
BUSHING SCREW NUT
FRAMERAIL
CLAMP SOCKET WRENCHWASHER
(DRIVER)
FLAT
NUT THREADED ROD (RECEIVER)EYENUT
SPRING
PIPE
XJ SUSPENSION 2 - 15
REMOVAL AND INSTALLATION (Continued)
(1) Assemble tools shown (Fig. 3). Tighten nut at
the socket wrench end of the threaded rod until the
bushing is forced out.
Fig. 2 Stabilizer Bar
(4) Disconnect the stabilizer bar link from the
spring bracket stud.
(5) Remove nuts, U-bolts and spring bracket from Fig. 3 Spring Eye Bushing Removal
axle.
(6) Remove nut and bolt attaching spring front eye (2) Assemble and align the bushing installation tools.
to shackle. (3) Align the bushing with the spring eye or
(7) Remove nut and bolt from spring rear eye. shackle eye and tighten the nut at the socket wrench
(8) Remove spring from vehicle. end of the threaded rod. Tighten until the bushing is
forced into the spring eye.
INSTALLATION
(1) Position the spring front eye in the bracket. NOTE: The bushing must be centered in the spring
Loosely install the attaching bolt and nut. Do not eye. The ends of the bushing must be flush or
tighten at this time. slightly recessed within the end surfaces of the
(2) Position the rear eye in the shackle bracket. spring eye.
Loosely install the attaching bolt and nut. Do not
(4) For front bushings bend tabs up after installation.
tighten at this time.
(3) Position the axle. Install the spring bracket,
U-bolts and nuts. Tighten the nuts to 70 N·m (52 ft.
SPECIFICATIONS
lbs.).
(4) Connect the stabilizer bar link to the spring
TORQUE CHART
bracket. DESCRIPTION TORQUE
(5) Remove the hydraulic jack. Shock Absorber
(6) Lower the vehicle. Upper Bolt . . . . . . . . . . . . . . . 23 N·m (17 ft. lbs.)
(7) Tighten the spring front eye attaching bolts to Lower Nut . . . . . . . . . . . . . . . . 62 N·m (46 ft. lbs.)
156 N·m (115 ft. lbs.). Stabilizer Bar
(8) Tighten the spring rear eye attaching bolts to Clamp Bolt . . . . . . . . . . . . . . . 54 N·m (40 ft. lbs.)
108 N·m (80 ft. lbs.). Link Upper Bolt . . . . . . . . . . . . 12 N·m (9 ft. lbs.)
(9) Tighten the stabilizer bar link to 74 N·m (55 ft. Link Lower Nut . . . . . . . . . . . 74 N·m (55 ft. lbs.)
lbs.). Spring
U-Bolt Nut . . . . . . . . . . . . . . . 70 N·m (52 ft. lbs.)
LEAF SPRING AND SHACKLE BUSHING Front Pivot Bolt . . . . . . . . . . 156 N·m (115 ft. lbs.)
For front bushings bend tabs DOWN before Upper Shackle Bolt . . . . . . . 156 N·m (115 ft. lbs.)
removal. Use an appropriate driver tool and force the Lower Shackle Bolt . . . . . . . . 108 N·m (80 ft. lbs.)
original bushing out of the spring eye.