8 Steps Operation Instruction of EVA Vacuum Glass Laminating Machine-V2MAY28
1. 8 Steps Operation Instruction of EVA
Vacuum Glass Laminating Machine
By ZAC GLASS www.helloglass.com
(Notes: the following is a general guide, there is no guarantee that they are all
correct or suits your laminating machine. So if you have doubts please feel free to
contact us. )
1.
Prepare the glasses, Better use edging machine to edge the glasses.
2.
Prepare same size glasses, pay attention to the four corners, it must be edging like
round arc, to avoid breaking the silicone vacuum bag, wash the glass with washing
machine, better be air-dried, this is very important to avoid bubbles inside laminated
glass.
3.
Cutting Eva film, cut the EVA film a little larger than the two glasses(about 2mm
UCOLIN SILICONE TECH
(1)-Silicone Vacuuming Bag for EVA Glass Laminating Machine/Privacy Glass Laminating
(2)-Silicone Sheet for EVA Glass Laminating Machine
(3)-Silicone Bag for PVB Glass Laminating Auto-clave
(4)-Silicone Rubber Sheet for Solar Cell Module Laminating Machine
(5)-Contact Us: uc@ucolin.com / www.ucolin.com
umewe360@gmail.com/ umewe360@hotmail.com
2. lager).
4.
Lie down one glass on the working table, put EVA film onto it, and also put the other
decorative materials(if necessary), then put another glass onto it, cut out the rest EVA
film and decorative materials, stick the 4 corners then.
Picture: sandwiched glass before heating
5.
Put sandwiched glass into the silicone vacuum bag, put the sandwiched glass onto the
vacuum iron table, you should leave 1cm distance between the sandwiched glasses.
After finishing this, connecting the vacuum pipe, as picture blow.
UCOLIN SILICONE TECH
(1)-Silicone Vacuuming Bag for EVA Glass Laminating Machine/Privacy Glass Laminating
(2)-Silicone Sheet for EVA Glass Laminating Machine
(3)-Silicone Bag for PVB Glass Laminating Auto-clave
(4)-Silicone Rubber Sheet for Solar Cell Module Laminating Machine
(5)-Contact Us: uc@ucolin.com / www.ucolin.com
umewe360@gmail.com/ umewe360@hotmail.com
3. 6.
Start vacuum pump, first check the wire connecting of the vacuum pump right or
wrong, then start the vacuum pump, when the vacuum indicator shows lower than
-0.1MPA and become steady, close the door, and wait till to finish the whole process.
7.
Control process setting: first set the technology data to the control plane, as picture
below:
Glass thickness Timing 55℃ 130℃ Lower
(mm) (minute) low high temperature
temperature temperature timing
timing (minute) (minute)
(minute)
3mm+3mm 5 10 40 45
4mm+4mm 5 10 45 50
5mm+5mm 5 10 45 50
6mm+6mm 5 15 50 50
8mm+8mm 5 15 60 60
10mm+10mm 5 20 75 60
UCOLIN SILICONE TECH
(1)-Silicone Vacuuming Bag for EVA Glass Laminating Machine/Privacy Glass Laminating
(2)-Silicone Sheet for EVA Glass Laminating Machine
(3)-Silicone Bag for PVB Glass Laminating Auto-clave
(4)-Silicone Rubber Sheet for Solar Cell Module Laminating Machine
(5)-Contact Us: uc@ucolin.com / www.ucolin.com
umewe360@gmail.com/ umewe360@hotmail.com
4. PS. H-hour, M-minute, S-second
8.
After processing is finished, then open the door, temperature lower sharply, when the
temperature lower to 80~90℃, use fan to blow wind into the machine to fasten
cooling, the temperature under 40℃~50℃, then stop the lower temperature process,
take out the glass. During lowering the temperature procedure, please don’t close the
vacuum pump.
Copyrights:
All Rights Reserved By UCOLIN SILICONE TECH
(1)-Silicone Vacuuming Bag for EVA Glass Laminating Machine/Privacy Glass Laminating
(2)-Silicone Sheet for EVA Glass Laminating Machine
(3)-Silicone Bag for PVB Glass Laminating Auto-clave
(4)-Silicone Rubber Sheet for Solar Cell Module Laminating Machine
(5)-Contact Us: uc@ucolin.com / www.ucolin.com
umewe360@gmail.com/ umewe360@hotmail.com
UCOLIN SILICONE TECH
(1)-Silicone Vacuuming Bag for EVA Glass Laminating Machine/Privacy Glass Laminating
(2)-Silicone Sheet for EVA Glass Laminating Machine
(3)-Silicone Bag for PVB Glass Laminating Auto-clave
(4)-Silicone Rubber Sheet for Solar Cell Module Laminating Machine
(5)-Contact Us: uc@ucolin.com / www.ucolin.com
umewe360@gmail.com/ umewe360@hotmail.com