This document discusses adsorption at liquid surfaces and interfaces. It defines positive and negative adsorption, where some solute molecules are partitioned in favor of the surface/interface (positive adsorption) while others favor the bulk liquid (negative adsorption). Surfactant molecules that reduce surface/interfacial tension through positive adsorption are also introduced. The document then describes how surfactant molecules have both a polar head and nonpolar tail, and how they orient at interfaces. It discusses micelle formation above the critical micelle concentration and how this affects physical properties. In summary, the document provides an overview of adsorption phenomena at liquid surfaces/interfaces with a focus on surfactant molecules and micelle formation.
2. Adsorption is the adhesion of atom , ions or molecules from a gas, liquid, a dissolved solid to a
surface.
Certain solute molecules and ions when added to a liquid are partitioned in favour of surface or
the interface
This is termed as POSITIVE ADSORPTION
Some other solute molecules or ions are partitioned in favour of bulk of the liquid
This is termed as NEGATIVE ADSORPTION
3. NEGATIVE ADSORPTION POSITIVE ADSORPTION
Molecules partitioned in favour
of bulk
Molecules partitioned in favour
of surface/interface
Increase in the surface tension Decrease in the surface tension
Eg: Glucose, Sodium Chloride Eg: Tweens, Spans
4. Solute molecules or ions that are adsorbed at surface/interface and reduce the
surface/interfacial tension are termed as SURFACTANTS (SURFACE ACTIVE
AGENTS)
Surfactant molecules are amphiphiles
They contain a POLAR HEAD and a NON POLAR TAIL
When a surfactant is added to water
Hydrophilic head will be oriented towards water
Lipophilic end will be oriented away from water
Surfactant may be Hydrophilic if it is predominantly polar in nature and
Lipophilic if it is predominantly non polar
5.
6. When same solute is added to an immiscible system
Hydrophilic head will be oriented towards aqueous phase (away from oil)
Lipophilic end will be oriented towards oil phase (away from water)
7. At lower concentration surfactant molecules will be distributed at
the surface and the surface will not be completely filled
As concentration increases the surface is filled up progressively
and finally the surface will be saturated with surfactant with a
marked decrease in the surface tension
8.
9. After the saturation of the surface of the liquid the molecules will
move into the bulk of the liquid and associated into small
aggregates called MICELLES
Micelles formed are of spherical shape in colloidal dimension
(0.001 - 0.5µm)
Each micelle contains around 50 – 100 surfactant molecules
11. In polar solvents polar groups of the surfactants will be oriented
towards the aqueous phase and non polar groups will be oriented
towards the centre of spherical structure of the micelle
12. In non-polar solvents non polar groups of the surfactants will be
oriented towards the non aqueous phase (oil) and non groups will
be oriented towards the centre of spherical structure of the micelle
13. The lowest concentration of the surfactant in bulk of the liquid, at which
the formation of micelles starts is called CRITICAL MICELLAR
CONCENTRATION
CRITICALMICELLARCONCENTRATION
Micelles are generally spherical in shape but they are believed to be
rearrange to lamellar shape at higher concentration
Initially the surfactant molecules are adsorbed at the liquid – air and
liquid – container interfaces.
With further addition of surfactant these interfaces become more and
more crowded with the molecules until they are so tightly packed that
further occupancy of requires excessive compression
This state is called saturation adsorption
14. Further addition of surfactants from this state the increase in
concentration at the interface/surface will be very low but concentration
will increase in the bulk of the liquid.
At CMC formation of association colloids (Micelles) within the bulk of
the liquid will results in marked change in physical properties such as
Conductivity, Density, Viscosity, Osmotic pressure, etc
These may be used to find out CMC of the surfactant
SURFACTANT CMC (mM/ml) Aggregation Number
Potassium laurate 24 50
Sodium lauryl sulphate 59.8 60
15.
16. It ionises in aqueous solutions to yield a large anion and a
small cation
This anions are responsible for its action
Potassium stearate soap
di(2-ethyl hexyl) sodium sulpho succinate
Sodium cetyl succinate
Sodium lauryl sulphate
They are mostly carboxylates
17. It ionises in aqueous solutions to yield a large cation and a
small anion
This cations are responsible for its action
Cetrimide (Cetyl trimethyl ammonium bromide)
They are Amines and Quaternary Ammonium salts
Mainly used as anti microbial agents and preservatives
18. Contain Carboxylate/Phosphate groups as anion
Ammonium/Quaternary ammonium groups as cations
They include Polypeptides, Proteins, Cephalins, Lecithins,
etc.
N- dodecyl alanine
19. Widely used in pharmaceutical industries
Do not ionises in aqueous solutions
Polyoxy-ethylene sorbitan fatty acid esters
Tweens, Spans,etc
21. Surfactants are amphiphiles which containing both Polar and Non polar groups
within a single molecule
The characteristics and applications of surfactants are based on the fraction of
polar or non polar groups present in the molecule
Balance between hydrophilic and lipophilic character is expressed in terms of
HLB values
HLB (Hydrophilic Lipophilic Balance) scale is an arbitrary scale (number
system)which indicates the extend of polar and non polar nature of a surfactant
HLB scale is described by Griffin in 1949