Mobile mini thermal printer for lift truck load weight printout ticket from Freightweight, SkidWeigh systems

1. MPT2 Series
MINI MOBILE THERMAL PRINTER

2. PAPER LOADING
Insert paper roll into paper case. Pay attention
to the direction of the paper. Pull paper out of
paper case. From the bottom of the paper roll
insert the paper into the slot and press FEED
button. Make sure paper is in the center, than
close upper cover.
PRINTER MOUNTING BRACKET
On-board printer mounting bracket
PRINTER INTERFACE
• Data Transfer: Serial
• Synchro Mode: Asynchronous
• Handshaking: Hardware RST/CTS
• Signal Level: RS-232
• Baud Rate: 1200,2400,4800,9600
• Data Bit: 7bit, 8 bit optional
• Parity: Odd,Even,None optional
• Stop Bit: 1 bit
STANDARD ACCESSORIES
• Rechargeable Li-ion battery
• Paper Roll
• Environmental Case
• Interface Cable RS-232
• Power cable
FEATURES
• The smallest 2” mobile printer
• Lightest weight for true mobility
• High speed thermal method printing
• Support text and graphic printing
• 1.2 m free fall into concrete
The MPT2 Mini Mobile Thermal Printer uses a Lithium rechargeable battery pack. Before the first use the battery pack should
be charged for at least 4 hours. (If the printer not connected directly to the SkidWeigh product line)
Use two fingers to
press this place and
open the upper cover
Upper
Cover
Power
input cable

3. THERE ARE TWO LED INDICATORS FOR MPT2 PRINTER
LED indicators show current status and buzzer indicates the changes of status
THERE ARE TWO LED INDICATORS FOR MPT2 PRINTER
LED indicators show current status and buzzer indicates the changes of status
THERE ARE TWO LED INDICATORS FOR MPT2 PRINTER
LED indicators show current status and buzzer indicates the changes of status
THERE ARE TWO LED INDICATORS FOR MPT2 PRINTER
LED indicators show current status and buzzer indicates the changes of status
PRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZERPRINTER’S TWO LED INDICATORS AND BUZZER
LED LIGHT INDICATOR
(BLUE)
LED LIGHT INDICATOR
(RED)
STATUS BUZZER
Flash quickly Dark Charging
Flash slowly Dark Out of power
Continuously bright Dark Charging finished
Dark Continuously bright Working
Flash slowly Flash slowly Paper end Warning
Dark Flash slowly Standby
PRINTER ON / OFF
The printer is powered on by pressing the power button for about one second.
The Red solid LED light (Left) will be activated.
To turn power to the printer OFF, press power button again for about 2 second.
(When printer is turned OFF all LED’s will be turned off as well)
Note: When power indicator LED red light is changed to blue color and is blinking
this indicates that the printer battery must be charged. (If printer not connected to
SkidWeigh products)
SELF TEST
PAPER FEEDING
PAPER TEARING
The self-test checks the printer’s current settings, status and whether the printer
has any problems. To activate the self-test turn holding down the FEED button while
press power button for about 3 seconds. The printer is ready to receive data as
soon as it completes the self-test.
During the normal operation to feed paper hold down FEED button.
To stop paper feed release FEED button.
After each print out ticket / receipt is finished printing, tear off the paper along the
tear bar.
Note: When tearing do not use too much force in order to avoid paper being pulled
out from the paper case.
Operational
Specifications
FEED
BUTTON
POWER
BUTTON

4. General
Specifications
MODEL MPT2
Physical Specifications
Dimensions 92.5 x 75 x 38 mm
Weight 205 g (Paper roll excluded)
Paper Diameter Max. 40 mm
Printing Specifications
Printing Method Line thermal
Paper Width 58 mm
Dot / line 384 dots
Printing Speed 50 - 80 mm/s
Paper Thickness 0.06 - 0.085 mm
Black Mark Checking Available
Paper roll diameter 30 mm
Built in Character Set English: ASCII (8 x 8 / 12 x 12)
Interface Specifications
Cable Connection RS-232
Wireless (Optional) IrDA / Bluetooth
Power Specifications
Battery 1500mAh /7.4V
Power Adaptor * 12 V DC / 1.5A
Battery Duration 150 - 200 m continuous printing (25% density)
Environmental Specifications
Operation
Temperature / Humidity
-10 C - 50 C
20% - 80%
Charging
Temperature . Humidity
5 C - 35 C
20% - 80%
Storage
Temperature / Humidity
-20 C - 60 C
5% - 95%
* Power Connection to
SkidWeigh Products
Direct power connection cable to
SkidWeigh products operating from 12 V DC to 55 V DC
Integrated Visual Data Technology Inc.
3439 Whilabout Terrace
Oakville, Ontario
Canada L6L 0A7
Phone: 905-469-0985
Fax: 905-825-9494 MPT2 Mini Mobile Thermal Printer V.10
Infrared
interface
RS-232
socket
Printer
bracket