We sell dryer parts for various brands including dryer heating element, thermal fuse dryer, belts, cords, motor, timer, thermostat and other parts for dryer.
Good Stuff Happens in 1:1 Meetings: Why you need them and how to do them well
Troubleshooting Tips For a Gas Dryer Not Heating
1. Is your gas dryer not heating properly?
There may be various reasons for the problem…….
But the most common sources of the problem of
dead dryer comes from several areas:
• Igniter and Thermal Fuse
• Thermostat and Radiant flame sensor
• Power Issues
• Heating coils for gas valve
• Overloading
• Wrong Settings
2. Cause #1 :: A Broken Igniter or a Broken Timer
Most primary cost for a dryer not heating is a broken
igniter. If the igniter does not work properly, it will
Not ignite the heater and the dryer unit will not dry
your cloths.
Check for blown fuses, as well as other broken
elements, as these could also be contributing to
the problem. A broken timer could also cause
the heater and the blower to stay inactive.
3. Cause #2 :: Defective Thermostat and Sensors
Another reason may be a defective thermostat.
When The thermostat is not fitted under the lint
trap or it is not attached to the blower housing,
the dryer may not dry. In this case, you need to
replace the broken thermostat.
The sensor could also experience the same problem.
Sensors are like silver discs and they are located under
the drum. If they stop working, then the entire unit will
fail to dry cloths.
4. Cause #3 :: Failed power Connection
Check if the dryer is properly plugged in and then
check the wires and connections. it needs around
110 volts in a gas dryer to heat-dry cloths
Sometimes the dryer mail fail to power up due to over
heating during previous use. The power cords may
burn out for this reason and the dryer require a
repairing service to correct the problem.
5. Cause #4 :: Defective Gas Valve Coils
If there is a defect on the gas valve coils the dryer
Will not heat. If the vent is Clogged, then it prevent
airflow and will raise the temperature higher than
what is set.
Gas valve coils, which normally let the valve open
and allow the gas to pass through, may need to
be replaced or perhaps you just need to give the
valves and the vents a thorough cleaning.
6. Cause #5 :: Dryer Overloading and choosing wrong drying option
Avoid filling the dryer with excess clothes and make
sure that the air can flow freely inside the drum.
Overloading a dryer will prevent the dryer from
drying the load completely
You should choose proper drying setting for
Proper result. Choosing the ‘DRY’ option will
Leave the unit On for long time. Choose the
‘NORMAL’ option for delicate fabrics.
7. To troubleshoot the problem you need to check
for any blown or broken parts. Telltale signs
include smoky odors or a charred appearance
in some dryer areas.
You will need to open the dryer up in order to
see what is inside. Then replace the affected part
With Do-it-yourself appliances repairing parts from
Pandora’s OEM (www.pandorasoem.com) .
You can also email us your model number
and/or question and get an answer the same day!
8. …………… Some of our top selling products are ………….
Dryer Blower Wheel Dryer Control Board Dryer Heater Relay
Dryer Knob Dryer Temp Thermostat Dryer Thermostat
9. Our Store address ::
Pandora's OEM Appliance Parts
PO Box 330919
Murfreesboro, TN 37133
Website Address :: www.pandorasoem.com
Fax ::
1-(615)-890-0107
All parts sold on Pandorasoem.com offer
You (the Customer) a free domestic
shipping option.