The Guide Right Surgical Guide System is a system of components for the fabrication and correction of diagnostic and surgical dental implant guides in 1 or 2 dimensions.

1. Maxillary Single Implant Case
Angular & Linear Correction in 2 Planes
 Bending Tool ► 2 Bends
Featuring:  Offset Guide Posts
 Open Guide Sleeves
 GALAXIS software
#7
MAY 2.2013

2. Fabrication of DIAGNOSTIC Guide

3. #7
Initial wax up.

4. A hole is drilled through the prosthetically planned
long axis of the implant into the cast with a 3/32” drill.
A 3 mm guide post is placed in the hole.

5. A straight 3 mm guide sleeve is placed on the 3 mm guide post
with the cleats positioned toward the palatal surface.

6. Close up showing guide sleeve cleats positioned to the palatal.

7. Lubricant is applied to cast prior to fabrication to enhance removal of guide from
cast. Triad® Gel is added to the guide sleeve to capture the cleats, including
lingual & incisal surfaces of several of the adjacent teeth,. After curing the
DIAGNOSTIC guide & securely seating it in the patient, an X-ray is taken.

8. PRE-OPERATIVE
Evaluation
GALAXIS Cone Beam Images

9. Preview of Pre-op Corrections
#7
LINEAR CORRETION
1.5 mm offset toward the palatal
ANGULAR CORRECTION
1st Bend: 10° bend to the facial
2nd Bend: 5° bend toward the mesial

10. SURGICAL guide
3.0 x 1.5 mm offset guide post toward the palatal is used

11. LINEAR CORRECTION: 1.5 mm toward the palatal
1st ANGULAR CORRECTION: 10° toward the facial
DIAGNOSTIC guide sleeve in place
F F
GALAXIS
cross sectional views

12. Guide Right™
Generation ll / Guide Post Bending Tool
Single 10° bend in one plane

13. Guide Right™
Generation ll / Guide Post Bending Tool
• A straight 3 mm magnetic guide post is placed in the bending tool.
• The 3mm stylus is place over the post.
• Pressure is applied to the point of the stylus to bend the post 9 °
according to the reading on the protractor.

14. Guide Right™
GENERATION II / GUIDE POST BENDING TOOL
SINGLE BEND review
Step 1 Place bending tool plate on a secure flat surface with the degree increments
at the top & the stainless steel bar with the v-cut at the bottom.
Step 2 Locate 3/32” hole in the center of the v-cut and place the bottom half of the
guide post into the hole. Tighten the set screw.
Step 3 Locate the hole in the bottom of the stylus that you will use that will fit over
the top half of the guide post (3.0 mm, 4.0 mm or 5.0 mm).
Step 4 Fit the stylus over the guide post securely with the point directed at
zero degrees and the bottom of the stylus in contact with the V block.
Step 5 Using the stylus as a lever, bend the guide post to the degree of angle of
correction. You may need to ease the point of the stylus beyond the
point of the desired degree.
Step 6 Loosen screw and remove guide post and the stylus to find the guide post
bent to the desired angle.

15. 2nd ANGULAR CORRECTION: 5° toward the facial
Tangential (mesio-distal) 5 ° correction
GALAXIS

16. Guide Right™
GENERATION II / GUIDE POST BENDING TOOL
COMPOUND BEND overview
Step 1 Position a straight or offset guide post in the bending plate, tightening the set
screw against one of the flat surfaces on the lower half of the guide post.
Step 2 The 1st bend can be made to the right or left direction.
Step 3 The set screw is loosened and the guide post is rotated 90 ° next flat surface.
Step 4 The 2nd bend in the second plane is made after rotating the guide post up away
from the surface of the bending plate to register the stylus point back at 0 degrees.
Step 5 Slide the stylus support bar down under the stylus until it supports the stylus.
Tighten the side screws before making the second bend.
Step 6 The second bend can be made in either direction according to the x-ray.
Step 7 Remove the stylus and place the guide post back in the cast with the
appropriate side indicated by a mark facing the buccal or lingual surface.
Be sure the post is in the correct position.
If the post needs to be corrected by a linear movement an offset guide post can be used.
Off sets available in the 3 mm guide post: 0.5,1,1.5, 2.0 ,or 3.0 mm.

17. Magnetic Guide Posts
Straight
 3.0 mm od
Offset
 3.0 od X 0.5 mm os
 3.0 od X 1.0 mm os
 3.0 od X 1.5 mm os
 3.0 od X 2.0 mm os
 3.0od X 2.5 mm os
 3.0 od X 3.0 mm os

18. Guide Right™
Generation ll / Guide Post Bending Tool
Showing required 5° mesio-distal correction with stylus support bar in place.
2nd BEND

19. Fabrication of SURGICAL Guide

20. Palatal view:
1.5 mm offset guide post
offset placed toward the facial
Facial view:
1.5 mm offset guide post in place

21. Facial view:
guide sleeve in place
Facial view:
Triad® Gel added
to form the SURGICAL guide

22. Direction Indicator placed
Final implant placement.
after 2 mm drill is used.

23. Guide Right™
Products shown in this case
 3/32” drill
 3 mm Guide Post
 3 mm Guide Sleeve
 1.5 mm Offset Magnetic Guide Post
 3 mm Open Guide Sleeve
 2 mm Direction Indicator
 Petroleum Jelly
 Generation ll/ Guide Post Bending Tool
 Triad® Gel
1.800.314.0065 • www.deplaque.com

24. DéPlaque
Guide Right™ Surgical Guide System
fabricate ▪ evaluate ▪ correct ▪ verify ▪ place
Start With Precision. Place With Confidence.™
1.800.314.0065 • www.deplaque.com