What Causes BMW Chassis Stabilization Malfunction Warning To Appear
Mechanic motor vehicle tool list with picture and uses
1. Mechanic Motor Vechicle
S.No.
Item with specification
( Mechanic Motor
vechicle)
USES IMAGE
1
Allen Key set of 12
pieces (2mm to 14mm)
Allen key or Allen wrench is a
tool used to drive bolts and screws with
hexagonal sockets in their heads.
2
Caliper inside 15 cm
Spring
A caliper is a device used to measure the
distance between two opposite sides of an
object.
3
Calipers outside 15 cm
spring
A caliper is a device used to measure the
distance between two opposite sides of an
object.
4
Center Punch 10 mm.
Dia. x 100 mm.
It is usually used to mark the center of a
hole when drilling holes.A center
punch forms a large enough dimple to
"guide" the tip of the drill
5 Dividers 15 cm Spring
dividers, can be used as tools to measure
distances, in particular on maps and for
marking
6
Electrician Screw
Driver 250mm
An electrician's screwdriver is a device
used to drive screws into a material by
turning and it is insulated to protect
against shocks,
7
Hammer ball peen 0.5
kg with handle
Ball peen hammers are commonly used to
drive cold chisels, set rivets, and bend and
shape metal.
MECHANIC MOTOR VEHICLE GAS RAHAT ITI BHOPAL
6/2/2017 JR 1/TO/MMV/GITI/BHOPAL
2. Mechanic Motor Vechicle
8
Hands file 20 cm.
Second cut flat
A second cut file is a grade or pitch finer
than a bastard fileand
is used for cutting hard metals.
9
Philips Screw Driver
set of 5 pieces (100 mm
to 300 mm)
A Phillips screwdriver is a tool that has a
cross shape and features the ability to self
center.
10
Pliers combination 20
cm.
combination pliers used for gripping
11
Screw driver 20cm.X
9mm. Blade
The tool used to drive a slotted screw
head is called a screwdriver.
12
Screw driver 30 cm. X
9 mm. Blade
The tool used to drive a slotted screw
head is called a screwdriver.
13 Scriber 15 cm
A scriber is a hand tool used in
metalworking to mark lines on workpieces
14
Spanner D.E. set of 12
pieces (6mm to 32mm)
A wrench that is used for gripping the
nuts on the ends of tubes with both ends
open and having different sizes.
15
Spanner, ring set of 12
metric sizes 6 to 32
mm.
A wrench that is used for gripping the
nuts on the ends of tubes situated at some
depth.
6/2/2017 JR 2/TO/MMV/GITI/BHOPAL
3. Mechanic Motor Vechicle
16
Spanners socket with
speed handle, T-bar,
ratchet and universal
upto 32 mm set of 28
pieces with box
A socket wrench is a type of wrench
or spanner that has a socket attached at
one end, usually used to turn a fastener.
17
Steel rule 30 cm inch
and metric
A steel rule is a simple measuring
instrument that is used for measuring
distances and ruling straight lines
18
Steel tool box with lock
and key (folding type)
400x200x150 mm
A toolbox (also called toolkit, tool
chest or workbox) is a box to organize,
carry, and protect the owner's tools.
19 Wire cutter and stripper
A wire stripper is a small, hand-held
device used to strip the electrical
insulation from electric wires.
6/2/2017 JR 3/TO/MMV/GITI/BHOPAL
4. Mechanic Motor Vechicle
S.No.
Item with
specification
USES IMAGE
1
AC alternator slip ring
puller
AC alternator slip ring puller is used to
pullout slip ring from armature.
2
Adjustable spanner
(pipe wrench 350 mm)
An adjustable wrench (US) or adjustable
spanner (UK) is a wrench with a "jaw"
of adjustable width, allowing it to be used
with different sizes of fastener head (nut,
bolt, etc.)
3
Air blow gun with
standard accessories
A steady stream of compressed air is
delivered through a sturdy ...
4 Air Brake Assembly
Air Brake Assembly is a working model
of air brake system for demonstration on
air brake.
5
Air impact wrench
with standard
accessories
a socket wrench power tool designed to
deliver high torque output with minimal
exertion by the user and Compressed air is
the most common power source
6
Air ratchet with
standard accessories
A power wrench is type of wrench that is
powered by other means than human
force. A typical power source is
compressed air
7
Allen Key set of 12
pieces (2mm to 14mm)
Allen key or Allen wrench is a
tool used to drive bolts and screws with
hexagonal sockets in their heads.
B. Tools Instruments and General Shop outfits
6/2/2017 JR 4/TO/MMV/GITI/BHOPAL
5. Mechanic Motor Vechicle
8
Alternator assembly
used for LMV
Alternator assembly used for LMV is used
for dismalting and assembling.
9
Ammeter 300A/ 60A
DC with external shunt
An ammeter (from Ampere Meter) is a
measuring instrument used to measure the
current in a circuit.
10
Angle plate adjustable
250x150x175
An angle plateis a work holding device
used as a fixture in metalworking.
11
Angle plate size
200x100x200mm
An angle plateis a work holding device
used as a fixture in metalworking.
12 Anti theft device
An anti-theft system is any device or
method used to prevent or deter the
unauthorized appropriation of items
considered valuable. Theft is one of the
most common and oldest criminal
behaviours.
13
Anvil 50 Kgs with
Stand
the anvil is used as a forging tool.The
great majority of modern anvils are made
of cast or forged steel
14
Auto Electrical test
bench
A test bench or testing workbench is an
(often virtual) environment used to verify
the correctness or soundness of a design
or model,
15 Battery -charger
A battery charger, or recharger, is a device
used to put energy into a secondary cell or
rechargeable battery by forcing an electric
current through it
6/2/2017 JR 5/TO/MMV/GITI/BHOPAL
6. Mechanic Motor Vechicle
16 Belt Tensioner gauge
Belt tension gauges are used to properly
check drive belt tension on drive belts to
ensure maximum belt and bearing life.
17 Blow Lamp 1 litre
blowlamp is a fuel-burning tool used for
applying flame and heat to various
applications
18
Caliper inside 15 cm
Spring
A caliper is a device used to measure the
distance between two opposite sides of an
object.
19
Calipers outside 15 cm
spring
A caliper is a device used to measure the
distance between two opposite sides of an
object.
20
Car Jet washer with
standard accessories
it is used to wash the vehicle with high
pressure.
21
Carburetor - Solex,
Mikuny for dismantling
and assembling
Carburetor - Solex, Mikuny for
dismantling and assembling during
practical time.
22
Carburetor repair tool
kit
its used to repair carburetor
23
Chain Pulley Block-3
ton capacity with tripod
stand
chain pulley blocks are the most
commonly used lifting devices.
6/2/2017 JR 6/TO/MMV/GITI/BHOPAL
7. Mechanic Motor Vechicle
24 Chisel 10 cm flat
it is used for for carving or cutting a hard
material such as wood, stone, or metal by
hand, struck with a mallet,
25
Chisels cross cut 200
mm X 6mm
it is used for for carving or cutting a hard
material such as wood, stone, or metal by
hand, struck with a mallet,
26
Circlip pliers
Expanding and
contracting type 15cm
and 20cm each
Circlips are designed to be removed with
special circlip pliers (snap ring tool US)
which can be reassembled for internal or
external clips
27 Clamps C 100mm
the clamp used to hold together two
workpieces. For clamps used to secure
stage lighting instruments to battens
28 Clamps C 150mm
the clamp used to hold together two
workpieces. For clamps used to secure
stage lighting instruments to battens
29 Clamps C 200mm
the clamp used to hold together two
workpieces. For clamps used to secure
stage lighting instruments to battens
30
Cleaning tray 45x30
cm.
A metal tray used for collecting oil from
engine and many other uses
31
Coil spring compressor
for suspension spring
The spring compressor is an extremely
handy tool for some basic auto repairs.
The spring compressor is a fundamental
device when it comes to fixing problems
related to car suspension.
6/2/2017 JR 7/TO/MMV/GITI/BHOPAL
8. Mechanic Motor Vechicle
32
Compression testing
gauge suitable for
diesel Engine with
standard accessories
A compression test is a instrument to
determine the pressure in side the engine
cylinder.
33
Connecting rod
alignment fixture
This toolis used to precisely check the
straightness of connecting rods ...
34
Constant Mesh Gear
box with stand for
Dismantling and
assembly.
its used for spanner practice.
35
Copper bit soldering
iron 0.25 Kg
A soldering iron is a hand tool used in
soldering.a large copper bit on a handle,
heated in a flame.
36
Cut section Model of
Mock layout of a motor
car -electrical system
working model
this model is used for Demonstration.
37
Cut section models of
shock absorbers
this model is used for Demonstration.
38
Cut section of cross ply
and radial tyres
this model used for demonstration on tyre
construction
39
Cut section working
model of automatic
transmission Gear box
cut model of auto transmission gear box is
used for demonstration.
6/2/2017 JR 8/TO/MMV/GITI/BHOPAL
9. Mechanic Motor Vechicle
40
Cut section working
model of centrifugal
clutch assembly.
Cut section working model of centrifugal
clutch assembly is used for demonstration.
41
Cut section working
model of Diaphragm
clutch assembly.
Cut section working model of Diaphragm
clutch assembly is used for demonstration.
42
Cut section working
model of Single plate
clutch assembly.
Cut section working model of single plate
clutch assembly is used for demonstration.
43
Cylinder bore gauge
capacity 20 to 160 mm
It is used to accurately measure the inside
diameter of a hole, cylinder or pipe. In
conjunction with a micrometer, a bore
gaugewill give you the exact reading of
a bore size
44
Cylinder liner- Dry &
wet liner, press fit &
slidefit liner
The cylinder liner, serving as the inner
wall of a cylinder, forms a sliding surface
for the piston rings while retaining the
lubricant within.
45
DC Ohmmeter 0 to 300
Ohms, mid scales at 20
Ohms
Mega Ohmmeter is used to measure large
resistance values. Milli Ohmmeter is used
to measure low resistance at high accuracy
confirming the value of any electrical
circuit.
46
Demonstration board of
2W Ignition system,
ignition coil
It is used for demonstration of ignition system.
47
Demonstration board of
electronic Ignition
system, ignition coil
It is used for demonstration of electronic
Ignition system.
6/2/2017 JR 9/TO/MMV/GITI/BHOPAL
10. Mechanic Motor Vechicle
48
Demonstration board of
MPFI system
It is used for demonstration of MPFI
system.
49
Depth micrometer 0-
25mm
Depth Micrometers are ideal for making
depth measurements more accurately
50
Dial gauge type 1 Gr. A
(complete with
clamping devices and
with magnetic stand)
An indicator is any of various instruments
used to accurately measure small
distances and angles, and amplify them to
make them more obvious.
51
Different type of
Engine Bearing model
A bearing is a machine element that
constrains relative motion to only the
desired motion, and reduces friction
between moving parts.
52
Different type of piston
model
In an engine, its purpose is to transfer
force from expanding gas in the cylinder
to the crankshaft via a piston rod and/or
connecting rod.
53
Disk brake with caliper
assembly
A disc brake is a type of brake that uses
calipers to squeeze pairs of pads against a
disc in order to create friction that retards
the rotation of a shaft.
54
Distributor -Duel
advance type,
reluctance type
It is use for practical knowledge about it
55 Dividers 15 cm Spring
A caliper is a device used to measure the
distance between two opposite sides of an
object.
6/2/2017 JR 10/TO/MMV/GITI/BHOPAL
11. Mechanic Motor Vechicle
56
Drift Punch Copper 15
Cm
A drift punch is constructed as a tapered
rod,is used as an aid in aligning bolt or
rivet holes
57 Drill point angle gauge
for determining the correct drill point
angle of 59º and the correct length
of drill lips necessary for clean-
cut drilling at maximum feeds and speeds.
58
Drill twist 1.5 mm to 15
mm (various sizes) by
0.5 mm
Drill bits are cutting tools used to remove
material to create holes
59 Drum brake assembly
A drum brake is a brake that uses friction
caused by a set of shoes or pads that press
outward against a rotating cylinder-shaped
part called a brake drum.
60
Electric Soldering Iron
230 V 60 watts 230 V
25 watts
A soldering iron is a hand tool used
in soldering. It supplies heat to
melt solder so that it can flow into the
joint between two workpieces.
61
Electric testing screw
driver
An electrician's screwdriver is a device
used to drive screws into a material by
turning and it is insulated to protect
against shocks,
62
Engineer’s square 15
cm. Blade
It consists of a steel blade inserted and
either welded or pinned into a heavier
body at an angle of 90°.
63 Engineers stethoscope
The stethoscope is an device for
auscultation, or listening to the internal
sounds of an engine cylinder
6/2/2017 JR 11/TO/MMV/GITI/BHOPAL
12. Mechanic Motor Vechicle
64
Executive Auto
Electrical tool kit
all usefull tools in this kit.
65
Feeler gauge 20 blades
(metric)
Feeler gauges are mostly used in
engineering to measure the clearance
between two parts
66 File flat 20 cm bastard
A bastard file is a medium grade or pitch
of file for general purposes,
67
File, half round 20 cm
second cut
A second cut file is a grade or pitch finer
than a bastard fileand
is used for cutting hard metals.
68
File, Square 20 cm
second cut
A second cut file is a grade or pitch finer
than a bastard file and is used for cutting
hard metals
69
File, Square 30 cm
round
this file is square in shape
70
File, triangular 15 cm
second cut
A second cut file is a grade or pitch finer
than a bastard fileand
is used for cutting hard metals.
71
Files assorted sizes and
types including safe
edge file (20 Nos)
Flat Hand Files are designed
for safe filing of internal corners and
where metal must be removed rapidly.
One edge is uncut or "safe" for filing one
surface without damaging an adjoining
one
6/2/2017 JR 12/TO/MMV/GITI/BHOPAL
13. Mechanic Motor Vechicle
72
Flat File 25 cm second
cut
A second cut file is a grade or pitch finer
than a bastard fileand
is used for cutting hard metals.
73 Flat File 35 cm bastard
A bastard file is a medium grade or pitch
of file for general purposes,
74
Front axle ( Rzeeppa
Joint) with stand for
Dismantling and
assembly
They are mainly used in front wheel drive vehicles,
and many modern rear wheel drive cars with
independent rear suspension typically use CV
joints at the ends of the rear axle halfshafts and
increasingly use them on the propshafts (drive
shafts).
75
Fuel feed pump for
diesel
to feed fuel from the fuel tank or under
high pressure to the fuel injection system
76
Fuel injection pump
(Diesel) inline
An Injection Pump is the device
that pumps diesel (as the fuel) into the
cylinders of a diesel engine.
77
Fuel injection pump
dismantling tool kit
/Universal Vice
It consists all the tools required to
dismantling Fuel injection pump
78
Fuel injection pump,
VE pump / Distributor
fuel rotary pump (DPC)
pumps / along with
special tools and
accessories.
An Injection Pump is the device
that pumps diesel (as the fuel) into the
cylinders of a diesel engine.
79
Full floating axle and
semi-floating axle
assembly
Full floating axle and semi-floating axle
assembly is used for demonstration.
6/2/2017 JR 13/TO/MMV/GITI/BHOPAL
14. Mechanic Motor Vechicle
80
Functional/experiment
model of different type
of sensors.
Functional/experiment model of different
type of sensors is used for demonstration.
81 Garage stand
used to get your car up off the ground for
maintenance and cleaning.
82
Gloves for Welding
(Leather and Asbestos)
Welding gloves are personal protective
equipment (PPE) that protect the hands of
welders from the hazards of welding.
83 Glow plug tester
Glow plugs preheat the air in the
combustion chamber in diesel engines so
that they start faster when they are cold.
84
Granite surface plate
1600 x 1000 with stand
and cover
The surface plate is often used as the
baseline for all measurements to the
workpiece.granite surface plates increases
the wear resistance of the plate
85 Grease Gun
The purpose of the grease gun is to apply
lubricant through an aperture to a specific
point
86
Grease Gun heavy duty
trolley type 10 kg
capciaty
Heavy Duty Series Grease Guns are made
for the lubrication professionaly
87 Growler
A growler is an electrical device used for
testing insulation of a motor for shorted
coils
6/2/2017 JR 14/TO/MMV/GITI/BHOPAL
15. Mechanic Motor Vechicle
88
Hacksaw frame
adjustable 20-30 cm
A hacksaw is a fine-toothed saw,
originally and principally made for cutting
metal,hacksaw frame is a part of hacksaw
which holda hacksaw blade.
89
Hammer Ball Peen
0.75 Kg
Ball peen hammers are commonly used to
drive cold chisels, set rivets, and bend and
shape metal.
90
Hammer Chipping 0.25
Kg
A chipping hammer is a tool used to
remove welding slag from a weld and
welding spatter from along side welds
91
Hammer copper 1 Kg
with handle
Copper, brass and leaden mallets are
typically used on machinery to apply force
to parts with a reduced risk of damaging
them, and to avoid sparks.
92 Hammer Mallet
A mallet is a kind of hammer, often made
of rubber or sometimes wood.They are
typically used to form sheet metal, since
they do not leave marks and are less likely
to dent the workpiece
93 Hammer Plastic
they give a softened strike with a positive
drive
94
Hand operated
crimping tool (i) for
crimping up to 4mm
and (ii) forcrimping up
to 10mm
A crimping tool is a device used to
conjoin two pieces of metal by deforming
one or both of them in a way that causes
them to hold each other. The result of
the tool'swork is called a crimp.
95
Hand reamers
adjustable 10.5 to 11.25
mm, 11.25 to 12.75
mm, 12.75 to 14.25 mm
and 14.25 to 15.75 mm
used for more basic enlargement of holes
or for removing burrs. The process of
enlarging the hole is called reaming.
6/2/2017 JR 15/TO/MMV/GITI/BHOPAL
16. Mechanic Motor Vechicle
96
Hand Shear Universal
250mm
It is used to shear the metal sheets.
97 Hand vice - 37 mm It is used to hold small pieces of metal
98
Hollow Punch set of
seven pieces 6mm to
15mm
A hollow punch is a tool used for making
holes in various materials such as leather,
wood, fabric, plastic and thin metal.
99 Horn and Horn relay
A horn relay works by modifying the
connection between the horn and the
input, preventing damage in the system.
100 Impact screw driver
An impact driver is specifically designed
to drive screws and bolts that would
otherwise stall out a cordless drill.
101
Injector - Multi hole
type, Pintle type
Fuel injection is the introduction of fuel in
an internal combustion engine, most
commonly automotive engines, by the
means of aninjector.
102 Injector cleaning unit
It contains all the tools required to clean
the injectors
103
Injector testing set
(Hand tester)
Injector nozzle tester can also
be used to test all kinds of traditional /
mechanical diesel injectors(Non common
rail) and set their opening pressure
6/2/2017 JR 16/TO/MMV/GITI/BHOPAL
17. Mechanic Motor Vechicle
104
Insulated Screw driver
20 cm x 9mm blade
The tool used to drive a slotted screw
head is called a screwdriver.
105
Insulated Screw driver
30 cm x 9mm blade
The tool used to drive a slotted screw
head is called a screwdriver.
106 Left cut snips 250mm
left cutting snips (usually red) will cut
straight and in a tight curve to the left
107
Lifting jack screw type
3 ton, 5ton & 20 Ton
capacity
A jackscrew is a type of jack that is
operated by turning a leadscrew. In the
form of a screw jack it is
commonly usedto lift moderately heavy
weights, such as vehicles
108
Magneto spanner set
with 8 spanners
Magneto spanner set is for ignition
system.
109
Magnifying glass
75mm
A magnifying glass is a convex lens that is
used to produce a magnified image of an
object. The lens is usually mounted in a
frame with a handle
110
Marking out table
90X60X90 cm.
marking out table — provides a true
surface from which to work.
111 Multimeter digital
A digital multimeter (DMM) is a test tool
used to measure two or more electrical
values—principally voltage (volts),
current (amps) and resistance (ohms).
6/2/2017 JR 17/TO/MMV/GITI/BHOPAL
18. Mechanic Motor Vechicle
112
Multi-point fuel
injection pump
MPFi is a fuel injection technique used in
gasoline engines.Multi port fuel
injection injects fuel into the intake ports
of each cylinder's intake valve, rather than
at a central point within an intake
manifold like in spark plugs.
113
Oil can 0.5/0.25 liter
capacity
An oil can (oilcan or oiler) is a can that
holds oil (usually motor oil) for
lubricating machines.
114
Oil pump for
dismantling and
assembling.
The oil pump in an internal combustion
engine circulates engine oil under pressure
to the rotating bearings, the sliding pistons
and the camshaft of the engine.
115
Oil Stone 15 cm x 5 cm
x 2.5 cm
An oil stone. Sharpening stones, water
stones or whetstones are used to grind and
hone the edges
116 Oscilloscope 20MHz
It is a type of electronic test
instrument that allows observation of
constantly varying signal voltages, usually
as a two-dimensional plot of one or more
signals as a function of time.
117
Outside micrometer 0
to 25 mm
It is used to measure outside diameter of
an object
118
Outside micrometer 25
to 50 mm
It is used to measure outside diameter of
an object
119
Outside micrometer 50
to 75 mm
It is used to measure outside diameter of
an object
6/2/2017 JR 18/TO/MMV/GITI/BHOPAL
19. Mechanic Motor Vechicle
120
Outside micrometer 75
to 100 mm
It is used to measure outside diameter of
an object
121 Petrol nozzle
Nozzles are attached to the pump via
flexible hoses, allowing them to be placed
into the vehicle's filling inlet.
122
Philips Screw Driver
set of 5 pieces (100 mm
to 300 mm)
A Phillips screwdriver is a tool that has a
cross shape and features the ability to self
center.
123 Pipe cutting tool
A pipecutter is a type of tool used by
plumbers to cut pipe.
124 Pipe flaring tool
A tool used to flare the end of a pipe for a
fitting.
125 Piston ring compressor
Piston ring compressors compress the
piston rings onto the piston, fitting them
into the cylinder.
126
Piston Ring expander
and remover.
Piston rings are removed from the piston
with a piston ring expander tool. A piston
ring expanderengages the end of piston
rings and expands them for removal.
127
Piston Ring groove
cleaner.
piston ring cleaner tools are designed for
doing a re-ring job on your engine. They
will remove carbon deposits from the
ring grooves
6/2/2017 JR 19/TO/MMV/GITI/BHOPAL
20. Mechanic Motor Vechicle
128
Pliers combination 20
cm.
combination pliers used for gripping
129 Pliers flat nose 15 cm
This is both cutting and holding plier to
bend, re-position and snip wire.Because of
their long shape they are useful for
reaching into small areas
130 Pliers round nose 15 cm
nose pliers are a
specialized plier characterized by their
rounded, tapering jaws and most
commonly used for creating loops in
pieces of wire
131
Pliers side cutting 15
cm
These pliers intended for
the cutting of wire (they are generally not
used to grab or turn anything).
132
Portable electric drill
Machine
Drilling Machine is a machine tool used
for drilling holes in variety of metals.
133 Prick Punch 15 cm
A prick punch is a hardened, long, slender
tool that is machined and ground to a
conical point of 60°. It is used to produce
a 60° dent on the surface of material to act
as a guide when cutting out.
134
Punch Letter 4mm
(Number)
These are used to emboss the impression
of a letter or number into a workpiece
135
Radiator cut section-
cross flow
Radiators are heat exchangers used to
transfer thermal energy from one medium
to another for the purpose of cooling and
heating
6/2/2017 JR 20/TO/MMV/GITI/BHOPAL
21. Mechanic Motor Vechicle
136
Radiator cut section-
down flow
Radiators are heat exchangers used to
transfer thermal energy from one medium
to another for the purpose of cooling and
heating
137 Radiator pressure cap
the radiator cap allowscoolant to be
sucked from the reservoir back into the
engine. If there is sufficientcoolant in the
reservoir, no air gets into the engine.
138
Rear axle full floating
type with stand for
Dismantling and
assembly
Rear axle full floating type with stand
used for Dismantling and assembly
139 Right cut snips 250mm
Right cutting snips will cut straight and
in a tight curve to the Right
140
Rivet sets snap and
Dolly combined 3mm,
4mm, 6mm
a short metal pin or bolt for holding
together two plates of metal, its headless
end being beaten out or pressed down
when in place
141 Scraper flat 25 cm
A hand scraper is a single-edged tool used
to scrape metal from a surface.Flat scraper
is flat in shape.
142
Scraper half round 25
cm
A hand scraper is a single-edged tool used
to scrape metal from a surface.half round
scraper is half round in shape.
143
Scraper Triangular 25
cm
A hand scraper is a single-edged tool used
to scrape metal from a surface. Triangular
scraper is Triangular in shape.and scrapes
sharp corners.
6/2/2017 JR 21/TO/MMV/GITI/BHOPAL
22. Mechanic Motor Vechicle
144 Scriber 15 cm
A scriber is a hand tool used in
metalworking to mark lines on workpieces
145
Scriber with scribing
black universal
scribing block - gauge consisting of a
scriber mounted on an adjustable stand;
used to test the accuracy of plane surfaces.
146
Set of stock and dies -
Metric
A device for making threads on the end of
a joint of pipe or length of rod.
147
Shear Tin Man’s 450
mm x 600mm
It is used to shear the metal sheets
manualy.
148 Sheet Metal Gauge
a gauge for measuring the diameter of
wire and thicknss of sheet.
149 Sher Tinmans 300mm
It is used to shear the metal sheets
manualy.
150
Soldering Copper
Hatchet type 500gms
A soldering iron is a hand tool used
in soldering. It supplies heat to
melt solder so that it can flow into the
joint between two workpieces.
151
Solid Parallels in pairs
(Different size) in
Metric
Parallels come in pairs of two,Parallels are
rectangular blocks of metal,hey are used when
machining with a mill, drill or any other
machining operation that requires work to be
held in a vise or with clamps - to keep work
parallel or raised evenly
6/2/2017 JR 22/TO/MMV/GITI/BHOPAL
23. Mechanic Motor Vechicle
152 Spanner Clyburn 15 cm This is a kind of adjustable sppaner.
153
Spanner D.E. set of 12
pieces (6mm to 32mm)
A wrench that is used for gripping the
nuts on the ends of tubes with both ends
open and having different sizes.
154
Spanner T. flocks for
screwing up and up-
screwing inaccessible
This is a T shape spanner used for
screwing and decrewing the nut-bolts.
155
Spanner, adjustable
15cm.
is a wrench with a "jaw" of adjustable
width, allowing it to be used with
different sizes of fastener head (nut, bolt,
etc.) rather than just one fastener, as with
a conventional fixed spanner
156
Spanner, ring set of 12
metric sizes 6 to 32
mm.
A wrench that is used for gripping the
nuts on the ends of tubes situated at some
depth.
157
Spanners socket with
speed handle, T-bar,
ratchet and universal
upto
A socket wrench is a type of wrench
or spanner that has a socket attached at
one end, usually used to turn a fastener.
158 Spark lighter
A lighter is a portable device used to
create a flame, and to ignite a variety of
combustible
159
Spark plug spanner
14mm x 18mm x Size
Spark plug spanner is used to open spark
plug from IC Engines.
6/2/2017 JR 23/TO/MMV/GITI/BHOPAL
24. Mechanic Motor Vechicle
160
Starter motor axial
type, pre-engagement
type & Co-axial type
Starter motor axial type, pre-engagement
type & Co-axial type is used for
dismelting and assembling during
practical work.
161
Steel measuring tape 10
meter in a case
Steel measuring tape 10 meter is used to
measuring long dimentions upto 10 meter.
162
Steel rule 15 cm inch
and metric
A steel rule is a simple measuring
instrument that is used for measuring
distances and ruling straight lines
163
Steel rule 30 cm inch
and metric
A steel rule is a simple measuring
instrument that is used for measuring
distances and ruling straight lines
164
Steering assembly -
1.Rack & pinion,
2.Worm & roller 3.
Recirculating ball,
4.Power steering
The most conventional steering arrangement is
to turn the front wheels using a hand–operated
steering wheel which is positioned in front of
the driver, via the steering column, which may
contain universal joints (which may also be
part of the collapsible steering column design),
to allow it to deviate somewhat from a straight
line.
165
Straight edge gauge 2
ft.
A straightedge is a tool with an edge free
from curves, or straight, used for
transcribing straight lines, or checking the
straightness of lines
166
Straight edge gauge 4
ft.
A straightedge is a tool with an edge free
from curves, or straight, used for
transcribing straight lines, or checking the
straightness of lines
167 Stud extractor set of 3
A stud extractor is a tool for removing
broken or seized studs.
6/2/2017 JR 24/TO/MMV/GITI/BHOPAL
25. Mechanic Motor Vechicle
168
Stud remover with
socket handle
A stud extractor is a tool for removing
broken or seized studs.
169
Surface gauge with dial
test indicator plunger
type i.e. 0.01 mm
It is normally used to 'scribe' parallel lines. Its
base is heavy and this means it is stable when
in used.Surface gauges sometimes have
magnetic bases and this means they can be
locked onto metalsurfaces making it easier
to use.
170
Synchronous Gear box
with stand for
Dismantling and
assembly.
Synchronous Gear box with stand for
Dismantling and assembly.
171
Tachometer (Counting
type)
A tachometer is an instrument measuring
the rotation speed of a shaft or disk in
RPM
172
Tandem master
cylinder with booster
The tandem master brakecylinder converts the
output force, e.g. of the brake unit, into
hydraulic pressure. It combines the effect of
two serially switched master cylinders in one
housing and is used in the dual circuit brake
systems.
173
Taps and Dies complete
sets BSF
Taps and dies are tools used to create
screw threads, which is called threading.A
tap cuts a thread on the inside surface of a
hole.The die cuts a thread on a preformed
cylindrical rod,
174
Taps and wrenches -
metric
A tap wrench is a hand tool used to turn
taps
175 Telescope gauge
These are a range of gauges that are used
to measure a bore's size, by transferring
the internal dimension to a remote
measuring tool.
6/2/2017 JR 25/TO/MMV/GITI/BHOPAL
26. Mechanic Motor Vechicle
176
Temperature gauge
with sensor 0-100 deg c
Temperature gauge is a meter used to
monitor the gas temperature of an internal
combustion engine..
177
Tester sparking plug
‘NEON’ Type
Use this ignition spark tester to check the
condition of the ignition system at each
cylinder without going to expensive
mechanics.
178 Thermostat
thermostat, used to maintain the engine
near its optimum operating temperature by
regulating the flow of coolant to an air-
cooled radiator.
179
Thread pitch gauge
metric, BSW
A thread gauge, also known as a
screw pitch gauge or pitch gauge, is used
to measure the pitch or lead of a
screw thread.
180 Timing lighter
It is used to set the spark timing of petrol
engine spark plug.
181 Toe-in, toe-out gauge
use to check toe-in and toe-out of front
wheel of vehicle.
182
Torque wrenches 5-35
Nm, 12-68 Nm & 50-
225 Nm
A torque wrench is a tool used to apply
precisely a specifictorque to a fastener
such as a nut or bolt. It is usually in the
form of a socket wrench with special
internal mechanisms.
183 Trammel 30 cm
A beam compass is a compass with a
beam and sliding sockets or cursors for
drawing and dividing circles larger than
those made by a regular pair of
compasses.
6/2/2017 JR 26/TO/MMV/GITI/BHOPAL
27. Mechanic Motor Vechicle
184 Tread wear indicator
Tread wear indicator is used for visual
indication of the degree of wear of the
tread.
185
Tubed tyre of car,
trucks & motorcycle
Tubed tyre of car, trucks & motorcycle is
for diplay and practical.
186
Tubeless tyre of cars &
trucks
Tubeless tyre of cars & trucks to display.
187 Tubeless tyre repair kit
Tubeless tyre repair kit is use to repair
tubless tyre.
188
Turbocharger cut
sectional view
The turbocharger turbine, which consists
of a turbine wheel and a turbine housing,
converts the engine exhaust gas into
mechanical energy to drive the
compressor.
189
Tyre & split rim wheel
assembly
Spilt rims are multi-piece-or-divided rims
and wheels that are held together by bolts
or a lock ring.
190
Tyre pressure gauge
with holding nipple
A tire-pressure gauge is a pressure gauge
used to measure the pressure of tires on a
vehicle.
191
Universal puller for
removing pulleys,
bearings
A bearing puller is a tool used to
remove bearing sets from a rotating
machine shaft or from a blind bearing hole
6/2/2017 JR 27/TO/MMV/GITI/BHOPAL
28. Mechanic Motor Vechicle
192
V’ Block 75 x 38 mm
pair with Clamps
V-Blocks are precision metalworking jigs
typically used to hold round metal rods or
pipes for performing drilling or milling
operations.
193
Vacuum assisted
hydraulics brake
assembly with vacuum
booster
A constant vacuum is maintained in the
brake booster by the engine. When the
brake pedal is depressed, a poppet valve
opens, and air rushes into a pressure
chamber on the driver's side of the
booster.
194
Vacuum gauge to read
0 to 760 mm of Hg.
A vacuum gauge is an absolute
pressure gauge used to measure the
pressures lower than the ambient
atmospheric pressure.
195 Valve Lifter
valve lifter, also known as a
hydraulic tappet or a hydraulic lash
adjuster, is a device for maintaining
zero valve clearance in an internal
combustion engine. Conventional
solid valve lifters require regular adjusting
196
Valve spring
compressor universal.
A valve spring compressor is a tool for
those who are disassembling a cylinder
head and wish to remove the valves and
springs within the head.
197
vernier caliper 0-300
mm with least count
0.02mm
The Vernier Caliper is a precision
instrument that can be used to measure
internal and external distances extremely
accurately.
198 Vice grip pliers
Vice grip pliers are pliers that can be
locked into position, using an over-center
action.
199
Water pump for
dismantling and
assembling
A car engine produces so much heat that
there is an entire system in your car
designed to cool the engine down to its
ideal temperature.
6/2/2017 JR 28/TO/MMV/GITI/BHOPAL
29. Mechanic Motor Vechicle
200 Wheel cylinder
A wheel cylinder is a component in a
drum brake system. It is located in each
wheel and is usually positioned at the top
of the wheel, above the shoes.
201 Wiper motor assembly
A windscreen wiper or windshield wiper
is a device used to remove rain, snow, ice
and debris from a windscreen or
windshield.
202 Wire Gauge (metric)
a gauge for measuring the diameter of
wire and thicknss of sheet.
203
Work bench 250 x 120
x 60 cm with 4 vices
12cm Jaw
They are designed so that the workpiece
can be mounted firmly, usually from
underneath, and accessed from all sides
204
Working Model of
power windows
Power windows or electric windows are
automobile windows which can be raised
and lowered by pressing a button or
switch, as opposed to using a hand-turned
crank handle.
205
Working model of
torque converter
A torque converter is a type of fluid
coupling that is used to transfer rotating
power from a prime mover, such as an
internal combustion engine, to a rotating
driven load.
206 4 Point relays
Relays allow a small current flow circuit
to control a higher current circuit. Several
designs of relays are in use today.
207 5 Point relays
Relays allow a small current flow circuit
to control a higher current circuit. Several
designs of relays are in use today.
6/2/2017 JR 29/TO/MMV/GITI/BHOPAL
30. Mechanic Motor Vechicle
S.No.
Item with
specification
USES IMAGE
1 Air bag simulator
Air bag simulator is used for training on air
bag system. By this equipment trainees
familieat with working of air bag simulator
2
Air conditioned CRDI
Vehicle in running
condition -LMV
This vehicle is used for practical works of
automobile. Like wheel aligment, air bleeding,
engine maintanance, cooling system maintance
etc.
3
Air conditioning
service Unit (Car)
Air conditioning service unit is an advance
machinery which is use for service a air
conditioning unit of Automobile.
4
Air conditioning trainer
kit
air conditioning trainer kit is a working model
of air conditioner which is used in vehicle. The
perpose of this equipment is to perporm
trainnig practice by trainees
5
Arbor press hand
operated 2 ton capacity
Arbor press is used for pressing object.
6
Automotive exhaust 5
gas analyzer (petrol &
Diesel) or Diesel
Smoke Meter
An exhaust gas analyser is an instrument for
the measurement of carbon monoxide among
other gases in the exhaust, caused by an
incorrect combustion.
7
Bench lever shears
250mm Blade x 3mm
Capacity
A bench shear can cut flat bar up to 6mm. it is
a bench mounted shear with a compound
mechanism to increase the mechanical
advantage.
C. General Installation/ Machineries
6/2/2017 JR 30/TO/MMV/GITI/BHOPAL
31. Mechanic Motor Vechicle
8
Diesel Engine - CRDI -
4 stroke for
Dismantling and
assembling with
swivelling stand
CRDI four stroke Diesel engine is used for
Dismantling and assembling.
9
Diesel engine (
Running condition )
Stationary type
Single Cylinder four stroke Diesel engine is
used for diamantiling and assembling.
10
Discrete Component
Trainer / Basic
Electronics Trainer
Used for training on basic electronics.
11
Drilling machine bench
to drill up to 12mm dia
along with accessories
The bench drill is used for drilling holes
through materials including a range of woods,
plastics and metals.
12
Dual Magnetization
Yoke : AC / HWDC,
230 VAC, 50Hz
Dual Magnetization Yoke use as a handle to
lift object
13
Four stroke petrol
engine with CNG setup-
working condition
The Four stroke petrol engine with CNG setup
is used for practical works.
14
Gas Welding Table
1220mm x760mm
You use it when you are working in metal
fabrication with welding. A welding table is
very useful because it gives the welder a stable
place.
15
Grinding machine
(general purpose) D.E.
pedestal with 300 mm
dia wheels rough and
smooth
A grinding machine is any of various power
tools or machine tools used for grinding,
which is a type of machining using an abrasive
wheel as the cutting tool.
6/2/2017 JR 31/TO/MMV/GITI/BHOPAL
32. Mechanic Motor Vechicle
16
Hand operated
Hydraulic press
A hydraulic press is a device using a hydraulic
cylinder to generate a compressive force.
17
Heavy Commercial
vehicle type (without
body on frame)
Heavy Commercial vehicle without body on
frame is a model with maxximum visible parts
so that trainees will familier with chassis of
heavy vehicle.
18
Hydraulic jack HI-LIFT
type -3 ton capacity,
and 5 Ton capacity
A jack is a device that uses force to lift heavy
loads.
19
Liquid penetrant
Inspection kit
Liquid penetrant Inspection kit is used to find
out minor cracks and hair pin cracks on the
chassis
20
MPFI petrol engine
with swiveling stand
along with special tools
for dismantling and
assembling
By this model trainees will familier with the
MPFI system of theAutomobile.
21
Multi Scan Tool with
oscilloscope
It is the X-ray machine of diagnostics, letting
you see the changing signals inside wires.
22
Petrol Engine(2-stroke)
Motor Cycle/Scooter
along with special tools
and accessories
Two stroke petrol engine is used for practicall
work and for spanner practice.
23
Pipe Bending Machine
(Hydraulic type) 12mm
to 30mm
Tube and pipe bending machines are used to
bend tubes and pipes to produce finished parts.
6/2/2017 JR 32/TO/MMV/GITI/BHOPAL
33. Mechanic Motor Vechicle
24
Pneumatic rivet gun
with standard
accessories Spring
tension tester
A rivet gun, also known as a pneumatic
hammer, is a type of tool used to drive rivets.
26
Tin smiths bench folder
600 x 1.6mm
particularly useful where boxes, chasis and
panels with upto 1/2 inch lip or finger across
top or bottom are to be formed with adjustable
material gauge and handle.
27
Transfer case with
stand for Dismantling
and assembly.
A transfer case is a part of the drivetrain of four-
wheel-drive, all-wheel-drive, and other multiple
powered axle vehicles. The transfer case transfers
power from the transmission to the front and rear
axles by means of drive shafts.
28
Trolley type portable
air compressor single
cylinder with 45 liters
capacity Air tank, along
with accessories & with
working pressure 6.5
kg/sq cm
An air compressor is a device that converts
power (using an electric motor, diesel or
gasoline engine, etc.) into potential energy
stored in pressurized air (i.e., compressed air).
29
Tube/ tyre vulcanizing
machine
Vulcanization is a chemical process for converting
natural rubber or related polymers into more
durable materials via the addition of sulfur or other
equivalent curatives or accelerators.
30
Two post car lift -
capacity 4000 kg
A two post above ground lift is designed to raise
cars and trucks for easy access to wheel assemblies
and the underside of the vehicle. A two post above
ground lift is normally mounted to an existing
concrete surface.
31 Tyre Changer Machine
A tire changer is a machine used to help tire
technicians dismount and mount tires with
automobile wheels.
6/2/2017 JR 33/TO/MMV/GITI/BHOPAL
34. Mechanic Motor Vechicle
32
Ultrasonic Injection
cleaning equipment
Ultrasonic cleaning is a process that uses
ultrasound and an appropriate cleaning
solvent to clean items.
33
Welding plant Oxy-
Acetylene complete (
high pressure)
The torch assembly consists of the handle, oxygen
and fuel gas valves and mixing chamber. Welding
tips or a cutting attachment can be used with the
handle allowing it to be used for welding, heating
and cutting operations.
34
Welding Transformer (
150-300 Amps)
A transformer is used to reduce voltage and
increase current.Arc welding is a type of welding
that uses a welding power supply to create an
electric arc between an electrode and the base
material to melt the metals at the welding point.
35
Wheel alignment
Machine -computerised
3D
wheel alignment is part of standard automobile
maintenance that consists of adjusting the
angles of wheels so that they are set to the car
maker's specification.
36
Wheel balancing
machine
Wheel balancing machine is used to balance
the wheel.
37
Working Condition of
Diesel Engine - CRDI -
4 stroke Engine
Assembly with fault
simulation board
To demonstrate the fault and to diagnose faults
38
Working Condition of
Petrol MPFI Engine
Assembly with fault
simulation board
To demonstrate the fault and to diagnose
faults
6/2/2017 JR 34/TO/MMV/GITI/BHOPAL
35. Mechanic Motor Vechicle
S.No.
Item with
specification
USES IMAGE
1
Book shelf (glass
panel) 6½ ‘ x 3’ x 1½’
book shelf is used to manage the books and
documents
2 Computer Chair
computer chair is used for sitting in front of
computer.
3 Computer Table
This computer desk is perfect for any home or
office. It is the best solution to have your
computer on with the ability to use a workable
space.
4
Desktop computer and
related MS office
software
A desktop computer is a personal computer
designed for regular use at a single location on
or near a desk or table due to its size and
power requirements.
5
Discussion Table 8’ x
4’ x 2½ ‘
Round table is a form of academic discussion.
Participants agree on a specific topic to
discuss ... The round table method is still
highly used to this day.
6
Fire Extinguishers, first-
aid box
Pull the pin or ring that unlocks the fire
extinguisher's operating handle, and aim
the extinguisher at the base of the fire. Aim at the fire from
6 to 8 feet away. Squeeze the extinguisher lever to
discharge its contents, and sweep the hose back and forth
until the extinguisher is empty.
7
Instructional Material –
NIMI Books/Ref.books
Instructional materials are the tools used in
educational lessons, which includes active learning
and assessment. Basically, any resource a teacher
uses to help him teach his students is an
instructional material.
E. WORKSHOP FURNITURE
6/2/2017 JR 35/TO/MMV/GITI/BHOPAL
36. Mechanic Motor Vechicle
8
Internet connection
with all accessories
The Internet has many uses including sending
and receiving emails, video conferencing, and
the transferring various files and documents.
9 Laser printer
A printer is a device that accepts text and
graphic output from a computer and transfers
the information to paper, usually to standard
size sheets of paper.
10
LCD projector/ LED
/LCD TV (42”)
An LCD projector is a type of video projector
for displaying video, images or computer data
on a screen or other flat surface.
11
Multimedia DVD for
Automotive
application/subjects
Trades related DVD and Leader' Guide
12 Online UPS 2KVA
Online ups is suitable for use by any
application that demands high quality
electrical supply.
13 Stools
a seat without a back or arms, typically resting
on three or four legs or on a single pedestal.
14
Storage Rack 6½ ‘ x 3’
x 1½’
Rack is a material handling storage aid system
designed to store materials on pallets. Although
there are many varieties of pallet racking, all types
allow for the storage of palletized materials in
horizontal rows with multiple levels.
15
Storage shelf 6½ ‘ x 3’
x 1½’
Shelf is a flat horizontal plane which is used in a home,
business, store, or elsewhere to hold items that are being
displayed, stored, or offered for sale. It is raised off the
ground and usually anchored/supported on its shorter
length sides by brackets.
6/2/2017 JR 36/TO/MMV/GITI/BHOPAL
37. Mechanic Motor Vechicle
16
Suitable class room
furniture
Inspiring educational spaces can change the
way we teach and learn.
17
Suitable Work Tables
with vices
a table at which one may work, especially one
with drawers or compartments for holding
tools or materials.
18
Tool Cabinet - 6½ ‘ x
3’ x 1½’
A cabinet (also tool chest or workbox) is a box
to organize, carry, and protect the owner's
tools. They could be used for trade
19
Trainees locker 6½ ‘ x
3’ x 1½’
trainees locker is used by trainees.
6/2/2017 JR 37/TO/MMV/GITI/BHOPAL