This document provides information about tinting and over dyeing processes for denim garments. It discusses:
- Tinting/over dyeing involves lightly dyeing garments with colors like yellow or pink after fading to give a new fashion or better appearance.
- The process is done on garments after washing techniques like acid wash or stone wash. Direct or reactive dyes are used to color the white/base areas.
- Tinting can be done overall by immersion or localized by spray. It provides a new color effect while maintaining the indigo tone.
- Proper precautions must be taken like fabric and thread matching, and compatible accessories, to avoid irregular dyeing
4. Tinting & Over Dyeing
After denim pant is being faded, the pants have dyed
with very light color(.001% or .002%yellow or pink). This
dyeing process is called Tinting/Over dyeing .This
process is applied only on garments, not in fabric or
yarn.
5. Necessity of Tinting
• For making new fashions.
• To give the finished garments a better appearance.
• For inventing a new process
6. Tinting and over dyeing can be
highlighted by the following way:
• This type of process is done after different types of washing
before softening.
• Normally after Acid wash, Stone wash, Stone enzyme wash,
Sand Blasting, Enzyme wash etc. tinting & over dyeing is done.
• Tinting & over dyeing is done with Direct dyes or Reactive
dyes.
• Due to tinting and over dyeing, the white/base area colored
with required dye yellow, Brown, Orange etc.
• As a result, new color effect is produced in the garments.
• If direct dye is used then color fixing treatment should be done
at the end of dying process. In case over dyeing/Tinting with
reactive dyes, color fastness is good hence no after treatment
is required to fix the reactive dyes.
7. Tint Denim Garments Without
Changing the Tone of Indogo:
Tinting is achieved by application of the direct/reactive dyes. In
case of direct dyes, the second application would be that of dye-
fixing agent for an adequate fastness. In case of reactives, the
fixing chemical goes along with the dyestuff. After the application,
the treated garment is dried in the air or in a tumble drier for
adequate fastness. If tinting were done by immersion method, the
tint would be all over. However, if a localized area is the target, a
spray method is used. In either case the tinting, as the term
signifies, is done very lightly to achieve a particular cast, either
overall or localized. If indigo does not change tone would look like
a print with a sharp boundary. When tone changes fad gradient,
the effect looks more aesthetically appealing and is considered
desirable. The tone-change should be gradual and not abruptive.
8. Tinting With White Discharge
Effect on Denim Garments
In case of white discharge tinting the route would start with
desizing-biopolishing on gray garment, peroxide bleaching
after biopolishing being optional. After drying the garment,
a potassium permanganate spray is given to areas where
white discharge is aimed at. After air-drying for about 10-15
minutes, a neutralization step consisting of provide-acetic
acid is given which is followed by hot and cold rinses. In
case of spray tinting the garment will have to be dried first,
whereas for overall tinting, dyeing the method could be
followed wet-on-wet. Finally the finishing and drying would
complete the process.
9. Tinting by Direct Dye
• First Step: After different wet processing i.e. Acid
wash, Stone wash, Enzyme wash, Stone enzyme
wash, Bleach wash take 60 kg garment for Tinting &
over dyeing.
Water at L : R = 1: 7.............. 420 Liter
Run the Machine.
Temperature................. 50 - 80°c
Dir. Brown GTL - at 0.04%........... 24 Gms.
Dir. Orange ZTL- at 0.01%........... 6 Gms.
Add Salt at 20 gm / liter ............ 8.40 kg.
Add Leveling agent at 0.5% /........ 210 gm.
Time................................ 10 to 30 mts.
Rinse by cold water 3 minutes.
10. Tinting by Direct Dye
• Second Step: Fixing
Batch size .............................. 60 kg.
Water at L : R = 1: 7.............. 420 Liter
Run the Machine.
Temperature................. 50°c
Add fixing agent at 0.8 %(owf) ... 480 gm.
Time............................................ 10 mts.
11. Tinting by Direct Dye
• Third Step: Softening.
Batch size.................... 60 kg.
Water at L : R = 1 : 7 ............................ 420 Liter
Add Acetic Acid at 0.6 gm/liter ............ 250 gm.
Add Cationic softener at 1 gm/liter ...... 420 gm.
Time................................ 10 mts.
Drop the liquor.
Then unload the garments on trolley.
12. Tinting by Direct Dye
• Fourth Step: Hydro extractor machine.
Hydroextractor machine is used to remove
excess water from the garments.
• Fifth Step: - Dryer machine.
After hydro extraction the garments are sent to
drying m/c for complete drying.
• Sixth Step: - Quality & Delivery
After drying the garments go to quality
checking & rectify washing fault and then good
one delivery.
13. Tinting by Reactive dye:
• First Step: After different wet processing i.e. Acid
wash, Stone wash, Enzyme wash, Stone enzyme
wash, Bleach wash take 60 kg garment for Tinting &
over dyeing.
Water at L : R = 1: 7.... 420 Liter
Run the Machine.
Temperature................. 60°c
Reactive Red
Reactive Yellow - Brown ......... 100 gm.
Reactive Black –
Leveling agent - at 0.5 gm / liter.......240 gm.
Salt - at 20 gm / liter........... 8.40 kg.
Soda ash at 10 gm / liter ............ 4.20 kg.
Time................................ 20 to 30 mts.
Drop the liquor.
14. Tinting by Reactive dye:
• Second Step: Fixing.
Batch size.................... 60 kg.
Water at L: R = 1 : 8 .............. 480 Liter
Run the Machine.
Temperature.................................. 50°c
Add fixing agent at1 gm / liter..... 480 gm.
Time............................................. 10 mts.
Drop the liquor.
15. Tinting by Reactive dye:
• Third Step: Softening.
Batch size.................... 60 kg.
Water at L : R = 1: 7.............. 420 Liter
Add Acetic Acid at 0.6 gm/liter ............ 250 gm.
Add Cationic softener at 1 gm/liter ...... 420 gm.
Time................................ 10 mts.
Drop the liquor.
Then unload the garments on trolley
16. Tinting by Reactive dye:
• Fourth Step: Hydro extractor machine.
Hydro extractor machine is used to remove
excess water from the garments.
• Fifth Step: - Dryer machine.
After hydro extraction the garments are sent to
drying m/c for complete drying.
• Sixth Step: - Quality & Delivery.
After drying the garments go to quality
checking & rectify washing fault and then good
one delivery.
17. Precautions
– Garments design should be made from engineering point of view.
– If garment is made after Desizing, scouring and bleaching of grey fabrics and
then dyed in garments form, then the possibility of problems will be reduced.
– If possible, garments should be made from the grey fabrics of the same lot and
same source.
– The seams should not be too tight or too loose especially in the areas
containing elastic like waistband, cuff etc which may create irregular dye
penetration resulting irregular dyeing.
– The garments which are produced from woven and knitted fabrics combinedly,
the knit fabric should be preshrunk; otherwise seam pucker may develop after
garments dyeing.
– If the garment fabric is of mixed fibers, during garments dyeing, dye selection
should be done carefully, having equal dye pick up to avoid irregular dyeing.
– Poor quality metals should not be used as accessories in the garments, which
may be damaged during dyeing by the action of salt and alkali. If any metal
component is used in the garment should be made from nickel and its alloy.
18. Precautions
– Sewing thread used for making the garments should be of same fiber like
the garment fabric, otherwise color difference may occur between the
garment fabric and sewing thread.
– Button used in the garment should be selected carefully. Button made from
casin, cellulose, nylon etc. may be damaged during garments dyeing
but PET button is saved in this respect.
– If elastic is used in the garments and the elastic is made from the natural
rubber or polyurethane fiber like Lycra may create problem during
garments dyeing. To avoid such problem dye should be selected to be
copper free. During bleaching, polyurethane fibers may be damaged by
the chlorine. PET type electrometric fiber is Safe in per oxide bleaching.
– Interlining is used in the most garments. Only those interlinings should be
used in the garments to be dyed only recommended for the garment
dyeing. Otherwise the performance of interlining may be destroyed.
– The garments made from compactly woven cotton fabric should be dyed
with hot brand reactive dyes; otherwise problem of irregular dye
penetration may occur.