1. City University
Subject: Data Communication
Name: Tapash Kumar Roy
What is MAC Address?
MAC address is a unique number which is used to track a device in a network. MAC address provides a secure way
to find senders or receivers in the network and helps prevent unwanted network access. Mac address is also used
in Wi-Fi networks at the airport for a specific device in order to identify it.
What is network interface card (NIC)?
A network interface card (NIC) is a hardware component without which a computer cannot be connected over a
network. It is a circuit board installed in a computer that provides a dedicated network connection to the
computer. It is also called network interface controller, network adapter, or LAN adapter.
What is an IP Address?
An IP (Internet Protocol) address is a numerical label assigned to the devices connected to a computer network
that uses the IP for communication.
IP address act as an identifier for a specific machine on a particular network. It also helps you to develop a virtual
connection between a destination and a source.
What is Classful Addressing?
This addressing method divides the IP address into five separate classes based on four address bits.
Here, classes A, B, C offers addresses for networks of three distinct network sizes. Class D is only used for multicast,
and class E reserved exclusively for experimental purposes.
Now, all class in details:
Class A Network;
This IP address class is used when there are a large number of hosts. In a Class A type of network, the first
8 bits (also called the first octet) identify the network, and the remaining have 24 bits for the host into that
network.
An example of a Class A address is 102.168.212.226. Here, "102" helps you identify the network and 168.212.226
identify the host.
2. Class A addresses- 127.0.0.0 to 127.255.255.255 cannot be used and is reserved for loopback and diagnostic
functions.
Class B Network:
In a B class IP address, the binary addresses start with 10. In this IP address, the class decimal number that
can be between 128 to 191. The number 127 is reserved for loopback, which is used for internal testing on the
local machine. The first 16 bits (known as two octets) help you identify the network. The other remaining 16 bits
indicate the host within the network.
An example of Class B IP address is 168.212.226.204, where *168 212* identifies the network and *226.204* helps
you identify the Hut network host.
Class C Network:
Class C is a type of IP address that is used for the small network. In this class, three octets are used to
indent the network. This IP ranges between 192 to 223.
In this type of network addressing method, the first two bits are set to be 1, and the third bit is set to 0, which
makes the first 24 bits of the address them and the remaining bit as the host address. Mostly local area network
used Class C IP address to connect with the network.
Example for a Class C IP address: 192.168.178.1
Class D Network:
Class D addresses are only used for multicasting applications. Class D is never used for regular networking
operations. This class addresses the first three bits set to "1" and their fourth bit set to use for "0". Class D
addresses are 32-bit network addresses. All the values within the range are used to identify multicast groups
uniquely.
Therefore, there is no requirement to extract the host address from the IP address, so Class D does not have any
subnet mask.
Example for a Class D IP address: 227.21.6.173
3. Class E Network:
Class E IP address is defined by including the starting four network address bits as 1, which allows you two
to incorporate addresses from 240.0.0.0 to 255.255.255.255.
However, E class is reserved, and its usage is never defined. Therefore, many network implementations discard
these addresses as undefined or illegal Example for a Class E IP address: 243.164.89.28
What is HUB ?
It is a non-intelligent network device that sends message to all ports. It primarily broadcasts messages.
Transmission mode is half duplex. Generally it has fewer ports of 4/12. They operate in the physical layer of the OSI
model.
What is switch?
It is an intelligent network device that sends message to selected destination ports. It is supports unicast, multicast
and broadcast. Transmission mode is full duplex. The number of ports is higher – 24/48.
What is router?
A router is a device that connects two or more packet-switched networks or subnetworks. It serves two primary
functions: managing traffic between these networks by forwarding data packets to their intended IP addresses,
and allowing multiple devices to use the same Internet connection.