Pressure Measurement, Manometers, Elastic pressure elements, Bourdon tube pressure gauge, diaphragm gauges, bellows gauges, electrical pressure transducers, deadweight pressure gauge tester

1. Pressure
Measurement
PREPARED BY :
RATNADEEPSINH JADEJA

2. Introduction
 Pressure is defined as a force per unit area.
 Pressures are exerted by gases, vapours and liquids. The instruments that we
generally use, record pressure as the difference between two pressures.
 Devices indicate pressure either above or below that of the atmosphere.
 Atmospheric pressure: The atmospheric air exerts a normal pressure upon all
surfaces with which it is in contact, and it is known as atmospheric pressure. The
atmospheric pressure is also known as barometric pressure.
 The atmospheric pressure at sea level (above absolute zero) is called standard
atmospheric pressure.

3. Introduction
 Gauge pressure: It is the pressure, measured with the help of pressure measuring
instrument, in which atmospheric pressure is taken as datum.
 The atmospheric pressure on the scale is marked as zero.
 Absolute pressure: Any pressure measured above absolute zero of pressure is
termed as an absolute pressure.
Absolute pressure = atmospheric pressure + gauge pressure
Vacuum pressure = atmospheric pressure – absolute pressure

4. Introduction
Positive gauge
pressure Atmospheric pressure
Negative gauge
Pressure or vacuum
Absolute
pressure
Pressure
Zero absolute pressure

5. Simple Manometers
 A simple manometer is one which consists of a glass tube whose one end is
connected to a point where pressure is to be measured and the other end
remains open to atmosphere.
 Common types of simple manometers are enumerated and discussed below:
1. Piezometer
2. U-tube manometer
3. Single column manometer (micro-manometers).

6. Piezometer
A Piezometer is the simplest form of
manometer which can be used for measuring
moderate pressures of liquids.
pressure at point A :
p = w * h
Where,
p = pressure,
w = specific weight of the fluid
h = height of fluid in piezometer tube

7. U-tube
manometer
A U-tube manometer consist of a
glass tube bent in U-shape, one
end of which is connected to a
point at which pressure is to be
measured and other end remains
open to the atmosphere.

8. Single column
manometer
(micrometer)
Single column manometer is
modified form of a U-tube
manometer.
For any variation in pressure,
the change in the liquid level in
the reservoir will be so small
that it may be neglected and
the pressure is indicated by the
height of liquid in the other
limb.

9. Differential
Manometers
A differential manometer is used to
measure the difference in pressure
between two points in a pipe, or in
two different pipes.

10. Elastic Pressure Elements
 Elastic pressure elements or mechanical type of transducers are used for
measurement of very high pressures up to about 700 MN/𝑚2
.
 There are three main types of pressure elements:
1. Bourdon tube
2. Diaphragms
3. Bellows.

11. Bourdon tubes/elements

12. Diaphragm
Gauges &
Elements

13. Bellow
gauges/
elements

14. Bourdon
tube
pressure
gauge
BOURDON TUBE PRESSURE
GAUGE IS USED FOR
MEASURING HIGH AS WELL AS
LOW PRESSURES.

15. Errors in bourdon tube pressure gauge
Following three types of errors are commonly found in bourdon tube gauges:
1. Zero error.
2. Multiplication error.
3. Angularity error.

16. Electrical Pressure Transducers
 A transducers is a device for converting a signal of one sort into other type. In
other words, a pressure gauge is a transducer for converting the distortion of a
bourdon tube into an indication through use of a calibrated dial and so on.
 In case of electrical transducers for measuring pressure, various transformations
which are needed to convert pressure to some sort of usable electrical signal.

17. Resistance Type Pressure Transducers
Resistance type devices used in
pressure transducers include:
1. Strain gauge
2. Moving contact

18. Inductance-Type
Pressure
Transducers
Linear Voltage Differential
Transducer (LVDT)

19. Reluctance-Type
Pressure
Transducers

20. Capacitive-Type
Pressure
Transducers

21. Piezoelectric
Pressure
Transducers

22. Photoelectric
Pressure
Transducers

23. Bridgman
gauge

24. Dead Weight Tester
 Dead weight tester is a primary standard for pressure measurement. It provides
god calibration facility over a wide pressure range.
𝑝 ∗ 𝑎 = 𝑀𝑔 + 𝐹𝑑