Raushankumar391 presentations

Atividades
Sobre

Resin tranfer moulding in composite materials

Há 3 semanas • 5 Visualizações

Python Basics

tusharpanda88 • Há 8 anos

Data science

Mohamed Loey • Há 7 anos

Abrasive water jet machining

sagar agarwal • Há 10 anos

Unconventional machining process basics

boopathi18 • Há 10 anos

Lecturer 1 machining

Er Pratip Roy • Há 9 anos

ECDM by Murli Kumbharkar

Murli Kumbharkar • Há 8 anos

ECM : Electrochemical machining - Principle,process,subsystems & applications

Pratik Chaudhari • Há 9 anos

Electrochemical Machining

AVINASH JURIANI • Há 7 anos

Electrochemical Machining (ECM)

RAVI KUMAR • Há 8 anos

Monte Carlo Simulations & Membrane Simulation and Dynamics

Arindam Ghosh • Há 7 anos

Phase-field modeling of crystal nucleation: Comparison with simulations and experiments

PFHub PFHub • Há 5 anos

Nucleation III: Phase-field crystal modeling of nucleation process

PFHub PFHub • Há 5 anos

Phase-field modeling of crystal nucleation II: Comparison with simulations and experiments

PFHub PFHub • Há 5 anos

Phase-field modeling of crystal nucleation I: Fundamentals and methods

PFHub PFHub • Há 5 anos

AZ31 presentation.pdf

FrankIss2 • Há 1 ano

Additive Manufacturing Simulation - Design and Process

Arindam Chakraborty, Ph.D., P.E. (CA, TX) • Há 6 anos

Comput Mater Sc Vol 34 (2005) 299 Pinning In C A

Dierk Raabe • Há 13 anos

Modelling Simul. Mater. Sci. Eng. 8 (2000) 445 C A And C P F E M

Dierk Raabe • Há 13 anos

Computational fluid dynamic simulations of solidification for enhancing speed of continuous cast copper

Rautomead Limited • Há 3 anos

mscThesisMathiasMul

Mathias Mul • Há 8 anos

Monte Carlo RX

Dierk Raabe • Há 13 anos

spparksUpdates

Justin Roberts • Há 8 anos

Microstructure prediction in cutting of Titanium

Hongtao Ding • Há 13 anos

Cellular automata : A simple Introduction

Adekunle Onaopepo • Há 9 anos

4. Diffusional Transformation.pptx

TruongDucQuang • Há 1 ano

1473407.ppt

Oswaldo Gonzales • Há 1 ano

CCT

MuneebRehman66 • Há 3 anos

TTT Diagram

AERONAUTICAL ENGINEERING at RTU • Há 8 anos

TTT diagram

SMALL ARMS FACTORY (MINISTRY OF DEFENSE) • Há 10 anos

Top 5 Skills for Project Managers

LinkedIn Learning Solutions • Há 8 anos

composite materials

Ver mais

RAUSHANKUMAR391

Apresentações

Resin tranfer moulding in composite materials

Gostaram

Python Basics

Data science

Abrasive water jet machining

Unconventional machining process basics

Lecturer 1 machining

ECDM by Murli Kumbharkar

ECM : Electrochemical machining - Principle,process,subsystems & applications

Electrochemical Machining

Electrochemical Machining (ECM)

Monte Carlo Simulations & Membrane Simulation and Dynamics

Phase-field modeling of crystal nucleation: Comparison with simulations and experiments

Nucleation III: Phase-field crystal modeling of nucleation process

Phase-field modeling of crystal nucleation II: Comparison with simulations and experiments

Phase-field modeling of crystal nucleation I: Fundamentals and methods

AZ31 presentation.pdf

Additive Manufacturing Simulation - Design and Process

Comput Mater Sc Vol 34 (2005) 299 Pinning In C A

Modelling Simul. Mater. Sci. Eng. 8 (2000) 445 C A And C P F E M

Computational fluid dynamic simulations of solidification for enhancing speed of continuous cast copper

mscThesisMathiasMul

Monte Carlo RX

spparksUpdates

Microstructure prediction in cutting of Titanium

Cellular automata : A simple Introduction

4. Diffusional Transformation.pptx

1473407.ppt

CCT

TTT Diagram

TTT diagram

Top 5 Skills for Project Managers