2. PrivateGSM Demo 1
Summary
1. Before you begin 2
1.1 Some advices... 2
1.2 ...and one tip 2
2. Activation...in 3 easy steps! 3
1 Install PrivateGSM 3
2 Launch the Connection Wizard 3
3 Launch the Configuration Wizard 4
3. How it works 5
1 Invite your contacts 5
2 Make a secure call using PrivateGSM 5
3 Receive a secure call using PrivateGSM 6
4 Call phases 7
5 Check your security 7
6 Receive Only mode 8
4. Contacts 9
Quick Start Guide
3. PrivateGSM Demo 2
1. Before you begin...
1.1 Some advices...
= Your phone calls’ security is granted by using the VoIP data line instead of the voice one.
Under particular events, due to the VoIP network condition, it could be present a little latency. In the
presence of a WiFi internet connection, consider to use it for a better communication quality.
= As a VoIP phone call, with data-packet exchanging, both the caller and the called pay for the calling.
To save your money consider to subscribe an unlimited mobile internet data plan with your mobile
operator.
= If you have an enterprise Blackberry, see with your IT department if you can install additional applica-
tions on it.
1.2 ...and one tip
= You can save in your address book the contacts to whom you want to make secure calls by adding the
secure prefix +801.
Quick Start Guide
4. PrivateGSM Demo 3
2. Activation...in 3 easy steps!
1 Install PrivateGSM
You can download PrivateGSM to your mobile from
http://www.privatewave.com
Just enter your mobile number; you will receive an
email/text message including a download link.
Click on the link to start downloading the PrivateGSM
installer.
Proceed by clicking on “Download”.
2 Launch the Connection Wizard
After the installation, in order to use PrivateGSM, you
have to set its internet connection through the Con-
nection Wizard. It automatically sets the network re-
gardless of any BlackBerry options or enterprise BES.
It is always possible to change the Mobile Transport
and APN (Access Point Network) data re-running the
Wizard, or, if you are an expert user, just selecting:
Settings >> Advanced Settings >> Connection
Settings
If the Wizard don’t work, select WiFi connection at the
end of the process.
Quick Start Guide
5. PrivateGSM Demo 4
3 Launch the Configuration Wizard
In order to start making phone calls, restart PrivateGSM
and choose Demo configuration. It will automatically
configure PrivateGSM Demo for your phone.
!
Manual configuration is reserved to Pri-
vateGSM for Enterprise VoIP Security
Suite only, because set PrivateGSM to
work with PrivateServer PBX.
Reboot the telephone to complete the installation.
Quick Start Guide
6. PrivateGSM Demo 5
3. How it works
1 Invite your contacts
Using your BlackBerry address book, you can invite
your contacts to join PrivateGSM.
Open PrivateGSM main menu, select “Invite others”
and choose the contacts to whom you want to make
secure calls. They will receive a text message includ-
ing the installation link.
Anyway, they can also download the software as de-
scribed in step 1.
2 Make a secure call using PrivateGSM
Calling with PrivateGSM is very easy; you only need to
add the secure prefix +801 before the number you
want to call.
!
Remember to use the number in the
international format, including the
country code:
+41 079 1234567
with PrivateGSM becomes:
+801 41 079 1234567
Quick Start Guide
7. PrivateGSM Demo 6
It is either possible to make a secure call through the
PrivateGSM menu. Select “Dial secure call”: your
address book will appear and you will just have to
select a name to activate a secure call.
!
To make a secure call, you and the called
party must be running PrivateGSM soft-
ware and be connected to the Internet.
3 Receive a secure call using PrivateGSM
Once PrivateGSM is installed and all the settings are
correctly configured on your mobile, you are able to
receive a secure call.
PrivateGSM displays an information note when an
incoming secure call is ringing on your phone. You
only need to press “OK” to allow the connection. The
system exchanges and verifies the security keys
and the conversation can start.
!
To receive a secure call, you must be run-
ning PrivateGSM software and be con-
nected to the Internet.
Quick Start Guide
8. PrivateGSM Demo 7
4 Call phases
To establish a call, PrivateGSM completes three phases, shown by three icons:
1. Red light: the connection is starting. This step may take several seconds.
2. Yellow light: ZRTP keys are being exchanged to secure the call.
3. Green light: secure call is established. Now it is possible to speak in a secure way.
5 Check your security
A PrivateGSM phone call is always encrypted.
To verify that there are no intrusions, after the call
connection the system displays at the bottom of the
screen a security code consisting of two random
words to both parties.
If both, you and your contact, see the same security
code then the call is secure. The security code is dif-
ferent each time you make or receive a secure call.
Quick Start Guide
9. PrivateGSM Demo 8
6 Receive Only mode
As the trial period expires, PrivateGSM turns in Re-
ceive Only mode.
In this mode PrivateGSM still allows you to receive
secure calls for as long as the software is installed on
your phone, but it’s no more possible to call other
PrivateGSM users.
Quick Start Guide
10. PrivateGSM Demo 9
4. Contacts
For additional help and more information, please visit the support section at:
http://www.privatewave.com
To contact our technical support:
Tel: +39 02 911 930 891
E-mail: support@privatewave.com
Office hours: Monday to Friday, 10.00 AM - 12.00 PM and 2.30 PM - 4.30 PM (GMT +1)
We remind you that the PrivateGSM Demo version is for evaluation purpose only, to show how the
software works. The full version on sale is part of the Enterprise VoIP Security Suite solution for fixed-
mobile encryption in a company network.
For more information or technical details on the Enterprise VoIP Security Suite, get in contact with
our sales team:
E-mail: sales@privatewave.com
Quick Start Guide