3. Introduction
• Hydroelectric power (hydropower) systems
convert the kinetic energy in flowing water
into electric energy.
• Falling or flowing water turns a propeller
like piece called a turbine.
• The turbine turns a metal shaft in an
electric generator which produces
electricity.
4.
5. Advantages
• No fuel required
• No air pollution
• Can easily work during high peak daily
loads
• Prevents floods
6. Disadvantages
• Disrupts the aquatic ecosystems
• Disruption of surrounding areas
• Requires large areas
• Large scale human displacement
7.
8. How a Hydroelectric Power System Works?
•Flowing water is
directed at a turbine.
•The flowing water
causes the turbine
to rotate, converting
the water’s kinetic
energy into
mechanical energy.
9. • The mechanical energy produced by the
turbine is converted into electric energy
using a turbine generator.
• Inside the generator, the shaft of the
turbine spins a magnet inside coils of
copper wire.
• It is a fact of nature that moving a magnet
near a conductor causes an electric
current.
10.
11. Hydel scheme
1 .Run-off Plants without Poundage:
As name indicates this type of plant doesn’t
store water, the plant uses as water comes.
2. Run-0ff plants with Poundage:
Poundage permits storage of water during the
off –peak period and use of this water during
peak periods.
3. Reservoir Plants: A reservoir plant is that
which has reservoir of such size as
to permit carrying over storage from wet season
to the next dry season.
12. 4 .Low head plants: In this case small dam is built
across the river to provide the necessary head.
In such plants Francis type of turbines are used.
5. Medium head plants: The fore bay provided at
the beginning of Penstock serves as water
reservoir for such plants. In these plants water
is generally carried out in open canals from
reservoir to the Fore bay and then to the
penstock.
13. 6. High head Plant: This plants works above
500mtrs and Pelton wheel turbines are
commonly used. In this plant water is carried out
from the main reservoir by a tunnel up to
surge tank and then from the surge tank to the
power house in penstock.
7. Base Load Plants: These Plants are mainly
depending on the nature of load. Is demand is
more, this plants are used regularly and load
factor of this plants are high.
14. 8. Peak load Plants: These plants are mainly
used during the peak load. Run-off river plants
with poundage can be used as peak-load plants.
reservoir plants with enough storage behind the
dam can be used either as base load or as peak
load plants as required.
9. Pumped storage plants: These plants are
used when quantity of water available for
generation is insufficient. If it is possible to pond
at head water and tail water locations after
passing through the turbine is stored in the tail
race pond from where it may be pumped back to
the Head water pond.
15. Low head plants
• In this case a small dam is built across the
river to provide the necessary head.
• The excess water is allowed to flow over
the dam itself.
• In such plants Francis, Propeller or Kaplan
types of turbines are used.
• Also no surge tank is required.
• These plants are constructed where the
water head available less then 30mtrs.
• The production of electricity will be less
due to low head.
16.
17. Medium head plants
• Mainly forebay provided before the
Penstock, acts as water reservoir for
medium head plants.
• In this plants mainly water is carried
through main reservoir to forebay and then
to the penstock.
• The forebay acts as surge tank for these
plants.
• The turbines used will be Francis type of
the steel encased variety.
18.
19. High head plants
• Mainly in these plants pressure tunnel is
provided before the surge tank, which
inturn connected to penstock.
• A pressure tunnel is taken off from the
reservoir and water brought to the valve
house at the start of the penstocks.
• The penstocks are huge steel pipes which
take large quantity of water from the valve
house to the power house.
20. • The valve house contains main sluice
gates and in addition automatic isolating
valves which come into operation when
the penstock bursts, cutting
further supply of water.
• Surge tank is an open tank and is built just
in between the beginning of the penstocks
and the valve house.
• In absence of surge tank, the water
hammer can damage the fixed gates.
21. • In Majority of dams Sluice gates are
provided.
• The sluice gates are opened when dam
level is below level and there is shortage
water for irrigation.
• Normally the high head plants are 500
meters above and for heads above 500
meters Pelton wheels are used.
22.
23. Components of hydel scheme
The principal components are:
1. Forebay
2. Intake structure
3. Penstocks
4. Surge tank
5. Turbines
6. Power house
7. Draft tube
8. Tail race
24.
25. Forebay
• Enlarged body of water provided in front of
penstock.
• Provided in case of run off river plants and
storage plants.
• Main function to store water which is
rejected by plant.
• Power house located closed to dam
penstock directly take water from
reservoir, reservoir act as forebay.
26.
27. Intake structure
• Water conveyed from forebay to
penstocks through intake structures.
• Main components are trash rack and gate.
• Trash rack prevent entry of debris.
28. Penstocks
• open or closed conduits which carry water
to the turbines.
• made of reinforced concrete or steel.
Concrete penstocks are suitable for low
heads less then 30mtrs.
• steel penstocks are designed for any
head.
• thickness of penstocks increases with
head or water pressure
29. • penstocks gates are fixed to initial of
penstocks, and flow of water is controlled
by operating penstock gates.
• Either buried in ground or kept exposed.
30. Surge tank
• additional storage for near to
turbine, usually provided in high head
plants.
• located near the beginning of the
penstock.
• As the load on the turbine decreases or
during load rejection by the turbine the
surge tank provides space for holding
water.
31. • surge tank over comes the
abnormal pressure
in the conduit when load on the turbine falls
and acts as a reservoir during increase of
load on the turbine.
32. Turbines
• turbines are used to convert the energy water of
falling water into mechanical energy.
• water turbine is a rotary engine that takes energy from
moving water.
• flowing water is directed on to the blades of a turbine
runner, creating a force on the
33. • Since the runner is spinning, the force acts
through a distance n this way, energy is
transferred from the water flow to the
turbine.
• The principal types of turbines are:
1) Impulse turbine
2) Reaction Turbine
34. Impulse turbines: mainly used in high head
plants.
• the entire pressure of water is converted into
kinetic energy in a nozzle and the velocity of
the jet drives the blades of turbine.
• The nozzle consist of a needle, and quantity
of water jet falling on the turbine is controlled
this needle placed in the tip of the nozzle.
• If the load on the turbine decreases, the
governor pushes the needle into the
nozzle, thereby reducing the quantity of water
striking the turbine.
35. • Examples of Impulse turbines are:
• Pelton Wheel.
• Turgo
• Michell-Banki (also known as the Cross
flow or Ossberger turbine.
36.
37. Reaction turbines : are mainly for low and
medium head plants.
• In reaction turbine the water enters the runner
partly with pressure energy and partly with
velocity head.
• Most water turbines in use are reaction turbines
and are used in low (<30m/98 ft) and medium
(30-300m/98–984 ft)head applications.
• In reaction turbine pressure drop occurs in both
fixed and moving blades.
38. • In this turbine the runner blades changed
with respect to guide vane opening.
• As the sudden decrease of load takes
place, the guide vane limit decreases
according to that runner blade closes.
• Examples of reaction turbines are:
Francis turbine
Kaplan turbine
39. Draft tube
• is a pipe or passage of gradually
increasing cross sectional area, which
connect to the exit to tail race.
• it reduces high velocity of water
discharged by the turbine.
• draft tube permits turbines to be installed
at a higher level than the tail race
level, which help the maintaince and repair
of turbines.
40.
41. Power house
• Power house contains the electro
mechanical equipment i.e. hydro power
turbine, Generator, excitation
system, main inlet
valves, transformers, Switchyard, DC
systems, governor, bus duct, step up
transformers, step down
transformers, high voltages switch
gears, control metering for protection of
systems.
42. Tail race
• tail race tunnel or channel are provided to
direct the used water coming out of draft
tube back to the river.
• important criteria of designing the tail race
is kind of draft tube, the gross head and
geographical situation of the area.
• Tail race is designed in such a way that
water hammer is minimizes when water
leaves the draft tube.
43.
44. The amount of electricity that can be generated by a
hydropower plant depends on two factors:
•flow rate - the quantity of water flowing in a given
time; and
• head - the height from which the water falls.
The greater the flow and head, the more electricity
produced.
Flow Rate = the quantity of water flowing
Head = the height from which water falls
Power generation