1. CURRICULUM VITAE
PRESENT ADDRESS
Jagadeesh.Rowtu
C/o Satyanarayana.D
Hno:12-5-91/2,
S.P Nagar,
Hyderabad-500018
E-mail: jagadeesh.rowtu@gmail.com
Contact no:+91-9160690720
OBJECTIVES:
To work in an organization, where I can apply the best of my knowledge in the progressive department of
the organizations and improvement in my knowledge and skills.
Education Qualification :
B.Tech in Electrical & Electronics Engineering
WORK EXPERIENCE:
TOTAL EXPERIENCE :4.8 yrs.
1. Currently working as a Design and Planning Engineer in Sterling and Wilson ltd Hyderabad. (From
July-2013 To till present).
2. Previously worked Design Engineer in swapna Enterprises, Hyderabad. ( From Sep-2010 To June-
2013 )
Projects worked in Experience:
1) Johnson and Johnson Blue mountain project 33kv Switch yard and internal electrical layouts
preparation in Hyderabad.
2) Western construction 33Kv four pole structure and internal electrical works in Hyderabad.
3) Coca cola beverages pvt ltd project in Hyderabad
4) Alexandria phase-I and Phase-II&III projects.
5) Mars international india pvt ltd and Laurs labs pvt ltd projects in Visakhapatnam.
6) 132kv switchyard and EPC works for TCS Adibatla campus. Hyderabad.
7) Designing of Internal and External power flow for TCS Aibatla campus. Hyderabad.
8) Hyderabad Metro Rail -Admin building and stations Electrification.
9) 33kv Substation and internal and external electrical design for ICICI bank main head office
building in Hyderabad.
10) Internal and External Electrical works for ESI Multi specialty hospital in Hyderabad.
11) 33kv substation and SLDs and Internal Electrical Design for Hospira Health Care India PVt ltd,
Visakhapatnam.
12) TAJ GVK,PARK hotel,T rident & Oberoi Hotels in Hyderabad.
13) Raheja IT Park, Accenture IT Park, TCS park in Hyderabad.
14) NACIL airport in samshabad, Andhrapradesh.
15) HPCL project in vishakapatnam.
16) GMR Vemagiri power plant.
17) TIDC ,Chain manufacturing plant & ITC Paper plant Electrification, Badrachalam.
18) 33 kv Substation for KJSH power plant in Barbil, Orissa.
19) Kadapa Airport electrical works
20) 50 MW solar power plant for Atachampet Mahaboob Nagar,Telangana.
21) 5 MW Solar power plant in Pulivendula, Welspun,Andhra Pradesh.
22) 1 MW Solar power plant in Jaya Bharath, Andhra Pradesh.
23) 14 MW Solar power plant for Aditya Birla, Andhra Pradesh
24) NSPl solar power plant in Ananthapur Andhrapradesh.
25) 33kv substation and building electrification for Indian nation centre of ocean information serviced
main building in pragathinagar,Hyderabad.
26) Air force navil housing board 33 kv Main substation and RMUs and 5 internal substation works
2. 27) A star hospitals and Raghavendra hospitals electrical design works and HT works for incoming
supply.
28) Dr Reddys laboratory electrical design works as per CEIG norms and approval from the CEIG.
Tendering projects:
1)worked for the tendering of 132kv switchyard in vishakapatnam port project for Client of Vedanta
ltd.scope including of designing ,commissioning erection of 132/6.6 kv & 6.6/415volts transformer main pcc
panels ,capacitor banks and other switchyard accessories.
2)worked for tendering of 132 kv switchyard in upcoming project or BARC in Vishakapatnam,Checking the
vendor equipments specifications of transformer,Current and potential transformers,circuit breakers of SF6
and vaccum,Neutral grounding resistors ,chemical earthing pits,panels ,capacitor banks,lighting fixtures.
Extracting the quantity of GI rods ,earthing strips, ACSR conductors, ISMC Steel structures ..etc.
3)CAIRN ENERGY INDIA LTD:
Worked for the tendering project of oil refinery plant in Rajasthan, consist of GIS and 33kv and 11kv
switchgears and transformers ,cabling and UPS.
4)Working for costing , quotations from vendor, price negotiating with vendor, submitting the tender
,attended pre bid meeting, discussing with project coordinators .
DETAILED EDUCATIONAL QUALIFICATION:
Course with
specialization
Name of the Board Year of Passing
Percentage of
marks
S.S..C. Z.P.H.SCHOOL 2004 77.8%
TWELTH STD
VJR COLLAGE
2006 83.7%
B. Tech Electrical and
Electronics Eng.
JAWAHARLAL NEHRU
TECHNOLOGICAL UNIVERSITY
HYDERABAD
2010 63.4%
COMPUTER KNOWLEDGE:
• Packages : ePLAN, Auto CAD 2010 MEP ,creating 3D views, ABS ( AutoCAD Building System)
MS OFFICE, DIALUX.
• Operating systems: Windows 95 & 98, XP Professional.
NATURE OF Working Presently:
1. 33 kv substation drawings and CT&PT selections and metering cubical selection and four
structuring drawings preparation and approval from the CEIG for Johnson and Johnson project
2. Preparing the outdoor & indoor switch yard layout for 132kv ,33kv substation & 11kv
substations.sizing of indoor & outdoor breakers, relay panels ,lightning arrestors, foundation
details for the transformers, poles ,breakers, panels.
3. Sizing of Transformers ,NGR ,HT Panels ,HT breakers & HT cables ,RTCC panels, PV module
selection, array size , string & DC cable sizing, Invertors sizing DC load calculation.
4. Designing of Four, Three & two pole structure for outdoor substations. Preparing substation
layouts & trench layouts.
5. Designing of Single line diagrams, meeting the various requirements of the Electrical system
and also as per the specification guidelines.
6. Designing of RMU, Metering equipment’s consisting Tri vector meters, CT & PT classes and
burden’s. Relays suitable closing of breakers during fault conditions.
3. 7. Designing the PLC panels for substation equipments (i.e Transformers ,MV & LT panels
,capacitor banks ) automation. designing control cable for the PLC O/P & I/P from the panel
breakers .checking the architecture diagram for PLC system. preparing the control cable
schedule for substations.
8. Preparing the battery sizing calculation for the battery back up power in the substations by
calculating the breakers spring charge motor, tripping coil, closing coil momentary peak load
factors.providing power pack in the panels.
9. Choosing the cable sizes as per the required load after derating factor & as per short circuit
capacity., voltage drop calculations.
10. Sizing the UPS as per the require load, designing the UPS output panels with double neutral
busbars to avoid overheating due to the harmonics, choosing the double sized phase cables for
neutral, sizing the sure arrestor in the panels . Choosing the cable sizes as per the required
load after derating factor & as per short circuit capacity., voltage drop
11. Designing of Bus bar sizes & Rising main bus bars sizes as per the required load & voltage
drop ,short circuit calculations. preparing the layouts for bus bars arrangement & fixing
details.from transformer to panels & raising mains in the shafts.
12. Supporting the tendering team for quantity extractions. for steel ,light fixtures sockets, cables,
breakers ,dry type transformers ,metering equipments, wiring quantities.
13. Design of lighting for the whole building or factory using IS specified lux levels or as per the
specifications. using CG LUX & DIALUX software for finding the required light fixtures in
room /hall as per the required lux levels. preparing lighting layouts.
14. Support for HVAC by choosing the power and control cable sizes ,Earthing strips for the
AHU,CHILLERS ,CSU & motors.
15. Designing the Lighting protection system for various type of Buildings as per IS standards.
16. Designing of Earthing systems for all the equipments in the buildings as per the IS standards
calculating the earthing strip and cables as per the short circuiting capacity of panels
,specialized for UPS , labs, Electronic earthing. Preparing the Earthing schematic for the
electrical system consisting Tripod earthing ,dedicative UPS earthing.
17. Designing of cable tray layouts and routing cable's, calculating the required size of cable trays.
18. Ordering for the manufacturing LV panels & approving the vendor drawings .
19. Design the lv systems fire alarm, arrangement of audio system wiring & TV wiring, lv s in the
hotels using the basic concept from client/consultant.
20. Indulging in co ordination with other MEP services such as HVAC,FIRE FIGHTING , IT TRAYS &
RACEWAYS , BAGGAGE HANDLING ,TILES & FALSE CEILING CONTRACTORS.
21. Skilled in Preparing 3D modeling drawing in AutoCAD 2007,2008,2013 versions ,well known to
prepare the isometric views of objects or equipments. known to extract the quantity using
2009 AUTOCAD for Electrical objects such as cable trays, conduits , sockets , light, panels ..etc
Indulged in site activities.
1. Working with site team for preparation of Variation BOQ of exceeding & non tendering items
quantities.
4. 2. Assisting in preparing Running Bills ,creating SR’s & technical clarifications .
3. Support to site execution team for updating design as per site conditions and providing guidance in
case of site installation issues.
4. Partially involving in Testing activities with Commissioning team for Testing of HT panels,
Transformers and LT panels and cables.
5. Lead in the preparation of As built drawings for the projects.
Personal Skills:
1. Comprehensive in doing the job with good result in the given time, ability to deal with people.
2. Diplomatically, willingness to learn, team facilitator
Hobbies:
1) Planting Trees, Agriculture.
PERSONAL PROFILE:
Name : Jagadeesh.R
Father's Name : Satyam Naidu.R
Date of Birth : 10th
March-1988
Sex : Male.
Marital Status : Single
Nationality : Indian.
Language Known : English, Hindi, Telugu.
DECLARATION
I hereby declare that the Particulars given by me are true to the best of my knowledge and
belief.
Place: Hyderabad
Date: 15/06/2015
Yours faithfully
(Jagadeesh R)