SlideShare uma empresa Scribd logo
1 de 56
Baixar para ler offline
Shafts and Shafts Components
Hussein Basma
Lebanese American University
Please note that this presentation is totally based on “Shigley’s
Mechanical Engineering Design Book” as the only used
reference including all the definitions, examples and details.
Introduction about shafts
Shaft materials.
Shaft layout
Shaft design for stress
Deflection consideration
Critical Speeds for shafts
Miscellaneous Shaft Components
Limits and fits
Outline
Introduction
 Shafts are different than axels.
 Shafts are rotating members, usually of circular cross section.
 Axels are nonrotating members analyzed as static beams.
 Shafts are used to transmit power or motion.
 They are essential part in many machine designs.
 Material selection.
 Geometric layout.
 Stress and strength
static strength
fatigue strength.
 Deflection and rigidity
 Vibration due to natural frequency
What to examine about shafts?
Shaft Materials
 Deflection is affected by stiffness not strength.
 Stiffness is related to the modulus of elasticity, thus the
material.
 Modulus of elasticity is constant for all steels, thus material
decisions will not control rigidity.
 Rigidity will be controlled only by geometric decisions.
Shaft Layout
 The design of the shafts does not follow a certain rule.
 It depends mainly on the application.
 Certain conventions to follow in shaft design:
-Avoid long shafts to minimize deflection
-Support the loads between bearings
-Avoid using more than two bearings.
Shaft Layout
 In many shaft applications the aim is to transmit torque from
one gear to another gear or pulley.
 The shaft must be sized to support the torsional stress and
deflection.
 To transmit this torque certain torque-transfer elements are
used such as:
 Torque transmission
Keys
splines
setscrews
pins
Tapered fits
Shrink fits
Shaft Design for Stress
 Locate the critical locations along the shaft.
 Critical locations are on the outer surface where bending
moment is large, torque is present and stress concentrations
exist.
 Bending moment is determined by shear and bending
moment diagrams. (1 or more planes could be needed)
 A steady bending moment will produce a completely
reversed moment on rotating shaft (σ 𝑚 =0)
 Axial stresses can be neglected.
 Critical Locations
Shaft Design for Stress
 Shaft stresses
 We will deal with bending, torsion and axial stresses as
midrange and alternating components.
 For analysis it is appropriate to combine the different stresses
into alternating and midrange von Mises stresses
(again we can neglect axial stresses):
Shaft Design for Stress
 P.S: For ductile materials the use of the stress-concentration
factors is sometimes optional.
Shaft Design for Stress
 Now we can take the acquired von Mises stresses and use
these values in any of the known fatigue failure criteria to
evaluate the factor of safety n or, for design purposes, the
diameter d.
 Reminder of the fatigue failure criteria:
 DE-Goodman
 DE-Gerber
 DE-ASME Elliptic
 DE-Soderberg
Shaft Design for Stress
 DE-Goodman
 Plugging in the values of the von Mises stresses will yield the
following equations, one solved for n and one for d :
 DE-Gerber
 DE-ASME Elliptic
 DE-Soderberg
 For rotating shafts with constant bending and torsion, the
bending stress is completely reversed and the torsion is
steady. ( )
 We should always consider the possibility of static failure in
the first load cycle. ( check for yielding)
 The ASME Elliptic criteria takes yield into account but it is
not entirely conservative.
Shaft Design for Stress
 For this purpose a von Mises maximum stress is calculated:
Shaft Design for Stress
 To check for yielding, we compare the maximum stress to
the yield strength:
Shaft Design for Stress
 Example:
At a machined shaft shoulder the small diameter d is 28 mm, the
large diameter D is 42 mm, and the fillet radius is 2.8 mm. The
bending moment is 142.4 N.m and the steady torsion moment is
124.3 N.m. The heat-treated steel shaft has an ultimate strength of
𝑆 𝑢𝑡 =735 MPa and a yield strength of 𝑆 𝑦 = 574 MPa. Our
reliability goal is 0.99.
(a) Determine the fatigue factor of safety of the design using each
of the fatigue failure criteria described in this section.
(b) Determine the yielding factor of safety.
Shaft Design for Stress
At a machined shaft shoulder the small diameter d is 28
mm, the large diameter D is 42 mm, and the fillet radius
is 2.8 mm. The bending moment is 142.4 N.m and the
steady torsion moment is 124.3 N.m. The heat-treated
steel shaft has an ultimate strength of 𝑆 𝑢𝑡 =735 MPa and
a yield strength of 𝑆 𝑦 = 574 MPa. Our reliability goal is
0.99
Shaft Design for Stress
(a) D/d = 42/28 = 1.50, r/d 2.8/28= 0.10, 𝐾𝑡 = 1.68 (Fig. A–15–9).
𝐾𝑡𝑠 = 1.42 (Fig. A–15–8), q = 0.85 (Fig. 6–20), 𝑞 𝑠ℎ𝑒𝑎𝑟 = 0.92
(Fig. 6–21).
From Eq. (6–32), 𝐾𝑓 = 1 + 0.85(1.68 − 1) = 1.58
𝐾𝑓𝑠 = 1 + 0.92(1.42 − 1) = 1.39
Eq. (6–8) : 𝑆 𝑒’ = 0.5(735) = 367.5 MPa
Eq. (6–19): 𝑘 𝑎 =4.51(735)−0.265
Eq. (6–20): 𝑘 𝑏 =(
28
7.62
)−0.107
𝑘 𝑐= 𝑘 𝑑 = 𝑘 𝑓 =1
 Solution:
Shaft Design for Stress
 Solution:
Table 6–6: 𝑘 𝑒 = 0.814
𝑆 𝑒 =0.787(0.870)0.814(367.5) = 205MPa
For a rotating shaft, the constant bending moment will create a
completely reversed
bending stress.
𝑀 𝑎= 142.4 N. m 𝑇 𝑚 = 124.3 N.m 𝑀 𝑚= 𝑇𝑎= 0
Applying Eq. (7–7) for the DE-Goodman criteria gives:
1
𝑛
=
16
𝜋(0.028)3{
[4 1.58× 142.4 2]
1
2
205× 106 +
[3 1.39× 124.3 2]
1
2
735× 106 }= 0.615
n=1.62
 Similarly, plugging the values of the mean and amplitude of
the torque and bending moment in the equations of the different
failure criteria, we get:
 P.S: Note that the safety factor calculated using Soderberg
relation is the smallest one since this criteria is the most
conservative one.
(b) To calculate the yielding safety factor, we use:
σ′max= [
32×1.58×142.4
𝜋 0.028 3
2
+ 3
16×1.39×124.3
𝜋 0.028 3
2
]
1
2 = 125.4 MPa
𝑛 𝑦 =
574
125.4
= 4.85
Shaft Design for Stress
 The stress concentration zones are mainly due to bearings,
gears fillets and change in shaft geometry or radius.
 The stress concentration factor 𝐾𝑡depends on the type of
bearing or gear.
 Figs. A-15-16 and A-15-17 give values of the concentration
factors of flat-bottomed grooves
 Table 7-1 gives the typical stress-concentration factors for the
first iteration in the design of a shaft.
 Estimating Stress Concentration:
Deflection Consideration
 As we mentioned earlier, we need to know the complete shaft
geometry before we can perform deflection analysis.
 Therefore we should design the dimensions at critical locations
to handle the stresses and estimate the other dimensions.
 Once the complete geometry is known, we can perform the
deflection analysis.
 Deflection should be checked at gears and bearing supports.
 Chapter 4 deals with the methods used to calculate deflection,
including singularity functions and numerical integration.
Deflection Consideration
 For certain shafts of complex geometries we may need three
dimensional analysis and then use superposition to calculate the
overall deflection.
 Deflection analysis is straight forward, but it incorporates long
procedures and tedious steps.
 This can be simplified by using certain three dimensional
deflection analysis software.
Deflection Consideration
 Table 7-2 includes the maximum allowable deflection for
different types of bearings and gears.
Deflection Consideration
 Where 𝑦 𝑎𝑙𝑙 is the allowable deflection and 𝑛 𝑑 is the design
safety factor.
 After calculating the deflection and slope in the shaft, we
compare it with the allowable values provided by the different
tables.
 Sometimes, if the calculated deflection is greater than the
allowable values, changes in dimensions must be considered
and the diameter of the shaft must be changed according to this
equation:
 The preceding equation can be applied on the slope as well:
Deflection Consideration
 Where (𝑠𝑙𝑜𝑝𝑒) 𝑎𝑙𝑙 is the allowable slope.
Deflection Consideration
 Shearing deflections are usually 1% of the bending deflections
and are usually ignored.
 In cases of short shafts, where 𝑙
𝑑 <10 , shearing deflections
become important.
 The angular deflection is represented by:
 For constant torque through a homogeneous material:
Critical Speeds of Shafts
 A common problem encountered when dealing with rotating
shafts is the problem of critical speeds.
 At certain speeds, when the frequency of rotation becomes close
to the shaft’s natural frequency, the shaft becomes unstable with
increasing deflections that may lead to failure.
 For simple geometries, as a simply supported, constant-diameter
shaft, the first critical speed can be estimated using the following
equation:
where m the mass per unit length, γ is the specific weight.
Critical Speeds of Shafts
 For an ensemble of attachments, Rayleigh’s method for lumped
masses gives:
where 𝑤𝑖 is the weight of the ith location and 𝑦𝑖 is the
deflection at the ith body
 At this stage, we will define something called the influence
coefficients.
 An Influence coefficient is the transverse deflection at location i
on a shaft due to a unit load at location j on the shaft.
 For a simply supported beams with a single unit load, the
influence coefficients are given by:
Critical Speeds of Shafts
Critical Speeds of Shafts
Critical Speeds of Shafts
 Assume three loads, the influence coefficients can be expressed:
 From the influence coefficients we can calculate the deflections
𝑦1, 𝑦2 and 𝑦3 as follows:
 The force 𝐹𝑖 arises from weights attached or centrifugal forces
𝑚𝑖 ω2 𝑦𝑖. The equation can be expressed as:
Critical Speeds of Shafts
 Solving for the roots of this system will yield the following
relation:
Critical Speeds of Shafts
 If we had one mass 𝑚1, the critical speed denoted by ω11 will
be expressed as
1
ω11
2 = 𝑚1 𝛿11
 Similarly,
1
ω22
2 = 𝑚2 𝛿22 and
1
ω33
2 = 𝑚3 𝛿33
 Then the equation can be expressed as:

1
ω1
2 ≫
1
ω2
2 +
1
ω3
2 since ω1 is way smaller than ω2 and ω3
Critical Speeds of Shafts
 This will simplify to:
 The preceding equation can be extended to n-body shafts:
 This equation is known as the Dunkerley’s equation.
 Principle of superposition:
Critical Speeds of Shafts
 This principle includes calculating an equivalent load placed on
the center of the shaft. In other words, we transform each load
into an equivalent load placed at the center denoted by the
subscript c.
 This equivalent load can be found from:
Critical Speeds of Shafts
 The critical speed ω 1 can be calculated after summing the
equivalent load of each load on the shaft:
Critical Speeds of Shafts
 Example:
Consider a simply supported steel shaft , with 25 mm diameter
and a 775 mm span between bearings, carrying two gears weighing
175 and 275 N.
(a) Find the influence coefficients.
(b) Find 𝑤𝑦 and 𝑤𝑦2 and the first critical speed using
Rayleigh’s equation.
(c) From the influence coefficients, find ω11 and ω22.
(d) Using Dunkerley’s equation, estimate the first critical speed.
(e) Use superposition to estimate the first critical speed.
Critical Speeds of Shafts
 Solution:
a) I =
πd4
64
=
π(25)4
64
= 19175 𝑚𝑚4
6E Il = 6(207000)(19175)(775)= 18.5× 1012 N.𝑚𝑚3
Critical Speeds of Shafts
δ11=
600(175)(7752−6002−1752)
18.5×1012 = 0.00119 𝑚𝑚
𝑁
δ12= δ21=
275(175)(7752−2752−1752)
18.5×1012 = 0.00129 𝑚𝑚
𝑁
δ22=
275(500)(7752−2752−5002)
18.5×1012 = 0.00204 𝑚𝑚
𝑁
b) 𝑦1= 𝑤1δ11+ 𝑤2δ12 = (175)(0.00119) + (275)(0.00129)= 0.56 mm
𝑦2= 𝑤1δ21+ 𝑤2δ22 = (175)(0.00129) + (275)(0.00204)= 0.79 mm
Critical Speeds of Shafts
b) 𝑤𝑦 = 175(0.56)+275(0.79) = 315.3 N.mm
𝑤𝑦2= 175 (0.56)2+ 275(0.79)2= 226.5 N.𝑚𝑚2
Using Rayleigh’s equation,
ω =
9.81(315.3)×10−3
226.5×10−6 = 117 rad/s
c)
1
ω11
2 = 𝑚1 𝛿11, and 𝑚1=
𝑤1
𝑔
, then:
1
ω11
2 =
𝑤1
𝑔
𝛿11=
175×0.00119×10−3
9.81
1
ω22
2 = 𝑚2 𝛿22, and 𝑚2=
𝑤2
𝑔
, then:
1
ω22
2 =
𝑤2
𝑔
𝛿22=
275×0.00204×10−3
9.81
ω11= 217 rad/s
ω22= 132 rad/s
d) Using Dunkerley’s equation:
Critical Speeds of Shafts
1
ω1
2 =
1
2172 +
1
1322 = 7.863× 10−5
Implies, ω1=113 rad/s
e) Using superposition:
δ 𝑐𝑐=
b𝑐x 𝑐(𝑙2−b𝑐𝑐
2
−x 𝑐𝑐
2
)
18.5×1012
=
387.5 387.5 7752−387.52−387.52
18.5×1012
= 0.00244 mm/N
𝑤1𝑐 =
175(0.00119)
0.00244
= 85.3 N
𝑤2𝑐 =
275(0.00204)
0.00244
= 229.9 N
Then, ω =
𝑔
δ 𝑐𝑐 𝑤 𝑖𝑐
=
9.81
0.00244(85.3+229.9)10−3 = 112.9 𝑟𝑎𝑑/𝑠
Critical Speeds of Shafts
Critical Speeds of Shafts
Method Rayleigh Dunkerly Superposition
First Critical Speed 117 rad/sec 113 rad/sec 112.9 rad / sec
Since designers seek first critical speed at
least twice the operating speed, so the
difference has no effect on our design.
The critical speed calculated by Dunkerley and
Superposition methods are always expected to
be less than Rayleigh’s method because they
neglected the effect of the other critical speeds
Shafts and Shafts Components

Mais conteúdo relacionado

Mais procurados (20)

Basic of Brakes,
Basic of Brakes, Basic of Brakes,
Basic of Brakes,
 
Gear train
Gear trainGear train
Gear train
 
3 shaft stress in shafts
3 shaft   stress in shafts3 shaft   stress in shafts
3 shaft stress in shafts
 
Module 4 gears
Module 4 gearsModule 4 gears
Module 4 gears
 
Unit 5 threaded joint
Unit 5 threaded jointUnit 5 threaded joint
Unit 5 threaded joint
 
Design of bearing
Design of bearingDesign of bearing
Design of bearing
 
1 static failure theories ductile r1
1 static failure theories ductile r11 static failure theories ductile r1
1 static failure theories ductile r1
 
Bearing and Sliding contact bearings
Bearing and Sliding contact bearingsBearing and Sliding contact bearings
Bearing and Sliding contact bearings
 
Unit 3.2 Design of Clutches
Unit 3.2 Design of ClutchesUnit 3.2 Design of Clutches
Unit 3.2 Design of Clutches
 
Bearing
BearingBearing
Bearing
 
Types of springs Design Machine Elements (DME)
Types of springs Design Machine Elements (DME)Types of springs Design Machine Elements (DME)
Types of springs Design Machine Elements (DME)
 
Design of shafts couplings ppt
Design of shafts couplings  pptDesign of shafts couplings  ppt
Design of shafts couplings ppt
 
Introduction to Gears
Introduction to GearsIntroduction to Gears
Introduction to Gears
 
Springs - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-IISprings - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-II
 
Bevel gears
Bevel gearsBevel gears
Bevel gears
 
Gearbox design - MECH 393 final project
Gearbox design - MECH 393 final projectGearbox design - MECH 393 final project
Gearbox design - MECH 393 final project
 
Shafts and its components lecture
Shafts and its components lectureShafts and its components lecture
Shafts and its components lecture
 
DYNAMICS OF MACHINES UNIT-1 BY Mr.P.RAMACHANDRAN/AP/MECH/KIT/CBE
DYNAMICS OF MACHINES UNIT-1 BY Mr.P.RAMACHANDRAN/AP/MECH/KIT/CBEDYNAMICS OF MACHINES UNIT-1 BY Mr.P.RAMACHANDRAN/AP/MECH/KIT/CBE
DYNAMICS OF MACHINES UNIT-1 BY Mr.P.RAMACHANDRAN/AP/MECH/KIT/CBE
 
Sliding contact bearing
Sliding contact bearing Sliding contact bearing
Sliding contact bearing
 
Gear trains
Gear trainsGear trains
Gear trains
 

Destaque

Shaft design2 Erdi Karaçal Mechanical Engineer University of Gaziantep
Shaft design2 Erdi Karaçal Mechanical Engineer University of GaziantepShaft design2 Erdi Karaçal Mechanical Engineer University of Gaziantep
Shaft design2 Erdi Karaçal Mechanical Engineer University of GaziantepErdi Karaçal
 
BASIC MECHANICAL ENGINEERING
BASIC MECHANICAL ENGINEERINGBASIC MECHANICAL ENGINEERING
BASIC MECHANICAL ENGINEERINGNAGorao SURNER
 

Destaque (6)

Unit 2 design of shaft
Unit 2 design of shaftUnit 2 design of shaft
Unit 2 design of shaft
 
Shaft design2 Erdi Karaçal Mechanical Engineer University of Gaziantep
Shaft design2 Erdi Karaçal Mechanical Engineer University of GaziantepShaft design2 Erdi Karaçal Mechanical Engineer University of Gaziantep
Shaft design2 Erdi Karaçal Mechanical Engineer University of Gaziantep
 
Shaft
ShaftShaft
Shaft
 
selection of material
selection of materialselection of material
selection of material
 
Shaft & Torsion
Shaft & TorsionShaft & Torsion
Shaft & Torsion
 
BASIC MECHANICAL ENGINEERING
BASIC MECHANICAL ENGINEERINGBASIC MECHANICAL ENGINEERING
BASIC MECHANICAL ENGINEERING
 

Semelhante a Shafts and Shafts Components

CHAPTER 1.ppt
CHAPTER 1.pptCHAPTER 1.ppt
CHAPTER 1.pptJani Jai
 
Shear force and bending moment
Shear force and bending momentShear force and bending moment
Shear force and bending momenttalha022
 
Ch 10 slides_m
Ch 10 slides_mCh 10 slides_m
Ch 10 slides_mmiladshah
 
SPRING Design & Design parameters details
SPRING Design & Design parameters detailsSPRING Design & Design parameters details
SPRING Design & Design parameters detailsDeepakRamachandra2
 
Unit_4_Design Agains Fluctuation load.ppt
Unit_4_Design Agains Fluctuation load.pptUnit_4_Design Agains Fluctuation load.ppt
Unit_4_Design Agains Fluctuation load.pptDrSomnathKolgiri
 
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKE
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKEA REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKE
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKEJournal For Research
 
Unit 3 design against fluctuation load
Unit 3 design against fluctuation loadUnit 3 design against fluctuation load
Unit 3 design against fluctuation loadSomnath Kolgiri
 
8 principal stresses
8 principal stresses8 principal stresses
8 principal stressesMohamed Yaser
 
IRJET- Investigation of Stresses in Rear Half Axle of an Automobile
IRJET- Investigation of Stresses in Rear Half Axle of an AutomobileIRJET- Investigation of Stresses in Rear Half Axle of an Automobile
IRJET- Investigation of Stresses in Rear Half Axle of an AutomobileIRJET Journal
 
Chapter 6 column
Chapter 6   columnChapter 6   column
Chapter 6 columnSimon Foo
 
DESIGN AGAINST FLUCTUATING LOAD
DESIGN AGAINST FLUCTUATING LOADDESIGN AGAINST FLUCTUATING LOAD
DESIGN AGAINST FLUCTUATING LOADPriyank Gandhi
 
Performance Optimization of Tie rod using FEA
Performance Optimization of Tie rod using FEAPerformance Optimization of Tie rod using FEA
Performance Optimization of Tie rod using FEAIJERD Editor
 
Design of bearing.pptx
Design of bearing.pptxDesign of bearing.pptx
Design of bearing.pptxssuserf66787
 

Semelhante a Shafts and Shafts Components (20)

CHAPTER 1.ppt
CHAPTER 1.pptCHAPTER 1.ppt
CHAPTER 1.ppt
 
shafts.pdf
shafts.pdfshafts.pdf
shafts.pdf
 
Shear force and bending moment
Shear force and bending momentShear force and bending moment
Shear force and bending moment
 
Ch 10 slides_m
Ch 10 slides_mCh 10 slides_m
Ch 10 slides_m
 
SPRING Design & Design parameters details
SPRING Design & Design parameters detailsSPRING Design & Design parameters details
SPRING Design & Design parameters details
 
Graduation project presentation
Graduation project presentationGraduation project presentation
Graduation project presentation
 
5 beams
5 beams5 beams
5 beams
 
5 Beams[1]
5 Beams[1]5 Beams[1]
5 Beams[1]
 
3 torsion
3 torsion3 torsion
3 torsion
 
Unit_4_Design Agains Fluctuation load.ppt
Unit_4_Design Agains Fluctuation load.pptUnit_4_Design Agains Fluctuation load.ppt
Unit_4_Design Agains Fluctuation load.ppt
 
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKE
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKEA REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKE
A REVIEW ON HELICAL COMPRESSION SPRING TO DESIGN A SHOCK ABSORBER OF BIKE
 
Unit 3 design against fluctuation load
Unit 3 design against fluctuation loadUnit 3 design against fluctuation load
Unit 3 design against fluctuation load
 
8 principal stresses
8 principal stresses8 principal stresses
8 principal stresses
 
IRJET- Investigation of Stresses in Rear Half Axle of an Automobile
IRJET- Investigation of Stresses in Rear Half Axle of an AutomobileIRJET- Investigation of Stresses in Rear Half Axle of an Automobile
IRJET- Investigation of Stresses in Rear Half Axle of an Automobile
 
Staircase Design Report
Staircase Design ReportStaircase Design Report
Staircase Design Report
 
Chapter 6 column
Chapter 6   columnChapter 6   column
Chapter 6 column
 
99999599.pptx
99999599.pptx99999599.pptx
99999599.pptx
 
DESIGN AGAINST FLUCTUATING LOAD
DESIGN AGAINST FLUCTUATING LOADDESIGN AGAINST FLUCTUATING LOAD
DESIGN AGAINST FLUCTUATING LOAD
 
Performance Optimization of Tie rod using FEA
Performance Optimization of Tie rod using FEAPerformance Optimization of Tie rod using FEA
Performance Optimization of Tie rod using FEA
 
Design of bearing.pptx
Design of bearing.pptxDesign of bearing.pptx
Design of bearing.pptx
 

Último

UNIT-V FMM.HYDRAULIC TURBINE - Construction and working
UNIT-V FMM.HYDRAULIC TURBINE - Construction and workingUNIT-V FMM.HYDRAULIC TURBINE - Construction and working
UNIT-V FMM.HYDRAULIC TURBINE - Construction and workingrknatarajan
 
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Call Girls in Nagpur High Profile
 
result management system report for college project
result management system report for college projectresult management system report for college project
result management system report for college projectTonystark477637
 
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur Escorts
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur EscortsCall Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur Escorts
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur EscortsCall Girls in Nagpur High Profile
 
Online banking management system project.pdf
Online banking management system project.pdfOnline banking management system project.pdf
Online banking management system project.pdfKamal Acharya
 
Glass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesGlass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesPrabhanshu Chaturvedi
 
UNIT-III FMM. DIMENSIONAL ANALYSIS
UNIT-III FMM.        DIMENSIONAL ANALYSISUNIT-III FMM.        DIMENSIONAL ANALYSIS
UNIT-III FMM. DIMENSIONAL ANALYSISrknatarajan
 
Introduction to Multiple Access Protocol.pptx
Introduction to Multiple Access Protocol.pptxIntroduction to Multiple Access Protocol.pptx
Introduction to Multiple Access Protocol.pptxupamatechverse
 
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...ranjana rawat
 
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...ranjana rawat
 
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...ranjana rawat
 
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLS
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLSMANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLS
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLSSIVASHANKAR N
 
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur EscortsHigh Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur EscortsCall Girls in Nagpur High Profile
 
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service Nashik
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service NashikCall Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service Nashik
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service NashikCall Girls in Nagpur High Profile
 
Java Programming :Event Handling(Types of Events)
Java Programming :Event Handling(Types of Events)Java Programming :Event Handling(Types of Events)
Java Programming :Event Handling(Types of Events)simmis5
 
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...ranjana rawat
 
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...ranjana rawat
 
Booking open Available Pune Call Girls Pargaon 6297143586 Call Hot Indian Gi...
Booking open Available Pune Call Girls Pargaon  6297143586 Call Hot Indian Gi...Booking open Available Pune Call Girls Pargaon  6297143586 Call Hot Indian Gi...
Booking open Available Pune Call Girls Pargaon 6297143586 Call Hot Indian Gi...Call Girls in Nagpur High Profile
 
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur Escorts
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur EscortsCall Girls in Nagpur Suman Call 7001035870 Meet With Nagpur Escorts
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur EscortsCall Girls in Nagpur High Profile
 

Último (20)

UNIT-V FMM.HYDRAULIC TURBINE - Construction and working
UNIT-V FMM.HYDRAULIC TURBINE - Construction and workingUNIT-V FMM.HYDRAULIC TURBINE - Construction and working
UNIT-V FMM.HYDRAULIC TURBINE - Construction and working
 
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...Top Rated  Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
Top Rated Pune Call Girls Budhwar Peth ⟟ 6297143586 ⟟ Call Me For Genuine Se...
 
result management system report for college project
result management system report for college projectresult management system report for college project
result management system report for college project
 
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur Escorts
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur EscortsCall Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur Escorts
Call Girls Service Nagpur Tanvi Call 7001035870 Meet With Nagpur Escorts
 
Online banking management system project.pdf
Online banking management system project.pdfOnline banking management system project.pdf
Online banking management system project.pdf
 
Glass Ceramics: Processing and Properties
Glass Ceramics: Processing and PropertiesGlass Ceramics: Processing and Properties
Glass Ceramics: Processing and Properties
 
UNIT-III FMM. DIMENSIONAL ANALYSIS
UNIT-III FMM.        DIMENSIONAL ANALYSISUNIT-III FMM.        DIMENSIONAL ANALYSIS
UNIT-III FMM. DIMENSIONAL ANALYSIS
 
Introduction to Multiple Access Protocol.pptx
Introduction to Multiple Access Protocol.pptxIntroduction to Multiple Access Protocol.pptx
Introduction to Multiple Access Protocol.pptx
 
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(PRIYA) Rajgurunagar Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
 
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...
(SHREYA) Chakan Call Girls Just Call 7001035870 [ Cash on Delivery ] Pune Esc...
 
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
The Most Attractive Pune Call Girls Budhwar Peth 8250192130 Will You Miss Thi...
 
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLS
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLSMANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLS
MANUFACTURING PROCESS-II UNIT-5 NC MACHINE TOOLS
 
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur EscortsHigh Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
High Profile Call Girls Nagpur Meera Call 7001035870 Meet With Nagpur Escorts
 
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service Nashik
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service NashikCall Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service Nashik
Call Girls Service Nashik Vaishnavi 7001305949 Independent Escort Service Nashik
 
Java Programming :Event Handling(Types of Events)
Java Programming :Event Handling(Types of Events)Java Programming :Event Handling(Types of Events)
Java Programming :Event Handling(Types of Events)
 
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
 
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
(ANVI) Koregaon Park Call Girls Just Call 7001035870 [ Cash on Delivery ] Pun...
 
Booking open Available Pune Call Girls Pargaon 6297143586 Call Hot Indian Gi...
Booking open Available Pune Call Girls Pargaon  6297143586 Call Hot Indian Gi...Booking open Available Pune Call Girls Pargaon  6297143586 Call Hot Indian Gi...
Booking open Available Pune Call Girls Pargaon 6297143586 Call Hot Indian Gi...
 
Water Industry Process Automation & Control Monthly - April 2024
Water Industry Process Automation & Control Monthly - April 2024Water Industry Process Automation & Control Monthly - April 2024
Water Industry Process Automation & Control Monthly - April 2024
 
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur Escorts
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur EscortsCall Girls in Nagpur Suman Call 7001035870 Meet With Nagpur Escorts
Call Girls in Nagpur Suman Call 7001035870 Meet With Nagpur Escorts
 

Shafts and Shafts Components

  • 1. Shafts and Shafts Components Hussein Basma Lebanese American University Please note that this presentation is totally based on “Shigley’s Mechanical Engineering Design Book” as the only used reference including all the definitions, examples and details.
  • 2. Introduction about shafts Shaft materials. Shaft layout Shaft design for stress Deflection consideration Critical Speeds for shafts Miscellaneous Shaft Components Limits and fits Outline
  • 3. Introduction  Shafts are different than axels.  Shafts are rotating members, usually of circular cross section.  Axels are nonrotating members analyzed as static beams.  Shafts are used to transmit power or motion.  They are essential part in many machine designs.
  • 4.  Material selection.  Geometric layout.  Stress and strength static strength fatigue strength.  Deflection and rigidity  Vibration due to natural frequency What to examine about shafts?
  • 5. Shaft Materials  Deflection is affected by stiffness not strength.  Stiffness is related to the modulus of elasticity, thus the material.  Modulus of elasticity is constant for all steels, thus material decisions will not control rigidity.  Rigidity will be controlled only by geometric decisions.
  • 6. Shaft Layout  The design of the shafts does not follow a certain rule.  It depends mainly on the application.  Certain conventions to follow in shaft design: -Avoid long shafts to minimize deflection -Support the loads between bearings -Avoid using more than two bearings.
  • 7. Shaft Layout  In many shaft applications the aim is to transmit torque from one gear to another gear or pulley.  The shaft must be sized to support the torsional stress and deflection.  To transmit this torque certain torque-transfer elements are used such as:  Torque transmission
  • 11. pins
  • 14. Shaft Design for Stress  Locate the critical locations along the shaft.  Critical locations are on the outer surface where bending moment is large, torque is present and stress concentrations exist.  Bending moment is determined by shear and bending moment diagrams. (1 or more planes could be needed)  A steady bending moment will produce a completely reversed moment on rotating shaft (σ 𝑚 =0)  Axial stresses can be neglected.  Critical Locations
  • 15. Shaft Design for Stress  Shaft stresses  We will deal with bending, torsion and axial stresses as midrange and alternating components.
  • 16.  For analysis it is appropriate to combine the different stresses into alternating and midrange von Mises stresses (again we can neglect axial stresses): Shaft Design for Stress  P.S: For ductile materials the use of the stress-concentration factors is sometimes optional.
  • 17. Shaft Design for Stress  Now we can take the acquired von Mises stresses and use these values in any of the known fatigue failure criteria to evaluate the factor of safety n or, for design purposes, the diameter d.  Reminder of the fatigue failure criteria:  DE-Goodman  DE-Gerber  DE-ASME Elliptic  DE-Soderberg
  • 19.  DE-Goodman  Plugging in the values of the von Mises stresses will yield the following equations, one solved for n and one for d :
  • 23.  For rotating shafts with constant bending and torsion, the bending stress is completely reversed and the torsion is steady. ( )  We should always consider the possibility of static failure in the first load cycle. ( check for yielding)  The ASME Elliptic criteria takes yield into account but it is not entirely conservative. Shaft Design for Stress
  • 24.  For this purpose a von Mises maximum stress is calculated: Shaft Design for Stress  To check for yielding, we compare the maximum stress to the yield strength:
  • 25. Shaft Design for Stress  Example: At a machined shaft shoulder the small diameter d is 28 mm, the large diameter D is 42 mm, and the fillet radius is 2.8 mm. The bending moment is 142.4 N.m and the steady torsion moment is 124.3 N.m. The heat-treated steel shaft has an ultimate strength of 𝑆 𝑢𝑡 =735 MPa and a yield strength of 𝑆 𝑦 = 574 MPa. Our reliability goal is 0.99. (a) Determine the fatigue factor of safety of the design using each of the fatigue failure criteria described in this section. (b) Determine the yielding factor of safety.
  • 26. Shaft Design for Stress At a machined shaft shoulder the small diameter d is 28 mm, the large diameter D is 42 mm, and the fillet radius is 2.8 mm. The bending moment is 142.4 N.m and the steady torsion moment is 124.3 N.m. The heat-treated steel shaft has an ultimate strength of 𝑆 𝑢𝑡 =735 MPa and a yield strength of 𝑆 𝑦 = 574 MPa. Our reliability goal is 0.99
  • 27. Shaft Design for Stress (a) D/d = 42/28 = 1.50, r/d 2.8/28= 0.10, 𝐾𝑡 = 1.68 (Fig. A–15–9). 𝐾𝑡𝑠 = 1.42 (Fig. A–15–8), q = 0.85 (Fig. 6–20), 𝑞 𝑠ℎ𝑒𝑎𝑟 = 0.92 (Fig. 6–21). From Eq. (6–32), 𝐾𝑓 = 1 + 0.85(1.68 − 1) = 1.58 𝐾𝑓𝑠 = 1 + 0.92(1.42 − 1) = 1.39 Eq. (6–8) : 𝑆 𝑒’ = 0.5(735) = 367.5 MPa Eq. (6–19): 𝑘 𝑎 =4.51(735)−0.265 Eq. (6–20): 𝑘 𝑏 =( 28 7.62 )−0.107 𝑘 𝑐= 𝑘 𝑑 = 𝑘 𝑓 =1  Solution:
  • 28. Shaft Design for Stress  Solution: Table 6–6: 𝑘 𝑒 = 0.814 𝑆 𝑒 =0.787(0.870)0.814(367.5) = 205MPa For a rotating shaft, the constant bending moment will create a completely reversed bending stress. 𝑀 𝑎= 142.4 N. m 𝑇 𝑚 = 124.3 N.m 𝑀 𝑚= 𝑇𝑎= 0
  • 29. Applying Eq. (7–7) for the DE-Goodman criteria gives: 1 𝑛 = 16 𝜋(0.028)3{ [4 1.58× 142.4 2] 1 2 205× 106 + [3 1.39× 124.3 2] 1 2 735× 106 }= 0.615 n=1.62
  • 30.  Similarly, plugging the values of the mean and amplitude of the torque and bending moment in the equations of the different failure criteria, we get:  P.S: Note that the safety factor calculated using Soderberg relation is the smallest one since this criteria is the most conservative one.
  • 31. (b) To calculate the yielding safety factor, we use: σ′max= [ 32×1.58×142.4 𝜋 0.028 3 2 + 3 16×1.39×124.3 𝜋 0.028 3 2 ] 1 2 = 125.4 MPa 𝑛 𝑦 = 574 125.4 = 4.85
  • 32. Shaft Design for Stress  The stress concentration zones are mainly due to bearings, gears fillets and change in shaft geometry or radius.  The stress concentration factor 𝐾𝑡depends on the type of bearing or gear.  Figs. A-15-16 and A-15-17 give values of the concentration factors of flat-bottomed grooves  Table 7-1 gives the typical stress-concentration factors for the first iteration in the design of a shaft.  Estimating Stress Concentration:
  • 33. Deflection Consideration  As we mentioned earlier, we need to know the complete shaft geometry before we can perform deflection analysis.  Therefore we should design the dimensions at critical locations to handle the stresses and estimate the other dimensions.  Once the complete geometry is known, we can perform the deflection analysis.  Deflection should be checked at gears and bearing supports.  Chapter 4 deals with the methods used to calculate deflection, including singularity functions and numerical integration.
  • 34. Deflection Consideration  For certain shafts of complex geometries we may need three dimensional analysis and then use superposition to calculate the overall deflection.  Deflection analysis is straight forward, but it incorporates long procedures and tedious steps.  This can be simplified by using certain three dimensional deflection analysis software.
  • 35. Deflection Consideration  Table 7-2 includes the maximum allowable deflection for different types of bearings and gears.
  • 36. Deflection Consideration  Where 𝑦 𝑎𝑙𝑙 is the allowable deflection and 𝑛 𝑑 is the design safety factor.  After calculating the deflection and slope in the shaft, we compare it with the allowable values provided by the different tables.  Sometimes, if the calculated deflection is greater than the allowable values, changes in dimensions must be considered and the diameter of the shaft must be changed according to this equation:
  • 37.  The preceding equation can be applied on the slope as well: Deflection Consideration  Where (𝑠𝑙𝑜𝑝𝑒) 𝑎𝑙𝑙 is the allowable slope.
  • 38. Deflection Consideration  Shearing deflections are usually 1% of the bending deflections and are usually ignored.  In cases of short shafts, where 𝑙 𝑑 <10 , shearing deflections become important.  The angular deflection is represented by:  For constant torque through a homogeneous material:
  • 39. Critical Speeds of Shafts  A common problem encountered when dealing with rotating shafts is the problem of critical speeds.  At certain speeds, when the frequency of rotation becomes close to the shaft’s natural frequency, the shaft becomes unstable with increasing deflections that may lead to failure.  For simple geometries, as a simply supported, constant-diameter shaft, the first critical speed can be estimated using the following equation: where m the mass per unit length, γ is the specific weight.
  • 40. Critical Speeds of Shafts  For an ensemble of attachments, Rayleigh’s method for lumped masses gives: where 𝑤𝑖 is the weight of the ith location and 𝑦𝑖 is the deflection at the ith body
  • 41.  At this stage, we will define something called the influence coefficients.  An Influence coefficient is the transverse deflection at location i on a shaft due to a unit load at location j on the shaft.  For a simply supported beams with a single unit load, the influence coefficients are given by: Critical Speeds of Shafts
  • 43. Critical Speeds of Shafts  Assume three loads, the influence coefficients can be expressed:  From the influence coefficients we can calculate the deflections 𝑦1, 𝑦2 and 𝑦3 as follows:
  • 44.  The force 𝐹𝑖 arises from weights attached or centrifugal forces 𝑚𝑖 ω2 𝑦𝑖. The equation can be expressed as: Critical Speeds of Shafts  Solving for the roots of this system will yield the following relation:
  • 45. Critical Speeds of Shafts  If we had one mass 𝑚1, the critical speed denoted by ω11 will be expressed as 1 ω11 2 = 𝑚1 𝛿11  Similarly, 1 ω22 2 = 𝑚2 𝛿22 and 1 ω33 2 = 𝑚3 𝛿33  Then the equation can be expressed as:  1 ω1 2 ≫ 1 ω2 2 + 1 ω3 2 since ω1 is way smaller than ω2 and ω3
  • 46. Critical Speeds of Shafts  This will simplify to:  The preceding equation can be extended to n-body shafts:  This equation is known as the Dunkerley’s equation.
  • 47.  Principle of superposition: Critical Speeds of Shafts  This principle includes calculating an equivalent load placed on the center of the shaft. In other words, we transform each load into an equivalent load placed at the center denoted by the subscript c.  This equivalent load can be found from:
  • 48. Critical Speeds of Shafts  The critical speed ω 1 can be calculated after summing the equivalent load of each load on the shaft:
  • 49. Critical Speeds of Shafts  Example: Consider a simply supported steel shaft , with 25 mm diameter and a 775 mm span between bearings, carrying two gears weighing 175 and 275 N. (a) Find the influence coefficients. (b) Find 𝑤𝑦 and 𝑤𝑦2 and the first critical speed using Rayleigh’s equation. (c) From the influence coefficients, find ω11 and ω22. (d) Using Dunkerley’s equation, estimate the first critical speed. (e) Use superposition to estimate the first critical speed.
  • 50. Critical Speeds of Shafts  Solution: a) I = πd4 64 = π(25)4 64 = 19175 𝑚𝑚4 6E Il = 6(207000)(19175)(775)= 18.5× 1012 N.𝑚𝑚3
  • 51. Critical Speeds of Shafts δ11= 600(175)(7752−6002−1752) 18.5×1012 = 0.00119 𝑚𝑚 𝑁 δ12= δ21= 275(175)(7752−2752−1752) 18.5×1012 = 0.00129 𝑚𝑚 𝑁 δ22= 275(500)(7752−2752−5002) 18.5×1012 = 0.00204 𝑚𝑚 𝑁 b) 𝑦1= 𝑤1δ11+ 𝑤2δ12 = (175)(0.00119) + (275)(0.00129)= 0.56 mm 𝑦2= 𝑤1δ21+ 𝑤2δ22 = (175)(0.00129) + (275)(0.00204)= 0.79 mm
  • 52. Critical Speeds of Shafts b) 𝑤𝑦 = 175(0.56)+275(0.79) = 315.3 N.mm 𝑤𝑦2= 175 (0.56)2+ 275(0.79)2= 226.5 N.𝑚𝑚2 Using Rayleigh’s equation, ω = 9.81(315.3)×10−3 226.5×10−6 = 117 rad/s c) 1 ω11 2 = 𝑚1 𝛿11, and 𝑚1= 𝑤1 𝑔 , then: 1 ω11 2 = 𝑤1 𝑔 𝛿11= 175×0.00119×10−3 9.81 1 ω22 2 = 𝑚2 𝛿22, and 𝑚2= 𝑤2 𝑔 , then: 1 ω22 2 = 𝑤2 𝑔 𝛿22= 275×0.00204×10−3 9.81 ω11= 217 rad/s ω22= 132 rad/s
  • 53. d) Using Dunkerley’s equation: Critical Speeds of Shafts 1 ω1 2 = 1 2172 + 1 1322 = 7.863× 10−5 Implies, ω1=113 rad/s e) Using superposition: δ 𝑐𝑐= b𝑐x 𝑐(𝑙2−b𝑐𝑐 2 −x 𝑐𝑐 2 ) 18.5×1012 = 387.5 387.5 7752−387.52−387.52 18.5×1012 = 0.00244 mm/N
  • 54. 𝑤1𝑐 = 175(0.00119) 0.00244 = 85.3 N 𝑤2𝑐 = 275(0.00204) 0.00244 = 229.9 N Then, ω = 𝑔 δ 𝑐𝑐 𝑤 𝑖𝑐 = 9.81 0.00244(85.3+229.9)10−3 = 112.9 𝑟𝑎𝑑/𝑠 Critical Speeds of Shafts
  • 55. Critical Speeds of Shafts Method Rayleigh Dunkerly Superposition First Critical Speed 117 rad/sec 113 rad/sec 112.9 rad / sec Since designers seek first critical speed at least twice the operating speed, so the difference has no effect on our design. The critical speed calculated by Dunkerley and Superposition methods are always expected to be less than Rayleigh’s method because they neglected the effect of the other critical speeds