1. XJ LAMPS 8L - 1
LAMPS
CONTENTS
page page
REMOVAL AND INSTALLATION FRONT TURN SIGNAL . ................... 2
BACKUP, REAR TURN SIGNAL, TAILLIGHT AND HEADLIGHTS . . . . . . . ................... 1
REAR FOG LIGHT . . . . . . . . . . . . . . . . . . . . . 2 SIDE REPEATER LIGHT .................. 1
CENTER HIGH MOUNTED STOPLIGHT . . . . . . . 2 SPECIFICATIONS
FRONT FOG LAMP . . . . . . . . . . . . . . . . . . . . . . 2 REPLACEMENT BULBS ................... 3
FRONT POSITION LIGHT . . . . . . . . . . . . . . . . . 1
REMOVAL AND INSTALLATION SIDE REPEATER LIGHT
HEADLIGHTS REMOVAL
1. Insert a small, flat bladed pry tool in slot pro-
REMOVAL vided at the bottom side of the side repeater lamp
1. Remove the 2 screws holding the bezel in place bulb to socket.
and remove bezel (Fig. 1). 2. Pry lamp lens from lamp housing.
2. Remove the 4 screws holding the headlight and 3. Rotate and pull the bulb from the socket (Fig.
replace the bulb from the rear of the housing (Fig. 2). 3).
Fig. 1 Headlight Bezel Fig. 3 Side Repeater Light
INSTALLATION INSTALLATION
1. Align the side repeater lamp bulb to the socket
(Fig. 3).
2. Push and twist the bulb into the socket.
3. Position the top edge of the lamp lens to the lip
on the lamp housing.
4. Press downward until the lamp lens is fully
seated to the lip.
5. Verify lamp operation.
FRONT POSITION LIGHT
REMOVAL
1. Remove the 2 screws holding the headlight
bezel in place and remove the bezel (Fig. 1).
Fig. 2 Headlight Housing
2. Remove the 4 screws holding the headlight
1. Reverse the removal procedures to install. housing (Fig. 2).
2. 8L - 2 LAMPS XJ
REMOVAL AND INSTALLATION (Continued)
3. Pull the front position light socket from the rub- 3. Remove the lamp element from the housing
ber grommet and replace the bulb (Fig. 4). (Fig. 6).
Fig. 4 Front Position Light Fig. 6 Front Fog Light
INSTALLATION INSTALLATION
1. Reverse the removal procedure for installation. 1. Install the new lamp element in the housing
and reinstall the lower housing.
FRONT TURN SIGNAL
BACKUP, REAR TURN SIGNAL, TAILLIGHT AND
REMOVAL REAR FOG LIGHT
1. Remove the 2 screws holding the bezel in place
and remove the bezel (Fig. 1). REMOVAL
2. Remove the screws holding the turn signal 1. There are 3 mounting bolts attaching the tail-
housing in place (Fig. 5). light assembly. When removing, unfasten the 3 bolts
3. Remove the turn signal housing. located on the top and side. Do not remove the bot-
4. Twist the socket from the back of the turn sig- tom shoulder bolt; lift up and out to remove the
nal housing and then pull from the socket. assembly.
2. Turn the bulb assembly 1/3 turn and pull the
bulb from the socket to replace the bulb (Fig. 7).
Fig. 5 Front Turn Signal Bulb
INSTALLATION
1. Reverse the removal procedure to install. Fig. 7 Rear Lamp Replacement
INSTALLATION
FRONT FOG LAMP 1. Reverse the removal procedure to install.
REMOVAL CENTER HIGH MOUNTED STOPLIGHT
1. Remove the 2 screws from the bottom cover of
the lamp body (Fig. 5). REMOVAL
2. Disconnect the 2 wires from the lamp element. 1. Remove the 2 screws (Fig. 8).
2. Rotate the bulb sockets 1/4 turn and pull from
the housing.
