Mais conteúdo relacionado Semelhante a Understanding RF Fundamentals and the Radio Design of Wireless Networks (20) Mais de Cisco Mobility (20) Understanding RF Fundamentals and the Radio Design of Wireless Networks1. Understanding RF
Fundamentals and the Radio
Design of Wireless Networks
Fred Niehaus
Technical Marketing Engineer WNBU
BRKEWN-3016
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 1
2. Session Abstract
This advanced session focuses on the deep-dive
understanding of the often overlooked Radio Frequency
part of the design and deployment of a Wireless LAN
Network. It discusses 802.11 Radio, MIMO, Access
Points and antenna placements, when to use a DAS
system, antenna patterns…
It covers the main environments such as carpeted
offices, campuses and conference centers, and it
provides feedback based on lessons learned from
challenging deployments such as outdoor/stadium/rail
deployments and manufacturing areas.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 2
3. Session Agenda – Objectives
• What is radio how did we get here?
• Basic 802.11 Radio Hardware & Terminology
• 802.11 Antenna Basics – Single & Diversity Antennas
• Interpreting antenna patterns – Cisco Richfield Facility
• Diversity, Multipath, 802.11n RF characteristics
• DAS (Distributed Antenna Systems) overview
• Choosing the right Access Point
• Survey Tools
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 3
4. What We Won’t Be Covering
• Wireless Security
• Clean-air (separate session for that)
• WIDS/WIPS (Wireless Intrusion Prevention Service)
• High density deployments (separate session for that)
• LBS (Location Base Services)
• Walled garden, captive portals
• WLAN management
• 802.11n beyond RF characteristics
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 4
5. What Is Radio?
How Did We End Up on These Frequencies?
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 5
6. Basic Understanding of Radio…
AC Frequency 60 Hz
or 60 CPS – Cycles
Per Second
Waves travel back and forth
Battery is DC Typical home is AC so fast they leave the wire
Direct Current Alternating Current
Popular Radio Frequencies:
How fast the AC current goes is its ―frequency‖ AM Radio 1100 kHz (1.100 MHz)
AC is very low frequency 60 Hz (Cycles Per Second)
Shortwave 3-30 MHz
Radio waves are measured in kHz, MHz and GHz FM Radio 88-108 MHz
Weather Radio 162.40 MHz
The lower the frequency the physically longer the radio Cellular Phones 800-900 MHz
wave – Higher frequencies have much shorter waves as Wi-Fi 802.11b/g 2.4 GHz
such take more power to move them greater distances. Wi-Fi 802.11a 5 GHz
This is why 2.4 GHz goes further then 5 GHz
(given same amount of RF power) Vintage RF
Transmitter
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 6
7. A Radio Needs a Proper Antenna
As the frequency
goes up the radiating
element gets smaller
Cisco antennas are Omni-Directional antennas Directional antennas like this
like the one on the left, ―Patch‖ antenna radiate
identified by color
radiate much like forward like placing tin foil
Blue indicates 5 GHz a raw light bulb would behind the light bulb or tilting
Black indicates 2.4 GHz everywhere in all directions the lamp shade
Antennas are custom made for the Note: Same RF energy is
frequency to be used. Some antennas used but results in greater
range as its focused at the
have two elements to allow for both cost of other coverage areas
frequencies in one antenna housing
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 7
8. Complex Modulation Schemes
Radio technology has a lot in
common with that old twisted pair
phone line that started out at 300
baud and then quickly increased
In order to get faster data rates,
(throughput) into the radio signal,
complex modulation schemes as
QPSK or 64 bit QAM is used.
Generally speaking, the faster the
data rate the more powerful signal
Example of 802.11n Modulation Coding Schemes
needs to be at the receiver to be
QAM or Quadrature Amplitude Modulation is one decoded.
of the fastest modulation types actually sending
two signals that are out of phase with each other Take-away here is that 802.11n is a
and then somehow ―putting all the pieces back method of using special modulation
together‖ for even greater throughput. techniques and *not* specific to a
frequency like 2.4 or 5 GHz
This is one of the advantages of 802.11n
802.11n can be used in either band
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 8
9. The Radio Spectrum in the US
Source US Department of Commerce
http://www.ntia.doc.gov/osmhome/allochrt.PDF
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 9
10. Wi-Fi Radio Spectrum
The first frequencies
available for Wi-Fi use
was in the 2.4 GHz range
As Wi-Fi popularity and
usage increased the FCC
allocated additional
spectrum in the 5 GHz
band.
2.4 GHz 5 GHz The spectrum we use
today is also used by
Wi-Fi is ―unlicensed‖ so it doesn’t show up in Amateur (Ham Radio) and
the overall spectrum allocation as a service other services such as
radio location (radar).
But it has beginnings in the ISM (industrial
There is more bandwidth
Scientific Medical) band where it was not in 5 GHz and mechanisms
desirable or profitable to license such short are in place to co-exist
range devices. with services such as
radar
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 10
11. Wi-Fi Radio Spectrum The 2.4 GHz spectrum has
only 3 non-overlapping
channels 1,6 and 11 (US)
There are plenty of
channels in the 5 GHz
spectrum and they do not
overlap
2.4 GHz and 5 GHz are
different portions of the
radio band and usually
require separate antennas
Most if not all 5 GHz
Even today many portable devices in use are limited to 2.4 devices also have support
GHz only including newer devices but this is changing for 2.4 GHz however there
are still many 2.4 GHz only
802.11b/g is 2.4 GHz
802.11a is 5 GHz devices.
802.11n (can be either band) 2.4 or 5 GHz
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 11
12. Basic 802.11 RF Terminology
Hardware Identification
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 12
13. Common RF terms
• Attenuation – a loss in force or intensity – As radio waves travel in media such as coaxial cable attenuation occurs.
• BER – Bit Error Rate - the fraction of bits transmitted that are received incorrectly.
• Channel Bonding – act of combining more than one channel for additional bandwidth
• dBd – abbreviation for the gain of an antenna system relative to a dipole
• dBi – abbreviation for the gain of an antenna system relative to an isotropic antenna
• dBm – decibels milliwatt -- abbreviation for the power ratio in decibels (dB) of the measured power referenced to one milliwatt of
transmitted RF power.
• Isotropic antenna – theoretical ―ideal‖ antenna used as a reference for expressing power in logarithmic form.
• MRC – Maximal Ratio Combining a method that combines signals from multiple antennas taking into account factors such as
signal to noise ratio to decode the signal with the best possible Bit Error Rate.
• Multipath – refers to a reflected signal that combines with a true signal resulting in a weaker or some cases a stronger signal.
• mW – milliwatt a unit of power equal to one thousandth of a watt (usually converted to dBm)
• Noise Floor – The measure of the signal created from the sum of all the noise sources and unwanted signals appearing at the
receiver. This can be adjacent signals, weak signals in the background that don’t go away, electrical noise from electromechanical
devices etc.
• Receiver Sensitivity – The minimum received power needed to successfully decode a radio signal with an acceptable BER. This
is usually expressed in a negative number depending on the data rate. For example the AP-1140 Access Point requires an RF
strength of at least negative -91 dBm at 1 MB and an even higher strength higher RF power -79 dBm to decode 54 MB
• Receiver Noise Figure – The internal noise present in the receiver with no antenna present (thermal noise).
• SNR – Signal to Noise Ratio – The ratio of the transmitted power from the AP to the ambient (noise floor) energy present.
• TxBF – Transmit beam forming the ability to transmit independent and separately encoded data signals, so-called streams, from
each of the multiple transmit antennas
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 13
14. Identifying RF Connectors
RP-TNC Connector ―RP-SMA‖ Connector
Used on most Cisco Access Points Used on some Linksys Products
―N‖ Connector ―SMA‖ Connector
Used on the 1520 Mesh and 1400 Bridge ―Pig tail‖ type cable assemblies
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 14
15. Identifying Different Cable Types
LMR- 400 Foil & shield
LMR – 1200
Leaky Coax
shield cut away on one side ½ inch Heliax (Hardline)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 15
16. Antenna Cables – LMR Series
This is a chart depicting
different types of Times
Microwave LMR Series
coaxial cable.
Cisco uses Times
Microwave cable and has
standardized on two types:
Cisco Low Loss (LMR-400)
and Cisco Ultra Low Loss
(LMR-600).
LMR-600 is recommended
when longer cable distances
are required
Larger cables can be used
but connectors are difficult
to find and install
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 16
17. Antenna Cables
LMR-400 is 3/8 inch Cisco Low Loss
LMR-600 is ½ inch Cisco Ultra Low Loss
Trivia: LMR Stands for Land Mobile Radio
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 17
18. Antenna Cables – Plenum
Plenum is the air-handling
space that is found above
drop ceiling tiles or below
floors.
Because of fire
regulations this type of
cable must burn with low
smoke
The 3 Ft white cable
attached to most Cisco
antennas is plenum rated.
Our outdoor cable (black)
is not Plenum
If the cable is ORANGE in color it is usually Plenum cable is more
Plenum Rated. expensive
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 18
20. Antenna Basics
• Antenna - a device which radiates and/or receives radio signals
• Antennas are usually designed to operate at a specific frequency
Wide-Band antennas can support additional frequencies but it’s a
trade-off and usually not with the same type of performance.
• Antenna Gain is characterized using dBd or dBi
Antenna gain can be measured in decibels against a reference antenna
called a dipole and the unit of measure is dBd (d for dipole)
Antenna gain can be measured in decibels against a computer modeled
antenna called an ―isotropic‖ dipole <ideal antenna> and the unit of measure
is dBi (i for isotropic dipole) (computer modeled ideal antenna)
• WiFi antennas are typically rated in dBi.
dBi is a HIGHER value (marketing folks like higher numbers)
Conventional radio (Public safety) tend to use a dBd rating.
To convert dBd to dBi simply add 2.14 so a 3 dBd = 5.14 dBi
Again… dBd is decibel dipole, dBi is decibel isotropic.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 20
21. How Does a Omni-Directional Dipole Radiate?
The radio signal leaves the center wire using the ground wire
(shield) as a counterpoise to radiate in a 360 degree pattern
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 21
22. Antenna Theory (Dipole & Monopole)
Dipole Monopole
A Monopole requires a
ground plane – (conductive
surface)
A dipole does not require a
ground plane as the bottom half
is the ground (counterpoise). 808 Ft Broadcast Monopole
WSM 650 AM (erected in 1932)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 22
23. Antenna Theory (Dipole & Monopole)
Monopoles were added to our
antenna line primarily for aesthetics
and require a metal surface to radiate
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 23
24. How Does a Directional Antenna Radiate?
Although you don’t get additional RF power with a directional antenna it does
concentrate the available energy into a given direction resulting in greater range
much like bringing a flashlight into focus.
Also a receive benefit - by listening in a given direction, this can limit the
reception of unwanted signals (interference) from other directions for better
performance
A dipole called the ―driven element‖ is placed in front of other elements.
This motivates the signal to go forward into a given direction for gain.
(Inside view of the Cisco AIR-ANT1949 13.5 dBi Yagi)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 24
25. Patch Antenna a Look Inside
Patch antennas can have multiple radiating elements that
combine for gain. Sometimes a metal plate is used behind the
antenna as a reflector for more gain
9.5 dBi Patch, AIR-ANT5195-R
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 25
26. Antennas Identified by Color
Black indicates 2.4 GHz
Blue indicates 5 GHz
Orange indicates 2.4 & 5 GHz
Orange indicates
2.4 & 5 GHz
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 26
27. Most Common 2.4 GHz Antennas
for Access Points (Single and Diversity)
Antenna Description
AIR-ANT4941
2.2 dBi Swivel-mount Dipole; most popular
mounts directly to radio, low gain, indoor
AIR-ANT5959
2 dBi Diversity Ceiling-mount Omni
AIR-ANT1729
6 dBi Wall-mount Patch
AIR-ANT1728
5.2 dBi Ceiling-mount Omni
AIR-ANT3549
9 dBi Wall-mount Patch
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 27
28. Most Common 5 GHz Antennas
for Access Points (Single and Diversity)
Antenna Description
AIR-ANT5135D-R
3.5 dBi Omni-directional Antenna; mounts directly to radio, low
gain, indoor
AIR-ANT5145V-R
4.5 dBi Omni-directional Diversity Antenna; unobtrusive, ceiling
mount, low gain, indoor
AIR-ANT5160V-R
6 dBi Omni-directional Antenna; ceiling or mast mount,
indoor/outdoor
AIR-ANT5170P-R
7 dBi Patch Diversity Antenna;
directional, small profile, wall mount, indoor/outdoor
AIR-ANT5195-R
9.5 dBi Patch Antenna;
directional, small profile, wall mount, indoor/outdoor
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 28
30. Understanding Antenna Patterns
Dipole (Omni-Directional)
Low gain dipoles
radiate everywhere
think ―light bulb‖
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 30
31. Understanding Antenna Patterns
Monopole (Omni-Directional) MIMO
When three monopoles are next to each
other – the radiating elements interact
slightly with each other – The higher gain
4 dBi also changes elevation more
compared to the lower gain 2.2 dBi Dipole
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 31
35. Understanding Antenna Patterns
Sector (Higher Gain Directional)
Elevation plane has nulls due to high gain 14 dBi
AIR-ANT2414S-R
14 dBi Sector 2.4 GHz
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 35
36. Understanding Antenna Patterns
Sector (Higher Gain Directional)
Elevation plane has nulls due to high gain 14 dBi
but antenna was designed with ―Null-Fill‖
meaning we scaled back the overall antenna AIR-ANT2414S-R
gain so as to have less nulls or low signal spots 14 dBi Sector 2.4 GHz
on the ground.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 36
37. The Richfield Ohio (Aironet) Facility
A Quick Peek Where Antennas Are Designed...
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 37
38. The Richfield Ohio (Aironet) Facility Designs
Antennas and Qualifies 3rd Party Antennas
Satimo software compatible with Cisco Anechoic chamber using an 18-inch
Stargate-64 System. Basic
measurement tool is 8753ES
absorber all the way around 1-6 GHz
Network Analyzer. Anechoic means ―without echo‖
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 38
39. FCC Regulatory Compliance Testing Is Also
Done at the Richfield Ohio Facility.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 39
40. Yes We Have Just a Few Access Points…
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 40
41. RF Screen Rooms Everywhere
Copper Shielding (Faraday Cage)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 41
42. RF Screen Rooms
Copper Shielding on Top Metal on Bottom
Cables are typically fiber and exit Doors have copper fingers and
through well shielded holes latch tight forming an RF seal
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 42
43. RF Screen Rooms
Copper Shielding (Faraday Cage)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 43
46. Understanding Multipath
Multipath Can Change Signal Strength
As radio signals
bounce off metal
objects they often
combine at the
receiver
This often results in
either an improvement
―constructive‖ or a
―destructive‖ type of
interference
Note: Bluetooth type radios that ―hop‖ across the entire band can reduce multipath
interference by constantly changing the angles of multipath as the radio wave
increases and decreases in size (as the frequency constantly changes) however
throughput using these methods are very limited but multipath is less of a problem
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 46
47. Understanding Multipath
Multipath Reflections Can Cause Distortion
As the radio waves bounce they can arrive
at slightly different times and angles causing
signal distortion and potential signal
strength fading
Different modulation schemes fair better –
802.11a/g uses a type of modulation based 802.11n with more receivers can
on symbols and is an improvement over the use destructive interference
older modulation types used with 802.11b (multipath) as a benefit but it is best
clients to reduce multipath conditions
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 47
48. Antenna Placement Considerations
AP antennas need placements that are away
from reflective surfaces for best performance
Avoid metal support beams, lighting and
other obstructions.
When possible or practical to do so, always
mount the Access Point (or remote
antennas) as close to the actual users as
you reasonably can
Avoid the temptation to hide the Access
Point in crawl spaces or areas that
compromise the ability to radiate well
Think of the Access Point as you would a
light or sound source, would you really put a
light there or a speaker there?
Never mount antennas near
metal objects as it causes
increased multipath and
directionality
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 48
49. Understanding Diversity (SISO)
802.11a/b/g Diversity Has Just One Radio
Non-802.11n diversity Access Points use two antennas sampling each
antenna choosing the one with the least multi-path distortion
Cisco 802.11a/b/g Access Points start off favoring the right (primary
antenna port) then if multi-path or packet retries occur it will sample the
left port and switch to that antenna port if the signal is better.
Note: Diversity Antennas should always cover the same cell area
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 49
50. Understanding Diversity (MIMO)
MRC Maximal Ratio Combining (Three Radios)
• Receiver benefit as each antenna has a radio section
• MRC is done at Baseband using DSP techniques
• Multiple antennas and multiple RF sections are used in parallel
• The multiple copies of the received signal are corrected and combined at Baseband
for maximum SNR (Signal to Noise) benefit
• This is a significant benefit over traditional 802.11a/b/g diversity where only one
radio is used
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 50
51. Understanding 802.11 MIMO Terminology
MIMO (Multiple-Input-Multiple-Output)
Some RF components of 802.11n include:
MRC – Maximal Ratio Combining a method that combines signals from multiple antennas taking into account
factors such as signal to noise ratio to decode the signal with the best possible Bit Error Rate.
TxBF – Transmit beam forming – The ability to transmit independent and separately encoded data signals, so-
called ―streams‖ from each of the multiple transmit antennas.
Channel Bonding – Use of more than one frequency or channel for more bandwidth.
Spatial Multiplexing – A technique for boosting wireless bandwidth and range by taking advantage of multiplexing
which is the ability within the radio chipset to send out information over two or more transmitters known as ―spatial
streams‖.
Note: Cisco 802.11n Access Points utilize two
transmitters and three receivers per radio module. MIMO is pronounced
―My Moe‖
not
―Me Moe‖
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 51
52. Technical Elements of 802.11n
Packet Backward
MIMO 40Mhz Channels
Aggregation Compatibility
40Mhz Packet Backward
MIMO
Channels Aggregation Compatibility
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 52
53. Aspects of 802.11n
Packet Backward
MIMO 40Mhz Channels
Aggregation Compatibility
MIMO (Multiple Input, Multiple Output)
With Beam Forming
Transmissions Arrive in Phase,
Increasing Signal Strength
Without Beam Forming
Transmissions Arrive out of
Phase and signal is weaker
Performed by Ensures Signal Increases Works with
Transmitter Received in Receive non-MIMO and
(Talk Better) Phase Sensitivity MIMO Clients
Beam Forming Maximal Ratio Combining Spatial Multiplexing
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 53
54. Aspects of 802.11n
Packet Backward
40Mhz Channels
Aggregation Compatibility
MIMO (Multiple Input, Multiple Output)
Without MRC With MRC
Multiple Signals Sent; Multiple Signals Sent and Combined
One Signal Chosen at the Receiver Increasing Fidelity
MIMO AP
Performance
Performed by Combines Increases Works with
Receiver Multiple Received Receive non-MIMO and
(Hear Better) Signals Sensitivity MIMO Clients
Beam Forming Maximal Ratio Combining Spatial Multiplexing
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 54
55. Aspects of 802.11n
Packet Backward
40Mhz Channels
Aggregation Compatibility
MIMO (Multiple Input, Multiple Output)
Information Is Split and Transmitted on Multiple Streams
stream 1
MIMO AP stream 2
Performance
Transmitter and Concurrent Increases Requires MIMO
Receiver Transmission on Bandwidth Client
Participate Same Channel
Beam Forming Maximal Ratio Combining Spatial Multiplexing
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 55
56. Aspects of 802.11n
Packet Backward
MIMO 40Mhz Channels
Aggregation Compatibility
MIMO (Multiple Input, Multiple Output)
40Mhz Channels
Moving from 2 to 4 Lanes
20-MHz
Gained Space 40-MHz
20-MHz
40-MHz = 2 aggregated 20-MHz channels—takes advantage of the
reserved channel space through bonding to gain more than double the
data rate of two 20-MHz channels
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 56
57. Aspects of 802.11n
Packet Backward
MIMO 40Mhz Channels
Aggregation Compatibility
Packet Aggregation
40Mhz Channels
Carpooling Is More Efficient Than Driving Alone
Without Packet Aggregation
Data Data Data
802.11n 802.11n 802.11n
Unit Unit Unit
Overhead Overhead Overhead
Packet Packet Packet
802.11n Data Unit
Overhead
Packet Packet Packet
With Packet Aggregation
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 57
58. Aspects of 802.11n
Packet Backward
MIMO 40Mhz Channels
Aggregation Compatibility
Backward Compatibility
Packet Aggregation
2.4 GHz 5 GHz
11n Operates
in Both
Frequencies
802.11ABG Clients Interoperate with 11n AND
Experience Performance Improvements
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 58
59. Understanding MCS Rates and Channel Bonding
Channel Bonding:
40MHz 802.11n channel Wider channels means more bandwidth per AP
1 2 3 4 5 6 7 8 9 10 11 12 13 14
2.402 GHz 20 MHz channel 2.483 GHz
MCS rates 0-15 apply
Regardless of channel
Bonding.
When you bond a channel
You have a control channel
You have a data (extension)
Channel
Legacy clients use control
Channel for communication
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 59
60. 2.4 GHz, 40 MHz Bandwidths
Tip: Channel bonding in 2.4 GHz should be avoided in enterprise
deployments use 5 GHz as there are no overlapping channels to worry about
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 60
61. Example UNII-3 Channel Bonding
In 40-MHz you define the control channel this is the channel that
is used for communication by Legacy .11a clients.
The Extension channel is the bonded channel that High
Throughput ―HT‖ 802.11n clients use in addition to the control
channel for higher throughput as they send data on BOTH
channels
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 61
62. Channel Bonding – Subcarriers
802.11n uses both 20-
MHz and 40-MHz
channels.
The 40-MHz channels
in 802.11n are two
adjacent 20-MHz
channels, bonded
together.
When using the 40-MHz bonded channel, 802.11n takes advantage of the fact that each 20-MHz channel
has a small amount of the channel that is reserved at the top and bottom, to reduce interference in those
adjacent channels.
When using 40-MHz channels, the top of the lower channel and the bottom of the upper channel don't
have to be reserved to avoid interference. These small parts of the channel can now be used to carry
information. By using the two 20-MHz channels more efficiently in this way, 802.11n achieves slightly more
than doubling the data rate when moving from 20-MHz to 40-MHz channels
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 62
63. Understanding Guard Interval
The guard interval
that is part of each
OFDM symbol is a
period of time that is
used to minimize
inter-symbol
interference.
This type of
interference is
caused in multipath
environments when
the beginning of a
new symbol arrives
at the receiver before
the end of the last Default mode for 802.11n is 800 nanoseconds
symbol is done. If you set a shorter interval it will go back to long
in the event retries occur
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 63
64. MCS Index of 802.11n Rates
NSD NCBPS GI = 800ns GI = 400ns
Number of Rate in Rate in Rate in Rate in
MCS spatial Coding
Index streams Modulation rate 20 40 20MHz 40MHz 20MHz 40MHz 20MHz 40MHz
0 1 BPSK ½ 52 108 52 108 6.5 13.5 7 2/9 15
1 1 QPSK ½ 52 108 104 216 13 27 14 4/9 30
2 1 QPSK ¾ 52 108 104 216 19.5 40.5 21 2/3 45
3 1 16-QAM ½ 52 108 208 432 26 54 28 8/9 60
4 1 16-QAM ¾ 52 108 208 432 39 81 43 1/3 90
5 1 64-QAM 2/3 52 108 312 648 52 108 57 7/9 120
6 1 64-QAM ¾ 52 108 312 648 58.5 121.5 65 135
7 1 64-QAM 5/6 52 108 312 648 65 135 72 2/9 157.5
8 2 BPSK ½ 52 108 104 216 13 27 14 4/9 30
9 2 QPSK ½ 52 108 208 432 26 54 28 8/9 60
10 2 QPSK ¾ 52 108 208 432 39 81 43 1/3 90
11 2 16-QAM ½ 52 108 416 864 52 108 57 7/9 120
12 2 16-QAM ¾ 52 108 416 864 78 162 86 2/3 180
13 2 64-QAM 2/3 52 108 624 1296 104 216 115 5/9 240
14 2 64-QAM ¾ 52 108 624 1296 117 243 130 270
15 2 64-QAM 5/6 52 108 624 1296 130 270 144 4/9 300
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 64
65. So to Recap – 802.11n Operation
Throughput improves when all things come together
802.11a/g AP 54 48 36 24 Mbps
(non-MIMO)
MRC
TxBF 802.11a/g client
(non-MIMO)
Spatial Multiplexing
802.11n AP
54 Mbps
MRC (MIMO)
TxBF 802.11a/g client
Spatial Multiplexing (non-MIMO)
MRC 802.11n AP
300 Mbps Channel Bonding
(MIMO)
TxBF
Spatial Multiplexing 802.11n client
(MIMO)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 65
67. Antenna Technologies ―DAS‖
Traditional DAS Deployments over Coaxial Cable
• DAS – Distributed Antenna System
• Mostly seen in mining, healthcare and manufacturing
• Major benefits of DAS include:
Carry multiple wireless signals simultaneously (cellular, paging, etc)
Minimize work above ceiling
Permits locations such as wiring closets where it is easier to replace
• Disadvantages
Usually one antenna per AP – Implementations vary among vendors
Performance and/or support issues – Sometimes DAS requirement is
not for Wi-Fi but for in-building cellular so WLAN cell sizes suffer
Not a Cisco antenna – DAS antennas are not defined in Cisco’s
Wireless Control System (WCS) must choose a ―close match‖
Reduced technology migration paths - 802.11n can be more difficult to
support
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 67
68. How Does DAS Work?
• DAS works by placing multiple radio services on a common
cable or antenna system using selective filters and/or a low
gain multiband antenna.
• Two methods are typically used ―Leaky coax‖ and ―discrete
wideband antennas‖ or sometimes a combination of both.
• Note: Cisco recommends using only discrete wideband
antennas (one antenna per AP) as this prevents breaking key
features like rogue AP detection and location.
Leaky ―radiating‖ coaxial cable
Bad for location based applications
Wide-Band antenna
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 68
69. Leaky Coax DAS
Cable has shielding removed
on one side – center radiates
Leaky coaxial systems are sometimes used in mining applications and assembly lines
(think above assembly work benches)
To be effective, it needs to be installed in very close proximity to the actual WLAN users
(distances are short typically 5-10 Ft) and will not work at higher 5 GHz
frequencies. Limited to single channel - high potential for co-interference issues
Note: Leaky coax is not recommended for advanced RF features such as voice or
location
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 69
70. Traditional Coaxial DAS Solutions
Depending on the type of ―wide band antenna‖ DAS system, signals
leave the Access Point antenna port and go through mechanical
filters and/or bi-directional amplifier combiner circuitry.
While this is much better then a leaky coaxial system, it is not a
simple installation and requires specialized installers with
experience cutting and terminating the unique low loss cable
that is coaxial in nature but has a hard metal shield. RP-TNC
Terminator
Note: Unused antenna ports should be terminated to avoid adjacent
cell interference
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 70
71. New Approach DAS over CAT-5
Cisco has a Solutions Plus partnership with Mobile Access
Which is offering an active DAS system over unshielded twisted pair
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 71
72. Co-existence of
Wi-Fi and Cellular Antenna
Wi-Fi over
Overlay In-building cellular
Traditional DAS
Shared Coax cabling
No Wi-Fi limitations
APs in closet
No Wi-Fi limitations
Cheap UTP cables
No Cisco RF Support
Likely no MIMO, MRC Expensive cabling
or ClientLink, RRM, Duplicate cabling
Poor roaming, Location
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 72
73. Co-existence with CUWN Wi-Fi
2 Cellular Bands
or 1 MIMO Service
Access
Cellular POE Alt B WLAN AP
Switch Pod
Controller
New / Existing Cat-5/6
Ethernet GigE
POE Alt A
BDA, BTS,
Pico, Femto Cellular WLAN
“Cell, PCS” “802.11n”
Ethernet-LAN MobileAccessVE Frequencies Shared Structured
Traffic Passes Shifts Carrier to Starting at Cabling System is
Over Intermediate 140 MHz and Passive to WLAN
0 to ~100 MHz Frequencies Above and Cellular
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 73
74. Access Points and Features
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 74
75. Introduction of New Access Points
11abg 11n 11n + CleanAir
1250 3500e
Ruggedized
1240
1260
1130 1140 3500i
Carpeted
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 75
76. Aironet Indoor Access Point Comparison
AP 1130 AP 1140 AP 3500i AP 1240 AP 1250 1260 3500e
Integrated CleanAir No No Yes No No No Yes
Data Uplink (Mbps) 10/100 10/100/1000 10/100/1000 10/100 10/100/1000 10/100/1000 10/100/1000
E-PoE
Power Requirement 802.3af 802.3af 802.3af 802.3af
802.3af*
802.3af 802.3af
Installation Carpeted Carpeted Carpeted Rugged Rugged Rugged Rugged
-20 to -20 to -20 to -20 to
Temp Range 0 to +40°C 0 to +40°C 0 to +40°C
+55°C +55°C +55°C +55°C
Antennas Internal Internal Internal External External External External
Wi-Fi standards a/b/g a/b/g/n a/b/g/n a/b/g a/b/g/n a/b/g/n a/b/g/n
DRAM 32 MB 128 MB 128 MB 32 MB 64 MB 128 MB 128 MB
Flash 16 MB 32 MB 32 MB 16 MB 32 MB 32 MB 32 MB
•802.3af fully powers single radio AP1250 or provides 1x3 performance on a dual radio 1250
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 76
77. Integrated Antenna? – External Antenna?
Carpeted areas Rugged areas
Integrated antenna versions Use for industrial applications
are designed for mounting where external or directional
on a ceiling (carpeted areas) antennas are desired and or
where aesthetics is a applications requiring higher
primary concern temperature ranges
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 77
78. When to Use Integrated Antennas
• When there is no requirement for directional
antennas and the unit will ceiling mounted
• Areas such as enterprise carpeted office
environments where aesthetics are
important
• When the temperature range will not exceed
0 to +40C
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 78
79. When to Use external Antennas
Reasons to consider deploying a rugged AP
• When Omni-directional coverage is not
desired or greater range is needed
• The environment requires a more industrial
strength AP with a higher temperature rating
of -20 to +55 C (carpeted is 0 to +40 C)
• The device is going to be placed in a NEMA
enclosure and the antennas need to be
extended
• You have a desire to extend coverage in two
different areas with each radio servicing an
independent area - for example 2.4 GHz in
the parking lot and 5 GHz indoors
• Requirement for outdoor or greater range
Bridging application (aIOS version)
• Requirement for WGB or mobility application
where the device is in the vehicle but
antennas need to be mounted external Rugged AP in ceiling enclosure
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 79
80. When to Use AP-1240 and AP-1250
Reasons to consider the AP-1240 or AP-1250
• The AP-1240 and AP-1250 support higher
gain antennas - a benefit only if a high gain
antenna already exists or is required
• Higher gain (up to 10 dBi) can improve WGB
and Bridging distances
• Recommend the AP-1240 if there is no
requirement for 802.11n support or the
infrastructure is older 10/100 ports
• AP-1240 will work with older Cisco PoE
switches (Cisco proprietary power)
• AP-1240 draws less power so better for
solar applications
• AP-1240 supports Cisco Fiber injectors
• Tip: Higher than 10 dBi antenna gains are
supported with the 1300 Series Bridge/AP
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 80
81. Which 802.11n Access Point Is Right?
• AP-3500i and AP-3500e have the very
latest Cisco features such as Clean Air
Cisco’s spectrum intelligence
• AP-1140 and AP-1260 are of similar
design less Cisco Clean Air features and
can also run autonomous code (aIOS) for
stand alone or Workgroup Bridge
applications. Note: 3500 Series does not
support the older aIOS modes
• All the Access Points were designed to
have similar coverage for ease of
deployment
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 81
82. Coverage Comparison – 5GHz
AP1140 AP1250
AP3500i AP3500e
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 82
84. Content
Site Survey
Access Point Placement
Channel Strategy
Mixed Mode Environments
Network Capacity &
Scalability
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 84
85. Site Survey Prepares for 802.11n
• Recommended to optimize 11n
deployment
• Survey reveals effects of
building characteristics on the
wireless spectrum
Metal Wall
• Measure RF variations due to
human activity and time of day Furniture
• Survey with client types that Elevator
you plan to implement (11n,
11abg, VoIP, location tags)
Glass
• Spectrum intelligence
to detect interference
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 85
86. Access Point Placement
ABG Access Point Placement
1 per 5,000 sq feet for data only
1 per 3,000 sq feet for voice, location ABG
ABG
Radio Resource Management
Adaptive channel / power coverage
Operational simplicity
ABG
ABG
Web
Email
Several Supported
Apps
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 86
87. Access Point Placement
.11n same 1 for 1 replacement
Newer APs reuses existing
Cisco AP bracket drill holes ABG
Improved coverage at ABG
higher data rates
ERP
Backup
Video ABG
Voice
ABG
Web
Email
Supported Apps
802.11n is the same overlay
however more applications
supported at any given location
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 87
88. Effective Frequency Use 5GHz - 2.4GHz
Create a 5 GHz Strategy
• 5 GHz Recommended for 802.11n
More available spectrum—greater number of channels
Benefits from 40MHz channels, although 20MHz still works well
Many 11n devices only support 40MHz in 5GHz, although Cisco supports 40MHz in
both 2.4GHz and 5GHz
• 2.4 GHz still benefits from MIMO and packet aggregation
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 88
89. 5 GHz Dynamic Frequency Selection
When Radar Is
Present
APs Shift
Channels—
Results in Lower
Available Channels
and Loss of UNI 2
and UNI 2e Bands Radar
No DFS DFS
Available Support Support
40MHz
Channels 4 11
5 GHz Frequency
UNI 1 UNI 2 UNI 2 Ext. UNI 3
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 89
90. DFS and Available Bandwidth
• Full DFS support is required for Available Bandwidth in 5GHz for 11n
complete use of channels in 5GHz 1350
1350Mbps 1350Mbps
1200
• Limited DFS support directly 1050
impacts available bandwidth 900
750 US Europe
600Mbps
• Limited bandwidth restricts
600
450
application support and 300 US
300Mbps
Europe
negates investment in 11n 150
0
Meru/Aruba Meru/Aruba Cisco Cisco
* 40 MHz Channels in 5GHz
Available Channels per Region Theoretical Cisco Meru/Aruba
11n 5GHz
24 21 8
20MHz
United States
11n 5GHz
11 9 4
40MHz
11n 5GHz
19 19 4
20MHz
Europe
11n 5GHz
9 9 2
40MHz
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 90
91. Backward Compatibility & Co-Existence
• Co-existence of ABG/N APs
• Benefits of 11n accrue to ABG clients
MIMO benefits ABG clients on the AP receive side from MRC
Co-Existence at Controller Level Backwards Compatibility
WLAN Controller WLAN Controller
11g 11n 11g 11n
54 Mb
48 Mb
36 Mb
28 Mb 300 Mb 54 Mb 300 Mb
Roam
11g 11n 11g 11n
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 91
92. Mixed Mode Performance
3 Modes of operation
WLAN Controller
supported
Capacity Legacy
300mb Green Field
11n Mixed
Mixed mode experiences
slight performance impact
0
due to ABG clients
54 Mb 300 Mb 11n clients still transmit at
full performance
PHY and MAC for 11n
11g 11n provides co-existence and
protection for ABG clients
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 92
93. Wall Mounting Which Model to Choose?
AP-1140 and AP-3500i AP-1260 and AP-3500e
Wall mounting is acceptable Best for enterprise deployments as
for small deployments such coverage is more uniform
as hotspots, kiosks, etc but especially for advanced features
radiation is better on ceiling such as voice and location
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 93
94. Aironet 1140 / 3500i (style case)
Third party wall mount option is available
Oberon model 1029-00 is a right angle mount
http://www.oberonwireless.com/WebDocs/Model1029-00_Spec_Sheet.pdf
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 94
95. Access Points (Internal Antenna Models)
Designed Primarily for Ceiling (Carpeted) Installations
Access Point has six
integrated 802.11n
MIMO antennas
4 dBi @ 2.4 GHz
3 dBi @ 5 GHz
Note: Metal chassis and antennas were designed to benefit ceiling installations
as the signal propagates downward in a 360 degree pattern for best performance
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 95
96. Antenna Patterns
Azimuth and Elevation Patterns for 2.4 GHz & 5 GHz
2.4 GHz
5 GHz
Azimuth
Azimuth
2.4 GHz 5 GHz
Elevation Elevation
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 96
97. What About Mounting Options?
Different Mounting Options for Ceiling APs
Locking enclosures and different
color plastic ―skins‖ available from
third party sources such as
Cisco has options to mount to www.oberonwireless.com
most ceiling rails and directly into www.terrawave.com
the tile for a more elegant look
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 97
98. Clips Adapt Rail to ―T‖ Bracket.
Attaching to Fine Line Ceiling Rails
If the ceiling
rail is not
wide enough
or too
recessed for
the ―T‖ rail
this can be
addressed
using the
optional clips
Part Number for ceiling clips is AIR-ACC-CLIP-20=
This item is packaged in 20 pieces for 10 Access Points
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 98
99. AP Placement in Plenum Areas
• When placing the Access Point above the
ceiling tiles (Plenum area) Cisco
recommends using rugged Access Points
with antennas mounted below the Plenum
area whenever possible
• Cisco antenna have cables that are plenum
rated so the antenna can be placed below
the Plenum with cable extending into the
plenum
• If there is a hard requirement to mount
carpeted or rugged Access Points using
dipoles above the ceiling – This can be done
however uniform RF coverage becomes
more challenging especially if there are
metal obstructions in the ceiling
• Tip: Try to use rugged Access Points and
locate the antennas below the ceiling
whenever possible
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 99
100. Installation Above the Ceiling Tiles
An Optional Rail Above the Tiles May Be Used
Note: The AP should be as close to the tile as practical
AP bracket supports this optional T-bar box hanger item 2
(not supplied) Such as the Erico Caddy 512 or B-Line BA12
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 100
101. Installation Above the Ceiling Tiles
Mount AP Close to the Tiles and Away from Objects
Installing Access Points
above the ceiling tiles should
be done only when mounting
below the ceiling is not an
option.
Such mounting methods can
be problematic for advanced
RF features such as voice
and location as they depend
on uniform coverage
Tip: Mount antennas either
below ceiling tile or the AP
as close to the inside of the
Try to find open ceiling areas away from
tile as possible
metal obstructions (use common sense)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 101
102. Plenum Installs That Went Wrong
Yes It Happens and When It Does Its Bad…
When a dipole is mounted
against a metal object you
lose all Omni-directional
properties.
It is now essentially a
directional patch suffering
from acute multipath
distortion problems.
Add to that the metal pipes
and it is a wonder it works at
all.
Tip: Access Points like light
Dipole antennas up against a metal box and sources should be near the
large metal pipes Multipath everywhere users – Perhaps the AP is here
for ―Pipe Fitter Connectivity‖?
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 102
103. Plenum Installs That Went Wrong
Huh?? You Mean It Gets Worse?
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 103
104. Installations That Went Wrong
Ceiling mount AP up against pipe hmmm A little ICE to keep the packets cool
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 104
105. Installations That Went Wrong
Patch antenna shooting across a metal fence Mount the box and antennas
downward Please
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 105
106. Installations That Went Wrong
Sure is a comfy nest glad the AP runs a bit on the warm side
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 106
107. Minimize the Impact of Multipath
• Temptation is to mount on beams or
ceiling rails
• This reflects transmitted as well as
received packets
• Dramatic reduction in SNR due to
high-strength, multipath signals
Minimize Reflections When Choosing Locations
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 107
108. Antennas for Rugged
Access Points
802.11n Options for Ceilings and Walls
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 108
109. Guide to Antenna Part Numbers
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 109
110. MIMO Ceiling Antenna 2.4 GHz
AIR-ANT2430V-R (3 dBi Ceiling Mount Omni)
Antenna has three
monopole elements
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 110
111. MIMO Ceiling Antenna 5 GHz
AIR-ANT5140V-R (4 dBi Ceiling Mount Omni)
Antenna has three
monopole elements
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 111
112. AIR-ANT2451NV-R
2.4 GHz (2.5 dBi) & 5 GHz (3.5 dBi) Dual Band Ceiling Omni
Six leads - 5 GHz antennas have blue
markings (shrink wrap)
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 112
113. AIR-ANT2460NP-R
2.4 GHz 6 dBi Three Element Patch
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 113
114. AIR-ANT5160NP-R
5 GHz 6 dBi Three Element Patch
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 114
115. AIR-ANT2450NV-R= & AIR-ANT5140NR-R
MIMO ―Multi-mount‖ Omni 2.4 GHz and 5 GHz
New 3 in 1 Antenna for 2.4 GHz and 5
GHz.
Gain is 4 dBi
Comes with articulating wall mount, can
also be used on ceiling
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 115
116. New Cisco Antenna Part Numbers
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 116
117. Outdoor Weatherproofing
Coax-Seal can be used with
or without electrical tape.
Taping first with a quality
electrical tape like Scotch 33+
vinyl allows the connection to
be taken apart easier.
Many people tape then use
Coax-Seal then tape again
this allows easy removal with
a razor blade.
Note: Always tape from the
bottom up so water runs over
the folds in the tape. Avoid
using RTV or other caustic
www.coaxseal.com material.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 117
118. Complete Your Online
Session Evaluation
Receive 25 Cisco Preferred Access points for each session
evaluation you complete.
Give us your feedback and you could win fabulous prizes.
Points are calculated on a daily basis. Winners will be notified
by email after July 22nd.
Complete your session evaluation online now (open a browser
through our wireless network to access our portal) or visit one
of the Internet stations throughout the Convention Center.
Don’t forget to activate your Cisco Live and Networkers Virtual
account for access to all session materials, communities, and
on-demand and live activities throughout the year. Activate
your account at any internet station or visit
www.ciscolivevirtual.com.
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 118
119. Visit the Cisco Store for
Related Titles
http://theciscostores.com
BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 119
120. BRKEWN-3016 © 2011 Cisco and/or its affiliates. All rights reserved. Cisco Public 120