6. Dedicated Push Pull Components Pantograph cylinder and gripper jaw. Rear frame with side shift. Push Plate with pads to clamp the slip sheet. Cylinder for the hydraulic positioning of the platens .
7. Rear Frame Rear view Side shifting cylinder. On request, non-side shifting version. Adjustable lower hooks. On request, lower quick hooks, and bronze pads. Dedicated Push Pull
8. Platens Manufactured in high tensile steel Smoothed and rounded corners and surfaces in order to avoid damage to the slip-sheet and to the load Manual positioning: standard Platens positioning cylinder: on request. Dedicated Push Pull
9. Two pantograph cylinders in order to better distribute the forces between the articulated joints. Dedicated Push Pull Pantographs: All joints, bushings and rollers are grease-able. Pantograph fixing points with spherical joints.
10. Pushing Plate Wide windows for the maximum driver’s visibility. The push plate has a 4-degree tilting, with fully extended pantograph, to get a better vertical alignment with the load. The gripper jaw is operated by a sequence valve, that automatically intervenes, when the pantograph is fully extended. Dedicated Push Pull
11. ( With side-shifting and hydraulic placing of platens ) Lift truck with 4 functions: I° lifting II° mast tilting III° side shifting IV° pantograph and placing platens (to place the platens hydraulically it is necessary to have 24 volt DC) Valve check pressure Sequence valve pantograph/gripper jaw Port for hydraulic system Sideshifting cylinder with fixed speed regulation in the fittings Cylinder placing the platens Pantograph cylinder Cylinder to clamp the sheet Regulate speed Dedicated Push Pull Hydraulic System
13. Fork-mounted Push Pull Easy Rider Bolzoni Auramo Push Pulls – Presentation B3054US - 03-2010 - Bolzoni Auramo Mktg Dept – Piacenza - Italy GO TO RANGE PAGE
14. Fork-mounted Push Pull Components Pantograph cylinder and gripper jaw. Rear frame Push Plate with pads to clamp the slip sheet. Platens
15. Rear Frame Fork-mounted Push Pull Fork pockets under the plates outside the frame width Release pins and raise lower hooks to secure the unit to the truck fork carriage
16. Hooking device Fork-mounted Push Pull 1 – Position the forks with internal distance 22.6”-23.2” 2 – Tilt the mast forward 3 - Fork the attachment with the forks external to the frame. 4 – Lift the carriage up and hook the upper hooks. 5 – Lift the lower hooks up and block them in hooking position. 6 – Connect the hydraulic couplings.
17. Platens Manufactured in high tensile steel. Smoothed and rounded corners and surfaces in order to avoid damage to the slip-sheet and to the load. Fork-mounted Push Pull
18. Pantographs: All joints, bushings and rollers are grease-able. Pantograph fixing points with spherical joints. Hoses to feed the clamping cylinder. Back and front rollers with bushing and axial pads. Sequence valve Pushing plate fixing. Fork-mounted Push Pull 2 pantograph cylinders in order to better distribute the forces between the articulated joints.
19. Pushing Plate Fork-mounted Push Pull Wide windows for the maximum drivers visibility. The push plate has a 4-degree tilting, with fully extended pantograph, to get a better vertical alignment with the load. The gripper jaw is operated by a sequence valve, that automatically intervenes, when the pantograph is fully extended.
21. Product Highlights Fork-mounted Push Pull Hydraulic clamping system Sequence valve with no need for further hydraulic function New hooking system: ease of use and total stability of the pantograph Adjustable push plate cylinder height: no maintenance cost
22. Mark 55 Push Pull Bolzoni Auramo Push Pulls – Presentation B3054US - 03-2010 - Bolzoni Auramo Mktg Dept – Piacenza - Italy GO TO RANGE PAGE
23. Mark 55 Push Pull Components Pantograph cylinder and gripper jaw. Rear frame with side shift. Push Plate with pads to clamp the slip sheet. Platens with cylinder for the hydraulic positioning of outer platens
24. Rear Frame Rear view Selector for extension or platens positioning (not available in the platens manual positioning version) Side shifting cylinder (Non-side shifting version without cylinder) Adjustable lower hooks. On request, quick disconnect lower hooks and bronze pads Mark 55 Push Pull
25. Platens Guide pin in chromed steel protected with scraper for guide cleaning Mark 55 Push Pull Manufactured in high tensile steel. Smoothed and rounded corners and surfaces in order to avoid damage to the slip-sheet and to the load. Platen support with grease-able bushings Adjustments of platen tip alignment
26. Mark 55 Push Pull Pantographs Hoses to feed the clamping cylinder Sequence valve Push plate fixture Rear and front rollers with bushings and lateral pads Hoses protection with plastic wire wrapper All joints, bushings and rollers are greasable. Pantograph fixing points with spherical joints. 2 pantograph cylinders in order to better distribute the forces between the articulated joints.
27. Pushing Plate Mark 55 Push Pull Wide windows for maximum visibility. To get a better vertical alignment with the load the push plate has a 4 degree tilt when the pantograph is fully extended. The gripper jaw is activated by a sequence valve that operates automatically when the pantograph is fully extended .
28.
29. Options Mark 55 Push Pull Quick disconnect hydraulic couplers Various platen widths and lengths Extended push plate widths and heights Bronze pads for sideshift
30. Mark 55 Push Pull Product Features Wide windows in the push plate and gripper jaw allows for excellent visibility in both retracted and extended positions when clamping the slip-sheet. The hydraulically adjustable outer platens slide on chromed bars allowing for both slip sheet and pallet handling. Adjustable platen inclination for tip alignment, to avoid load damage. The vertical position of the gripper pad is adjustable should the pad becomes worn or damaged, resulting in less maintenance costs. 4 degrees tilting faceplate, when fully extended, helps prevent any damage to the product. Gripper jaw is actuated by two cylinders, assuring a perfect force distribution on the clamping bar to help eliminated any damage to the slipsheet. Pressure relief valve guarantees structure and load protection.