O slideshow foi denunciado.
Utilizamos seu perfil e dados de atividades no LinkedIn para personalizar e exibir anúncios mais relevantes. Altere suas preferências de anúncios quando desejar.

Timer & Interrupt Atmega16

Slide to demonstrate how to configure Atmega16 to work in interrupt and Timer

  • Seja o primeiro a comentar

Timer & Interrupt Atmega16

  1. 1. By/Ramadan Ahmed
  2. 2. What’s Interrupts ?
  3. 3. Basically events that require immediate attention by the microcontroller. An interrupt is a signal to the processor emitted by hardware or software indicating an event that needs immediate attention. When an interrupt event occurs, the microcontroller pause its current task and attend to the interrupt by executing its corresponding Interrupt Service Routine (ISR) then microcontroller returns to the task it had pause and continue its normal operations.
  4. 4. Such an event may be:  An peripheral device has finished the last task it was given and is now ready for another. For example Timer may generate interrupt after reaching the maximum possible value.  External Interrupt event on I/O Pin.  An error from a peripheral. You can think of it as a hardware-generated function call.
  5. 5. ISR (Interrupt service routine)  Piece of code that should be execute when an interrupt is triggered  Should be deterministic and short as possible, as it usually set a flag to a specific task indicating a certain event is happened, or save small data in buffer.
  6. 6. REMEMBER Global interrupt enabled bit MUST be enabled for interrupts to be activated in the µC. To Set global interrupt :  sei(); To clear global interrupt :  cli();
  7. 7. Interrupt Flags and Enabled bits in AVR µC  Each interrupt is associated with two (2) bits, an Interrupt Flag Bit and an Interrupt Enabled Bit. These bits are located in the I/O registers associated with the specific interrupt: The interrupt enabled bit(IE): is used to enable or disable a specific interrupt. Basically is tells the µC whether or not it should respond to the interrupt if it is triggered. The interrupt flag bit (IF):is set whenever the interrupt event occur, whether or not the interrupt is enabled. And The flag is cleared when the ISR is executed. So it is also called “Automatic Flag”.
  8. 8. Global interrupt Interrupt flag Interrupt enabled Interrupt Request
  9. 9. RESET interrupt  It active low interrupt which means it triggered when low voltage (0 volt) is applied on reset pin (number 9).
  10. 10. Timer is special register that can be 8- 16 bit so capable of holding from 0 to 255-65536 What differ it from any register that it count up / down automatically at predefined rate and this is Timer Clock that doesn’t need CPU intervention. Timer Clock could be internal / external
  11. 11. One of basic condition when Timer overflow( it means timer counted up to its maximum value and return back to zero). In this situation it causes interrupt and if global interrupt mask is enabled and timer interrupt enable so you have to write ISR to handle the event of the overflow
  12. 12. Resolution:  is the smallest period taken by timer to take one count we can calculate it through formula Resolution = (1/Frequency)  If you using 1 MHZ for CPU Clock timer takes to count up till it overflow 256 us  So if microcontroller is clocked with 1MHz source, then 8 bit timer will run with resolution: Resolution=1/1MHz=1µs
  13. 13. In case you want to increase the time needed for specific operation we use timer prescalar Prescalar divide the clock frequency and produce timer clock Prescalar modes are  No prescalar (Timer Clock).  Clock/8.  Clock/64.  Clock/256.  Clock/512.  Clock/1024.  NO clock. Note CPU Clock doesn’t affected by reduction using prescalar. It remain the same
  14. 14. Example for using prescalar :  If you using 1 MHZ for CPU Clock without using prescalar timer takes to count up till it overflow 256 µs  But when you use prescalar 1024 timer takes to count up till it overflow 0.26 sec  It’s easy to know the time timer need to overflow if you know Resolution. Resolution = (1/Frequency)  So if microcontroller is clocked with 1MHz source, then 8 bit timer without prescaler will run with resolution: Resolution=1/1MHz=1µs
  15. 15. So if timer take 256 counts to overflow then it takes : T= Resolution * 256 = 1µs *256 = 256 µs  And when we use 1024 as prescalar: Resolution = 1024 / 1 MHZ = 1024µs T = Resolution * 256 = 1024 * 256 = 0.256s
  16. 16. ATmega16/32 have 3 Timer/counter we have three Timers/Counters each one with Separate Prescaler.  Timer 0 - 8 bit timer.  Timer 1 -16 bit timer.  Timer 2 - 8 bit timer. Timer also can be operated in 3 modes :  Normal mode (Overflow).  Pulse Width Modulation mode(PWM).  Clear Timer Compare mode(CTC ).
  17. 17. Timer0  Timer1 is an 16 bit timer/counter which can count from 0 to 0xFF (256).  In the timer mode this peripheral uses an internal clock signal.  In the counter mode an external signal on PIN0 in PORTB.  The timer can be operated either in the polling mode or in the interrupt mode.
  18. 18.  Timer/Counter Control Register – TCCR0  Bit 7 – FOC0: Force Output Compare  The FOC0 bit is only active when the WGM00 bit specifies a non- PWM mode.  Bit 3, 6 – WGM01:0: Waveform Generation Mode
  19. 19.  Bit 5:4 – COM01:00 Compare Match Output Mode
  20. 20. Bit 2:0 – CS02:0: Clock Select
  21. 21. Timer/Counter Register – TCNT0  This is where the 8-bit counter of the timer resides. The value of the counter is stored here and it increases automatically each clock cycle. Data can be both read/written from this register. The initial value of the counter is set by writing it.
  22. 22. Output Compare Register – OCR0  The Output Compare Register contains an 8-bit value that is continuously compared with the counter value (TCNT0). A match can be used to generate an output compare interrupt, or to generate a waveform output on the OC0 pin.
  23. 23. Timer/Counter Interrupt Mask Register –TIMSK  TOIE0: Timer Overflow Interrupt Enable  OCIE0: Output Compare Match Interrupt Enable
  24. 24.  Timer/Counter Interrupt Flag Register – TIFR  TOV0:  The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared by hardware when executing the corresponding interrupt handling vector. When the SREG I-bit, TOIE0 (Timer/Counter0 Overflow Interrupt Enable), and TOV0 are set (one), the Timer/Counter0 Overflow interrupt is executed.  OCF0  The OCF0 bit is set (one) when a compare match occurs between the Timer/Counter0 and the data in OCR0 – Output Compare Register0. OCF0 is cleared by hardware when executing the corresponding interrupt handling vector. When the I-bit in SREG, OCIE0 (Timer/Counter0 Compare Match Interrupt Enable), and OCF0 are set (one), the Timer/Counter0 Compare Match Interrupt is executed.
  25. 25. Normal Mode (Overflow)  A timer overflow means that the counter(TCTNx) has counted up to its maximum value and is reset to zero in the next timer clock cycle.  The resolution of the timer determines the maximum value of that timer.  The timer overflow event causes the Timer Overflow Flag (TOVx) to be set in the Timer Interrupt Flag Register (TIFR).
  26. 26. Pulse Width Modulation  is the technique used to generate analogue signals from a digital device like a MCU. Almost all modern MCUs have dedicated hardware for PWM signal generation.  A digital device, like a microcontroller can only generate two levels on its output lines, HIGH=5v and LOW=0V.  But what if we want to generate 2.5v or 3.1v or any voltage between 0-5 volt output ?  For these kinds of requirement, instead of generating a constant DC voltage output we generate a square wave, which has high = 5V and Low = 0v  We will use the simplest timer, TIMER0 for PWM generation.
  27. 27.  Pulse Width Modulation  The period (frequency) depends upon the prescaler settings. Now for PWM generation from this count sequence we have a OCR0 (Output Compare Register Zero Register). We can store any value between 0-255 in OCR0, say we store 64 in OCR0 then it would appear in the graph as follows (the RED line).  When the TIMER0 is configured for fast PWM mode, while up counting whenever the value of TIMER0 counter (TCNT0 register) matches OCR0 register an output PIN (OC0 PIN) is pulled low (0) and when counting sequence begin again from 0 it is SET again (pulled high=VCC).
  28. 28.  Pulse Width Modulation Note: to be able to generate an output from the PWM in Timer0, the Output Compare Pin of Timer0 (OC0) must be set as output pin. DDRB |= PB3