Birkosit tds msds 2012

A.I. Schulze
Chemotechnische Fabrik e.K.
Alleinhersteller und Vertrieb
BIRKOSIT Dichtungskitt
®
A.I. Schulze Chemotechnische Fabrik e.K., Johannes-Robert-Becher-Straße 39, 02827 GÖRLITZ - GERMANY
A.I. Schulze Chemotechnische Fabrik e.K. Volksbank Niederschlesien eG Tel. +49 3581 75005-0
Inh. Dieter Bartkowiak Bank sort code 855 910 00 Fax +49 3581 75005-20
Company address: Account number 4 562 135 800 email: info@a-i-schulze.com
Johannes-Robert-Becher-Straße 39 IBAN DE33 8559 1000 4562 1358 00 Web: www.a-i-schulze.com
02827 GÖRLITZ BIC GENODEF1GR1 Register court: Amtsgericht Dresden
GERMANY VAT ref. no. DE812553785 HRA 7441
®
for maximum temperature and pressure resistance
Product number AIS B010
BIRKOSIT BIRKOSIT Dichtungskitt
®
is a single-component, paste luting agent/sealing material for
Description industrial use wherever conditions of temperature combined with pressure on smooth,
plane sealing surfaces (butt joints) make extreme demands on the quality of the
sealing compound. This applies, in particular, to the sealing of metallic joints in:
steam and gas turbines, compressors, generators, expanders, pumps, flange
joints, etc.
®
withstands hot steam and air, hot and cold water, light fuel
Temperature oils and lubricants, as well as crude oil and natural gas at temperatures of
resistance up to 900 °C.
BIRKOSIT The adhesion on sealing surfaces and butt joints is so high that a one hundred
Pressure percent seal is guaranteed even for pressures up to 250 bar.
resistance The pressure resistance for flanges without sealing rings is guaranteed up to 450 bar,
and even up to 550 bar for screw joints.
BIRKOSIT When used in accordance with instructions and with regular servicing as required for
Service life steam and gas turbines as well as for the application areas stated above, we
guarantee a service life for use on machined sealing surfaces (butt joints) of 10 years.
®
is suitable for sealing all surface sizes. The surface quality of
Fields of the sealing surfaces complies with milled/scraped surfaces with a finishing accuracy
Application of Ra = 0.8 µm to 1.2 µm.
Sealing surface damage of ≤ 0.2 mm is compensated with BIRKOSIT Dichtungskitt
®
.
For spot repairs on badly damaged areas of ≥ 0.2 mm to 1.0 mm, we recommend
the products FILLING basic
®
, FILLING 1000
®
and FILLING 2000
®
.
BIRKOSIT Apply the BIRKOSIT Dichtungskitt
®
to the dry sealing surfaces with a brush or putty knife.
Application The layer thickness to be applied is 0.2 mm to 0.3 mm. The product can be
subjected to workloads immediately! It does not cure, will not change its
consistency even after several hours, and remains flexible and elastic.
It is therefore also suitable for butt joint machining. The colour is reddish brown.
Heating the tin to room temperature or adding a tenth part of standard
linseed oil varnish (AIS B020) from our product range will improve the brushability.
BIRKOSIT Packed in 1 kg tins. If stored correctly, BIRKOSIT Dichtungskitt
®
has a storage life
Storage of 5 years in the tin. Its properties are stable and it is flexible in use.
Close the tin properly if only a part of the contents is going to be used.
Product data sheet as at 01.05.2012. Current download version at www.a-i-schulze.com.

A.I. Schulze
®
®
In addition to the product information in our product documents, the 2012 product specification sheet and
the safety data sheet as per (EU) Nr. 453/2010, we confirm the following additions for our General Agency:
Quality management
To ensure the high quality of our products and services and to continually improve our organisation, we
regularly perform in-house audits to make sure that our company meets the requirements of the DIN EN
ISO 9001 quality standard to which our company is certified.
Service life of the product BIRKOSIT Dichtungskitt
®
BIRKOSIT When used in accordance with instructions and with regular servicing as
Service required for steam and gas turbines, we guarantee a service life of 10 years
life for use on machined sealing surfaces (butt joints) with a finishing accuracy of
Ra = 0.8 µm to 1.2 µm as well as incidences of shallow, trough-like corrosion or
erosion defects at these sealing surfaces of ≤ 0.2 mm. For high-pressure turbines (H),
medium-pressure turbines (M) and low-pressure turbines (L) we guarantee that the
product will withstand hot steam and hot air, hot and cold water, light fuel oils and
lubricants as well as crude oil and natural gas up to 900 °C and withstand pressure up
to 250 bar.
BIRKOSIT The following information on the tin label of our products ensures reliable
Service life data service life monitoring:
on the tin Filling date, unopened useable until, service life after opening, opened on
(the last detail is to be entered by qualified staff working for the customer)
BIRKOSIT Unopened tin
Service life data If stored correctly, we guarantee a service life of the product in the tin of 5 years.
in storage Opened tins
If the tins are resealed correctly after partial use, we guarantee a service life of the
product of 3 years.
BIRKOSIT After removal from the tin, we guarantee a product service life of 10 years for the
Product use product in use.
1 Storage life certificate as at 01.09.2012. Current download version at www.a-i-schulze.com.
Görlitz, 01.09.2012
A.I. Schulze Chemotechnische Fabrik e.K.
Company Management
Dieter Bartkowiak

A.I. Schulze
®
®
Safety data sheet conforming to Regulation (EU) No 453/2010
®
Date: 01.09.2012 Page 1 of 10 replaces all previous safety data sheets
The latest version may be found on our website: www.a-i-schulze.com
The information provided here is based on our knowledge and experience at the current time. The safety
data sheet sets out the safety requirements relating to our product and does not constitute a warranty of
any particular properties. It is the responsibility of the consignee of our product to observe the existing
laws and regulations.
SECTION 1: Identification of the substance / mixture and of the company / undertaking
1.1. Product identifier:
Registered trade name: BIRKOSIT Dichtungskitt
®
1.2. Relevant identified uses of the substance or mixture and uses advised against
Usage: Sealing of metallic joints
1.3. Details of the supplier of the safety data sheet
Company: A.I. Schulze Chemotechnische Fabrik e.K.
Address: Johannes-Robert-Becher-Straße 39, 02827 GÖRLITZ, GERMANY
Contact: Tel. +49 3581 75005-0 Fax +49 3581 75005-20
email: management@a-i-schulze.com
1.4. Emergency telephone number
Emergency information service: Tel. +49 3581 75005-10 (24h)

A.I. Schulze
®
®
®
Page 2 of 10
SECTION 2: Hazards identification
2.1. Classification of the substance or mixture
Not applicable as it does not meet the criteria for classification under Directive 199/45/EC.
2.2. Label elements
The use of the product poses no particular risk as long as it is used in compliance with the standard
regulations for industrial hygiene, health and safety.
No labelling of the product is required under EC Directives.
2.3. Other hazards
The product presents no significant hazard for the environment if it is disposed of in compliance with the
standard regulations for waste disposal (cf. section 13).
SECTION 3: Composition / information on ingredients
3.2. Mixtures
Formulation based on a modified organic resin and a paraffin-base mineral oil. The formulation contains
both inorganic and organic additives.
The product contains the following relevant components:
CAS no. Name REACH EEC no. Index no. Symbols R phrases
8001-26-1 Linseed oil varnish - - - - -
1309-37-1 Synthetic iron oxide 01-2119457614-35-0000 - - - - 3 mg/m3

A.I. Schulze
®
®
®
Page 3 of 10
SECTION 4: First aid measures
4.1. Description of first aid measures
General information: Inhalation is not a primary route of exposure. The advice given there is of a general
nature.
In case of contact with eyes: Hold eyelid wide open and rinse the eye out thoroughly with water. Consult
an eye specialist if irritation persists.
In case of skin contact: Remove the product as far as possible with a clean soft cloth then wash the
affected areas of the skin thoroughly with soap and water.
In case of ingestion: Arrange medical treatment for the affected person if necessary.
In case of inhalation: Help the affected person out into the fresh air. Consult a doctor if nausea persists.
4.2. Most important symptoms and effects, both acute and delayed
No known symptoms and effects to date.
4.3. Indication of any immediate medical attention and special treatment required
No known special measures to be taken other than the treatment of symptoms.
SECTION 5: Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media: CO2, powder and foam extinguishers, water spray jet.
Unsuitable extinguishing media: Full water jet.

A.I. Schulze
®
®
®
Page 4 of 10
5.2. Special hazards arising from the substance or mixture
The product is only sold in small containers therefore no particular hazards are to be anticipated as a
general rule. The product is combustible. Gases and vapours which are harmful to health and have an
irritant effect are released during the incineration or thermal decomposition of the product.
5.3. Advice for firefighters
This advice relates to large fires only. Keep containers cool with water spray if they have been exposed to
the fire. Use self-contained breathing apparatus and put on protective clothing in the event of a fire.
Collect and dispose of firefighting water as far as possible.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Pick up small undamaged containers (tins, tubes, etc.). Take measures to stop the flow from any
damaged containers and put on protective equipment before cleaning up any large spillages.
6.2. Environmental precautions
Take measures to prevent leakage into the drainage and water systems.
6.3. Methods and material for containment and cleaning up
Clean up any spillages with a dry absorbent agent (sand, earth, universal binder, etc.) and dispose of
residues as instructed in section 13. Clean the floor thoroughly.
6.4. Reference to other sections
See section 13.

A.I. Schulze
®
®
®
Page 5 of 10
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Ensure adequate indoor ventilation at all times when using the product. Do not smoke while using the
product. Precisely follow the instructions for use.
7.2. Conditions for safe storage, including any incompatibilities
These measures relate to the storage of large quantities of the product. Store the product in the sealed
original containers in a cool and dry place. Take appropriate measures to prevent the product from
entering the drainage or water circulation systems in case of spillage. Do not store the product in the
vicinity of food, beverages or feedstuff, and keep out of reach of children. Heed the storage class when
storing large quantities or when storing in bulk. Storage class 11 under the classification system
developed by the VCI, the German chemical industries association (1991).
7.3. Specific end uses
No further recommendations.
SECTION 8: Exposure controls / personal protection
8.1. Control parameters
No further measures required over and above those set out in section 7.
8.2. Exposure controls
Individual protection measures, such as personal protective equipment:
Do not eat, drink or smoke in the workplace. Avoid repeated / sustained contact with the product. Change
soiled workwear and clean thoroughly before reuse. Do not rub your eyes with dirty hands. Wash your
hands after working and before going to the toilet.
Respiratory protection: Not required

A.I. Schulze
®
®
®
Page 6 of 10
Eye protection: Safety glasses with side shields (not mandatory but recommended)
Hand protection: Plastic gloves (not mandatory but recommended)
Personal protection: Workwear
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Form: Viscous at 20 °C
Colour: Coloured
Odour: Characteristic
9.2. Other information
Density: (25 °C) ~ 1.1 g/cm
3
Bulk density: (20 °C) not applicable
Vapour pressure: (20 °C) < 1 hPa
Viscosity: (25 °C) no data
Solubility in water: (20 °C) virtually insoluble
Solubility in fat: Partly miscible with common organic solvents
pH: Not applicable
Flash point: Non-flammable
Ignition temperature: Non-combustible

A.I. Schulze
®
®
®
Page 7 of 10
Explosion hazards: None
Partition coefficient n-octanol/water, log POW: Not applicable
SECTION 10: Stability and reactivity
10.1. Reactivity
Not relevant.
10.2. Chemical stability
Stable.
10.3. Possibility of hazardous reactions
No known reactions.
10.4. Conditions to avoid
The product is stable at room temperature.
10.5. Incompatible materials
Strong oxidants.
10.6. Hazardous decomposition products
Carbon monoxide, carbon dioxide and inorganic oxides are formed during the combustion / thermal
decomposition of the product.

A.I. Schulze
®
®
®
Page 8 of 10
SECTION 11: Toxicological information
11.1. Information on toxicological effects
The use of the product poses no significant risk as long as it is used in compliance with the standard
regulations for industrial hygiene, health and safety.
LD/LC50 data relevant to classification:
Oral LD50 4986 mg/kg (rat)
SECTION 12: Ecological information
12.1. Toxicity
Do not allow product to leach into the environment. Decant and treat contaminated waste water before it
is discharged into the drainage system.
12.2. Persistence and degradability
Not relevant.
12.3. Bioaccumulative potential
Not relevant.
12.4. Mobility in soil
Not relevant.
12.5. Results of PBT and vPvB assessment
Not relevant.

A.I. Schulze
®
®
®
Page 9 of 10
12.6. Other adverse effects
Water hazard class WK 1 (slightly hazardous to waters) (according to VwVwS publication dated
17.05.1999, formerly WK 0 which has now ceased to exist).
SECTION 13: Disposal considerations
13.1. Waste treatment methods
Make sure the containers (tins, tubes, etc.) are completely empty and recycle them in the normal way.
End users can dispose of small quantities of residues in the original packaging at their local hazardous
waste disposal facility (mobile hazardous waste collection service). Professional users must dispose of
the product in accordance with the waste code number.
Waste code number: 559 07 Lute and mastic compounds, not fully hardened
SECTION 14: Transport information
There are no specific precautions to be taken.
14.1. UN number
-
14.2. UN proper shipping name
-
14.3. Transport hazard classes
-
14.4. Packing group
-
14.5. Environmental hazards
-

A.I. Schulze
®
®
®
Page 10 of 10
14.6. Special precautions for the user
-
14.7. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
-
SECTION 15: Regulatory information
15.1. Safety, health and environmental regulations / legislation specific for the substance or
mixture
The product is not a hazardous substance as defined by the Ordinance on Hazardous Substances and
by the relevant EC Directives (67/548/EEC and 88/379/EEC), as amended at the time of issuing the data
sheet.
15.2. Chemical safety assessment
Not relevant.
SECTION 16: Other information
Subs. 1: From safety data sheets for the individual components.
Safety data sheet as at 01.09.2012.Current download version at www.a-i-schulze.com.

Birkosit tds msds 2012

Recomendados

Recomendados

Mais conteúdo relacionado

Destaque

Destaque (20)

Semelhante a Birkosit tds msds 2012

Semelhante a Birkosit tds msds 2012 (20)

Mais de Project Sales Corp

Mais de Project Sales Corp (20)

Último

Último (20)

Birkosit tds msds 2012