1. Suların Arıtılması
Water Treatment
3. Su Alma Yapısı
Water Intake Structure
enve-muhammed.blogspot.com
2. Su Alma Yapısı Örnekleri
Water Intake Structures / Towers
Su Alma Kuleleri, Hoover Barajı – Las Vegas
enve-muhammed.blogspot.com
3. Su Alma Yapısı Örnekleri
Water Intake Structures / Towers
Su Alma Kuleleri, Talla Rezervuarı - UK
enve-muhammed.blogspot.com
4. Su Alma Yapısı Örnekleri
Water Intake Structures / Towers
Su Alma Kuleleri , Megget Rezervuarı - UK
enve-muhammed.blogspot.com
5. Su Alma Yapısı Örnekleri
Water Intake Structures / Towers
Su Alma Yapısı Çizimi, Ömerli İçme Suyu AT - İstanbul
enve-muhammed.blogspot.com
6. Su Alma Yapısının İşlevi
Intake Structure
Su alma yapısının temel işlevi suyun, kaynak üzerinde
önceden tespit edilmiş su seviyesinden güvenli bir
şekilde çekilmesi ve çekilen bu suyun arıtma tesisine
nakledilmesidir.
The basic function of the intake structure is to help in safely withdrawing water from the
source over predetermined pool levels and then to discharge this water into the
withdrawal conduit (normally called intake conduit), through which it flows up to water
treatment plant.
enve-muhammed.blogspot.com
7. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
Su alma yapısı için yer seçimi yapılırken aşağıdaki
faktörler göz önünde bulundurulmalıdır:
1. Su alma yapısı arıtma tesisine mümkün olduğunca
yakın seçilmelidir böylelikle suyun iletimi için
oluşacak maliyet daha az olacaktır.
1. As far as possible, the site should be near the treatment plant so that the cost of conveying
water to the city is less.
enve-muhammed.blogspot.com
8. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
2. Yapı, kaynaktan en iyi kalitedeki suyun temin
edilebilmesi için su kaynağının görece daha temiz bir
bölgesine yerleştirilmelidir, böylece arıtma tesisi
üzerindeki kirlilik yükü azalacaktır.
2. The intake must be located in the purer zone of the source to draw best quality water from
the source, thereby reducing load on the treatment plant.
enve-muhammed.blogspot.com
9. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
3. Su alma yapısı kesinlikle bir atıksu deşarj noktası
civarında olmamalıdır.
3. The intake must never be located at the downstream or in the vicinity of the point of disposal
of wastewater.
enve-muhammed.blogspot.com
10. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
4. Su alma yapısı için seçilecek yer gerektiğinde daha
yüksek debide su çekilmesine imkan verecek nitelikte
olmalıdır.
4. The site should be such as to permit greater withdrawal of water, if required at a future date.
enve-muhammed.blogspot.com
11. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
5. Yapı, yılın en kuru mevsiminde dahi kaynaktan su
çekmeye elverişli olmalıdır.
5. The intake must be located at a place from where it can draw water even during the driest
period of the year.
enve-muhammed.blogspot.com
12. Su Alma Yapısının Konumlandırılması
Factors Governing Location of Intake
6. Su alma yapısı yeri taşkın ya da sel gibi durumlarda
bile kolay bir şekilde ulaşılabilir olmalı taşkın ya da
sellerden etkilenmemeli, taşkın yada sel suları su alma
yapısı civarında yoğunlaşmamalıdır.
6. The intake site should remain easily accessible during floods and should noy get flooded.
Moreover, the flood waters should not be concentrated in the vicinity of the intake.
enve-muhammed.blogspot.com
13. Su Alma Seviyesi
Water Intake Level
Suyu;
- Kaynağın yüzeye fazla yakın bir noktasından alırsak
alg konsantrasyonu daha fazla olan bir ham su elde
etmiş oluruz.
- Dibe fazla yakın bir noktadan alırsak demir ve mangan
konsantrasyonu daha yüksek olan bir ham su elde
edebiliriz.
enve-muhammed.blogspot.com
15. Su Alma Seviyesi
Water Intake Level
Hareket ettirilebilir su alma yapısı ile su alma seviyesi ayarlanabilir. Movable intake (river)
enve-muhammed.blogspot.com
16. Tasarım
Design
Tasarımda dikkat edilecek hususlar
1. Güçlü akıntılar, yüzen maddeler, batık cisimler, buz
baskısı gibi dış etkenlere karşı bir emniyet faktörü
değerlendirilmelidir.
1. Sufficient factor of safety against external forces such as heavy currents, floating
materials, submerged bodies, ice pressure, etc.
enve-muhammed.blogspot.com
17. Tasarım
Design
Tasarımda dikkat edilecek hususlar
2. Su alma yapısı suyun hareketine mukavemet
edebilecek bir ağırlığa sahip olmalıdır.
2. Should have sufficient self weight so that it does not float by upthrust of water.
enve-muhammed.blogspot.com
18. Su Alma Yapısı
Su alma yapısı, su kaynağına bağlı olarak 2 şekilde
çalışabilir:
1. Pompalama
2. İletim
Types of Intake
Depending on the source of water, the intake works are classified as follows:
1. Pumping
2. Conveyence
enve-muhammed.blogspot.com
19. Pompalama
- Pompalamada, suyu yüksek basınçla daha düşük bir
seviyeden daha yüksek bir seviyeye çıkarmak için mekanik
enerjiyi hidrolik enerjiye çeviren pompalar kullanılır.
- Pompa kapasitesi= g*Q*H / E
(g: yerçekimi, Q: debi, H: toplam yük kaybı, E: verimlilik) formülü ile bulunur.
- Gerekli pompa sayısı, debinin pompa kapasitesine bölümü
sonucu bulunur.
- Pompa sayısı 2,4,.. gibi çift sayılarda seçilir ve yarısı yedek
olarak bırakılır.
enve-muhammed.blogspot.com
20. Pumping
- A pump is a device which converts mechanical energy into hydraulic energy. It lifts water
from a lower to a higher level and delivers it at high pressure.
- Efficiency of pump (E) = gQH/Brake H.P.
(g: gravity, Q: flowrate, H: total head, E: efficiency)
- Provide even number of motors say 2,4,... with their total capacity being equal to the total
BHP and provide half of the motors required as stand-by.
enve-muhammed.blogspot.com
21. İletim
Suyun iletiminde 2 aşama mevcuttur:
1. Suyun kaynaktan arıtma tesisine iletimi
2. Arıtılmış suyun tesisten dağıtım sistemine iletimi
İlk aşamada su pompalama yada yerçekimi (cazibe) yada
ikisinin birlikte kullanımıyla taşınır.
İkinci aşamada su önce bir toplama tankına pompalanıp
ardından cazibeyle yada doğrudan pompalamayla
dağıtıma iletilir.
enve-muhammed.blogspot.com
22. Conveyence
There are two stages in the transportation of water:
1. Conveyance of water from the source to the treatment plant.
2. Conveyance of treated water from treatment plant to the distribution system.
In the first stage water is transported by gravity or by pumping or by the combined action of
both, depending upon the relative elevations of the treatment plant and the source of supply.
In the second stage water transmission may be either by pumping into an overhead tank and
then supplying by gravity or by pumping directly into the water-main for distribution.
enve-muhammed.blogspot.com
23. İletim
Conveyence
Serbest Akış
Bu sistemde iletim hattındaki su yüzeyi cazibe ile serbestçe
akar. Böyle bir iletim hattında hidrolik gradyen çizgisi su
yüzeyi ile çakışır.
Genellikle mevcut taban eğimi ile uygun olması için çok uzun
iletim hatları inşa edilmelidir. Kanallar, su yolları, dereceli
tüneller ve su kemerleri örnek olarak verilebilir.
Free Flow System
In this system, the surface of water in the conveying section flows freely due to gravity. In such a conduit the
hydraulic gradient line coincide with the water surface and is parallel to the bed of the conduit. It is often
necessary to construct very long conveying sections, to suit the slope of the existing ground. The sections used
for free-flow are: Canals, flumes, grade aqueducts and grade tunnels.
enve-muhammed.blogspot.com
24. İletim
Conveyence
Basınçlı Akış
Basınçlı (kapalı) iletim hatlarında su, atmosfer basıncının üzerindeki
bir basınç altında akar. Bu sebeple su hidrolik gradyen çizgisinden
bağımsızdır ve mevcut doğal yüzey eğimine tabi olarak akar
dolayısıyla daha az iletim hattı mesafesi gerektirir.
Yapıldığı malzemeye göre basınçlı borular dökme demir, çelik, RCC,
vitrifiye kil, asbest çimento, işlenmiş demir, bakır, pirinç, kurşun,
plastik, cam destekli plastik boru vb. olabilir.
Pressure System
In pressure conduits, which are closed conduits, the water flows under pressure above the atmospheric pressure. The bed
or invert of the conduit in pressure flows is thus independent of the grade of the hydraulic gradient line and can, therefore,
follow the natural available ground surface thus requiring lesser length of conduit.
Depending upon the construction material, the pressure pipes are of following types: Cast iron, steel, R.C.C, hume steel,
vitrified clay, asbestos cement, wrought iron, copper, brass and lead, plastic, and glass reinforced plastic pipes.
enve-muhammed.blogspot.com
25. Hidrolik Tasarım
Su iletim hatları tasarımında genellikle açık akışlar için Manning ve
basınçlı akışlar için Hazen-William formülleri kullanılır.
Manning Formülü
U=1/n rH2/3S1/2
U: hız ( m/sn) , rH: hidrolik yarıçap, S: eğim, n: Manning katsayısı
In the design of water supply conduits , generally, Hazen-William's formula for pressure conduits and
Manning's formula for free flow conduits are used. Manning's formula
U=1/n rH2/3S1/2
where, U= velocity, m/s; rH= hydraulic radius,m; S= slope, and n = Manning's coefficient.
enve-muhammed.blogspot.com
26. Hidrolik Tasarım
Hazen-William Formülü
U=0.85 C rH0.63S0.54
U: hız ( m/sn) , rH: hidrolik yarıçap, S: eğim, C: Hazen- William katsayısı
Hazen-William's formula
U=0.85 C rH0.63S0.54
U= velocity, m/s; rH= hydraulic radius,m; S= slope, C= Hazen-William's coefficient
enve-muhammed.blogspot.com
27. Referanslar
References
1. http://nptel.iitm.ac.in/courses/Webcourse-contents/IIT-KANPUR/wasteWater/Lecture%203.htm
2. http://www.suatiksu.org/wp-content/uploads/2010/07/WTP-Lecture-1b-Water-Intake-Structures.pdf, A.
Mete Saatçi
3. Tanzanya Su bakanlığı – Rwegarulila Su Kaynakları Enstitüsü,
http://www.fastonline.org/CD3WD_40/CD3WD/WATSAN/H0322E/EN/B1193_4.HTM
4. http://farm1.static.flickr.com/191/456043645_8cb12492ef.jpg
5. http://en.wikipedia.org/wiki/File:TallaReservoir.jpg
6. http://www.geograph.org.uk/photo/1194290
enve-muhammed.blogspot.com