This document provides step-by-step instructions for assembling an All In One Training system with an Intel DH61AG motherboard. Key steps include installing the motherboard, CPU, memory, hard drive, optical drive, fan, and connecting various cables. Special attention is required when setting jumpers to provide power to the flat panel display and using the Integrator Toolkit to enable the BIOS to recognize the display.

1. All In One Training
ASI ECS G11 Assembly
1

2. Getting Started
Lay the system face down making sure not to damage
screen

3. Remove Back Cable Cover
Press Tab and Pull off

4. Remove Back Cover
Undo the five screws holding the cover on
Slide to Left, this requires a little force
One under the
cable cover

5. DH61AG Motherboard
DH61AG DH61AG SATA Power cable
DH61AG IO Shield

6. Insert ½ Height I/O Shield
Remove from the DH61AG box and place in chassis

7. Place Backing Plate on Board
Peel off the self-adhesive strip covers from the backing plate
that comes with the chassis and affix it to the bottom of the
motherboard as shown

8. Mount Motherboard
Place the motherboard in the chassis being careful to make
sure the I/O shield pins clear the sockets on the
motherboard. Secure with 4 screws.

9. Open the CPU Socket
Press down on the CPU socket locking lever and swing the
socket frame open. Remove processor cover.

10. Insert CPU
Carefully align the CPU in the socket using the cutout guides
on the processor. Close and secure the locking mechanism.

11. Install the Wireless Card
Locate the ½ length mini PCIe slot at #7. CAREFULLY (they
can be stripped) remove the two mini Phillips screws and
place the card edge in the slot. Secure with the mini screws.

12. Install the mSATA SSD
Locate the full length mini PCIe slot at #15. Make sure the
posts fit tightly. CAREFULLY (do not strip) remove the mini
Phillips head screws. Insert the mSATA SSD and screw
down.

13. Install the Speaker & Audio Header
Plug in the 1x4 speaker header in the keyed socket at #10.
Plug in the front audio header to the yellow set of pins next
to the PCIe slot at #12.

14. Installing the Antenna
Take the antenna lead from the lower part of the case and
attach the mini BNC connector to the left post. Attach the
antenna lead from the top of the right post on the wireless
card.

15. Connect the FP Switch/LED
Plug the front panel switch/LED connector to point #5 on the
side of the board.

16. Connect the LCD Brightness Hdr
Connect the keyed LCD brightness plug next to the LVDS
header in the area marked #14

17. Plug in the SODIMM Memory
Lay the SODIMM at #2 into the lower memory socket and
make sure you lock in place.

18. Plug in the Dual FP USB
Plug in the keyed front panel USB connector to the USB
socket marked #11 to the right.

19. Plug in the Camera and Panel
• Locate the two 1x5 cables (one is grey the other is
black
• These cables will attach to the dual lane USB on the
board edge next to the processor socket.
• The dual lane USB pins have 5 pins across one side
and four on the other.
• You will need to “punch out” only one of the blocks
on the cable so it can go across the pins (top row
has 5 bottom has 4 in each case the “fifth” pin is
dead.
• Attach both 1X5 cables across the 2x5 USB
connector.

20. Plug in the Camera and Panel (cont)
• First cable

21. Plug in the Camera and Panel (cont)
• Second cable

22. Plug In the System Fan
Plug the keyed system fan connector to #4 on the board.

23. Plug In the Touch Panel
Plug the 1x5 connector to # 6 with the “dead” pin to the right.

24. Remove the HDD Tray
Remove the two screws on the side of the HDD tray and
slide to the left to remove

25. Mount HDD in Tray
Use the silver flat headed Phillips screws with the long posts
through the rubber grommets on the HDD carrier to mount
the HDD. Make sure it is in upside down with the connectors
opposite the edge of the chassis. Replace carrier in chassis

26. Mount the “L” Bracket on ODD
Screw the “L” bracket to the back of the ODD with the tiny
Phillips screw. Orient the bracket with “L” toward the bottom
and the angled slot to the right.

27. Mount the ODD
Remove the cover plate for the ODD slot by pressing down
on the notched center section and lifting the two tabs (the
cover is removed by pushing back in the case. Slide the
ODD through the slot and secure the “L” bracket at the back
to the chassis with a single screw.

28. Special SATA Power cable
Adapter cable for slim ODD

29. Locate the SATA Power Cable
Look for the cable that has an “L” connection at one end and
a pair of SATA power connections and one large 1x4 Molex
power connector

30. Plug In the SATA Power Cable
Plug the “L” SATA connector into the board at #17. Then
plug one SATA power connector into the HDD.

31. ODD SATA Power & Data Cable
Locate the ODD SATA power & data cable and plug the
combo end to the ODD. Connect the 1x4 receptacle to the
corresponding socket on the HDD power cable. Plug the
SATA data cable to the front socket at #17

32. HDD SATA Data Cable
Plug the HDD SATA cable into the back of the HDD. Plug
the “L” connector at the other end into the second socket at
#17

33. Place the Processor Heat Pipe
Place the heat pipe on the processor socket as shown. Make
sure the cooling fins fit into the space provided. Tighten the
four spring loaded screws until the heat pipe is firmly seated.
Align the fan with the cooling fins and screw down at 3
points.

34. Attach the Heat Pipe Fan Header
Plug in the heat pipe fan to #3

35. Do Not Plug In the LVDS Header
• You will need to use the Integrator Tool Kit (ITK) to set the
BIOS to use the flat panel display connected through the
LVDS header.
• The next step is very important. You must correctly set the
power for the flat panel LVDS display

36. Set the Power Jumpers for LVDS
Back in the area marked #14 there are two blocks at
opposite ends with jumpers. The one to the left is a 1x3. Set
this across the two right pins. The other is a 2X3 with two
pins missing. Set this jumper across the back two furthest to
the right. Each is marked with an

37. Connect the DVI Monitor
• Before you can use the built-in flat panel (LVDS) display,
you will have to use the Intel Integrator Tool Kit (ITK) to
enable the BIOS (the default is no LVDS device installed).
• Also plug in the USB keyboard and power supply
• Plug in the DOS bootable USB thumb drive with the DOS
version of the ITK.

38. Hit F2 to Enter the BIOS
• Scroll over to the “Boot” tab
• Scroll down to “Boot to Removable Devices” and make
sure it reads <Enable>
• Scroll down to “Boot USB Devices First set to <Enable>
• Plug in the DOS bootable USB thumb drive with the DOS
version of the Integrator Tool Kit (ITK)
• Press the F10 key “Exit Saving Changes (Y/N)” and press
“Y” the system will reboot to the USB key

39. Using the ITK for DOS
• When you see the “C:” prompt type in the following (the
command is case sensitive, so type exactly as shown) and
hit “Enter”
• itoolkit EXTRACT –config –tokens –ini=ag_g11.ini
• The EXTRACT command creates a visual file with the
various BIOS commands/functions.
• The screen will look similar to this

40. Modify the ag_g11.ini File part 1
• Boot your laptop and plug the bootable USB key into it
• Use “Wordpad” to edit the g11.ini file
• Use CTRL F command and find IGD Flat Panel
• Change the “Value” from 0:Disable to 1:LVDS

41. Modify the ag_g11.ini File part 2
• Use CTRL F command and find Pre-Defined EDID
• Change the Value from 3 to 15 (1080P)

42. Modify the ag_g11.ini File part 3
• Use CTRL F command and find IGD Secondary Video
Port
• Change the Value from 0 : None to 3 : DVI-I Digital
; IGD Secondary Video Port
;---------------------------------------
; Select a single value from this list:
; 0 : None (default)
; 2 : DVI-I (Blue) Analog
; 3 : DVI-I (Blue) Digital
; 5 : HDMI
Value=3

43. Modify the ag_g11.ini File part 4
• Use CTRL F command and find Screen Brightness
• Change the Value to 6 : Brightest
; Screen Brightness
;-------------------------------
--------
; Select a single value from
this list:
; 0 : Dimmest (default)
; 1 : Dimmer
; 2 : Dim
; 3 : Neutral
; 4 : Bright
; 5 : Brighter
; 6 : Brightest
Value=6

44. Modify the ag_g11.ini File part 5
• Save the file as ag_g11.ini to the bootable USB drive and
exit Wordpad.
• Open the ag_g11.ini file and check that the changes were
saved. If not, repeat the 4 steps. If done, exit the program
remove the bootable USB drive and plug it back into the
g11 system then boot the g11 to the USB drive.

45. Updating the BIOS with ITK
• At the C: prompt type the following command (case
sensitive)
• Itoolkit INSTALL –config –tokens –ini=ag_g11.ini
• The INSTALL command will write your modifications to the
BIOS
• Hit the enter key and your screen should look similar to this

46. Turn Off the System
• Unplug the power supply and the DVI monitor
• Remove the bootable USB drive
• Gently push the LVDS cable into its receptacle on the
board in area #14. Use the edges and avoid pushing on
the wires.

47. Booting the Flat Panel Display
• Plug in the power supply and start the system
• The LCD flat panel should be on

48. Install the Stand
• Using the six screw points from the inside of the back
cover, secure the stand
• Slide the cover on the back of the system. Screw in the five
points to secure the chassis. Plug in the power, replace
cable cover