1. Have you got slippery floors inside or outside?
HALO ANTI SLIP
ADVANCED NANO COATINGS
Clever coatings at the cutting edge
Used in the following locations:
SkyCity toilets
Aotea Centre exterior pavers
Retirement village poolside
Auckland Hospital main entrance
AA Office building entry lobby
St John Ambulance entry
Geyser Building walkways
Middlemore Hospital
Other anti‐slips
rely on etching
which ruins the
substrate. Halo
does not
$25/m2
applied
Apply over any
substrate – even
wood, porcelain
tiles, or vinyl
Suitable for:
Any existing or new surface.
Wood/ Tiles/ Concrete/ Vinyl/ Pavers
Locations suitable:
Retirement villages
Education facilities
Office & commercial building lobbies
Carparks
Slip
co‐efficiency of 0.59
allows you to
make any substrate
anti‐slip

2. Halo SV Anti-slip
HALO SURFACES INTERNATIONAL LIMITED
COATINGS from Halo Surfaces
International Ltd are sensitive to
the environment.
Surface Preparation
Instructions
The surface must be clean, dry and in
sound condition. Remove all oil, dust,
grease and dirt using Halo Degreaser.
Rinse thoroughly with fresh water and
allow to dry. The moisture content must not
exceed 13%. It is vital that a floor that has
retained oil must be completely free from
wicking or a bond will not form and the
coating will delaminate.
Unsealed floors must be sealed and
Halo SV Enhancer Plus Sealer is strongly
recommended as it is formulated to bond
with Halo SV Enhancer Plus Sealer and
dries in 5 minutes.
Both new and previously painted surfaces
should be sanded to 220 grit before
applying Halo SV Anti-slip.
Remove all silicone sealers using Halo
Degreaser.
Test whether the surface is ready to coat
by sprinkling water onto the surfaces. If
the water beads, there is a sealer present
which must be removed before re-sealing
with Halo SV Enhancer Plus Sealer and
applying Halo SV Anti-slip.
Mask off adjacent areas.
Application Instructions
TEST: Because there are many
differences in substrates always test Halo
SV Anti-slip in an inconspicuous area to
ensure compatibility and performance and
the desired finish.
APPLICATION: Apply Halo SV Anti-slip
in an ambient temperature between 7-40
degrees Celsius, 90% RH or less, and, if
applying outdoors make sure that there
will be no rain or dew for 5 hours after
completing the coating process.
Product Description
Halo SV Anti-slip is a clear thin
protective coat containing mesh
beads for concrete, masonry
and tiled floors. It has been
formulated using the principles
of Halo Matrix-Nano™ controlled
chemical nanotechnology and is
peel and flake resistant. It can be
applied over Halo SV Enhancer
Plus Sealer to provide an anti-slip
coating system that is easy and
quick to apply and cost-effective.
Use on these substrates
Concrete and masonry floors,
masonry pavers, tiles, bricks and
cement blocks.
Solve these problems
Halo SV Anti-slip protects
against moisture and chloride ion
penetration, food and beverage
acids, bird and animal waste matter,
salt-spray, gum and graffiti. It also
provides protection against falling or
slipping on slippery surfaces.
Wind may affect the quality of the finish
and it may be necessary to erect a wind-
shield.
THOROUGHLY STIR the contents of the
container for several minutes (or shake it
thoroughly if the container is small) Re-stir
or re-shake the container every 15-20
minutes to ensure the nano particles
remain suspended.
Add 320 mesh glass beads supplied
separately to Halo SV Anti-slip at a ratio
of 100 grams of beads per litre of coating.
A more even finish will be achieved by
spraying the coating. Keep stirring the
mixture to ensure the beads do not clump
together.
Halo SV Anti-slip may be sprayed or
rolled.
Spraying: Use a portable alcohol and
acetone-proof sprayer with a grey or red
tip or an HVLP spray gun with a 1.0 size
tip and the pressure set at approximately
25 psi.
Spray test-patterns until you achieve an
elongated pattern 20-25 cm long and 5
cm wide in the middle with sufficient fluid
to cover but not to puddle. Work with a
waste bucket so that you start and finish
your spraying in the bucket and avoid
drips on the surface being coated. Hold
the tip of the HVLP gun or pump-sprayer
20-25 cm square from the surface. Apply
one coat in a cross-hatch or circular
pattern to provide sufficient coverage
without holes.
Rolling: Use an ultra-smooth high-density
foam roller and apply Halo SV Anti-slip
as quickly as possible in a cross-hatch
pattern always keeping a wet edge. Make
sure the roller is saturated at all times but
do not press down on the roller or over-
work the coating.
A second coat: Do not apply a second
coat unless there is a flaw in the
application of the first coat. In that case,
wait 24 hours, and then sand the surface
to 220 grit, clean and reapply.
Keep the lid on the tin to stop evaporation.
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited

3. Halo SV Anti-slip gained an average of .59 when tested
by the wet pendulum method in New Zealand.
The building code requires a .4.
Halo SV Anti-slip is a gloss
finish
Glass beads may only be added to Halo
SV gloss finishes not satin.
Drying time
At 21 degrees Celsius 50% RH: Touch dry
2 hours; dry through 2-6 hours; walk on
10 – 12 hours; full cure 7 days.
Interruption of Work
As treated and untreated surfaces look
similar, finish work on an obvious point
such as a corner or mark where you have
stopped.
Cleaning Up
Clean tools and equipment immediately
with acetone.
Care and Maintenance
Clean with a mop and Halo Multi-purpose
Cleaner then rinse with fresh water. On a
large commercial floor use a floor-cleaning
machine in wash-mode using Halo Multi-
purpose Cleaner as the cleaning agent. A
soft non-abrasive pad may be used to buff
the floor for a shiny finish.
If Halo SV Anti-slip is damaged, lightly
sand the coating to 220 grit and reapply.
Product Characteristics
Colour: slight amber to rose in the tin but
dries clear
Finish: Gloss or Satin
Base Material: Solvent
Flash Point: -9C (C Pensky-Martens
Closed Cup)
VOCs: less than 100g/L
Weight: 880 gms/L
Non-breathable
Coverage
12-15 sq m per litre (non-porous surfaces)
7-12 sq m per litre (porous surfaces)
Spread Rate
Wet: 50-75 microns
Dry: 40-60 microns
Testing
ASTM D
– 3363
Film Hardness Taber; 39.11
average
NZ Wet
Pendulum
Anti-slip Coating .59 average
against Code Requirements
of .4
Hazmat Information
Coating Solution UN#1139,
Class 3, Packing Group III.
Warranty
Halo Surfaces International Ltd
guarantees Halo SV Anti-slip
to be defect-free. All material
proven defective will be replaced
within 5 years of date and proof
of purchase. The warranty
is for defective product only
and does not cover wear and
tear or application not carried
out in accordance with these
instructions and any other related
guidelines on the company’s
website www.halosurfaces.com.
This warranty is given in lieu of
all other warranties, express or
implied including warranty of
merchantability or fitness for
purpose.
The remedy contained in this
warranty is an exclusive remedy
and Halo Surfaces International
Ltd shall not be responsible for
any other damages including
labour or any incidental,
consequential, special or punitive
damages whatsoever.
Warnings
FLAMMABLE LIQUID: contains
TBA and Ethyl Alcohol.
If in an enclosed area you must
have fresh air supply and exhaust.
You must wear an approved
respirator.
Wear butyl-rubber gloves.
Wear safety goggles. Do not rely
on contact lenses to protect eyes.
Avoid open flames and ignition
sources. The fumes are flammable.
If splashed on skin, wash
thoroughly with soap and water.
If coating gets into eyes, flush with
water for 15 minutes. If irritation
continues obtain medical attention.
If swallowed, rinse mouth with
water and obtain immediate
medical attention.
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited

4. Ingredient C.A.S Number Concentration ACGIH TLV OSHA PEL
Trade Secret A-1 Proprietary 23-25 1000 ppm n/a
Trade Secret A-2 Proprietary 9-10 10 ppm 100 ppm
Ethyl Alcohol 64-17-5 9-10 1000 ppm 1000 ppm
Butyl Acetate 540-88-5 36-39 200 ppm 200 ppm
Trade Secret B Proprietary 13-16 n/a n/a
COMPOSITION/INFORMATION ON INGREDIENTS
HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE
INHILATION of vapour or spray mist
EYE or SKIN contact with the product, vapour,
or spay mist
EFFECTS OF OVEREXPOSURE
EYES: irritation, redness
SKIN: irritation, redness
INHILATION: headaches or dizziness
FIRST AID MEASURES
Eyes: Immediately flush eyes with plenty of
water for at least 15 minutes. Get medical
attention.
Skin: In case of skin contact, wash thoroughly
with soap and water. Remove contaminated
clothing and shoes.
Do not use organic solvents for cleanup as
they may dry or irritate the skin and act as a
carrier for chemical
absorption.
Inhalation: If aerosol or mists are formed,
remove affected person to fresh air. Seek
immediate medical attention if breathing
difficulties occur. Also keep patient half sitting
with upper body raised.
2
3
4
Ingestion: If accidentally swallowed, rinse
mouth thoroughly with water and, afterwards,
drink plenty of water.
In case of discomfort, obtain medical
attention. Notes to physician: If substance
has been swallowed obtain early endoscopy
in order to assess mucosa lesions in the
esophagus and stomach, which may appear.
If necessary, aspirate leftover substance.
DATE OF PREPARATION
March 1, 2014
Safety Data Sheet
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited
Halo SV Anti-slip CoatHALO SURFACES INTERNATIONAL LIMITED
Product Name Halo SV Anti-slip Coat
Product Code HSIL 72
Medical Emergency New Zealand 111
1 COMPANY & PRODUCT INFORMATION
Halo Surfaces International Limited
P O Box 90 109
Victoria Street West MC
Auckland 1142
NEW ZEALAND

5. 5 SECTION 5-FIREFIGHTING MEASURES
ACCIDENTAL RELEASE
MEASURES
HANDLING AND STORAGE
PHYSICAL AND CHEMICAL PROPERTIES
Vapour PRESSURE: 9 hPa @ 20° C
Vapour DENSITY: Heavier than air
SPECIFIC GRAVITY: 1.02
BOILING POINT: >90°C
SOLUBILITY IN WATER: Insoluble
APPEARANCE: Clear to slightly milky liquid
6 7
9
ODOR: Mild fruity
VOLATILE ORGANIC COMPOUNDS:
<100 g/l
Flash Point LEL WEL Famility Classification
CLOSED CUP:
25 °C (77°F).
Not Sure Not Sure RED LABEL -- Flammable,
Flash below 100 °F (38 °C)
EXTINGUISHING MEDIA
Use water spray, foam, dry chemical, or CO2
UNUSUAL FIRE & EXPLOSION HAZARDS
Hazardous fumes (ethanol, phenolics, oxides
of carbon and nitrogen) may be evolved upon
exposure to heat or open flame.
SPECIAL FIRE FIGHTING PROCEDURES
N/A
Dike area to prevent spreading. Absorb on
vermiculite, sand or other inert absorbing
material. Dispose of as a chemical waste
in accordance with current local, state and
federal regulations.
DOT STORAGE CLASS: Class 3
PROPER DOT SHIPPING NAME:
Coating Solution
HANDLING: Provide good ventilation or
extraction. Avoid prolonged or repeated
breathing of vapour. Avoid contact with eyes,
skin and clothing. Keep away from heat,
sparks, flames and other sources of ignition.
Wash hands thoroughly after handling.
STORAGE: Avoid storage over 100° F,
contamination with incompatible materials.
Keep containers tightly closed in a cool, well
ventilated place.
Protect from moisture. Residual vapours
might explode on ignition. Do not apply heat,
cut, drill, and grind or weld on or near this
container.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
PRECAUTIONS TO BE TAKEN IN USE
Use only with adequate ventilation. Avoid
contact with skin and eyes. Avoid breathing
vapour and spray mist. Wash hands after
using.
VENTILATION SYSTEM
Positive fresh air exhaust should be provided
in the work area. A respiratory protection
2 of 4
program that meets OSHA 1910.134 and
ANSI Z88.2 or applicable federal/provincial
requirements must be followed whenever
workplace conditions warrant respirator use.
SKIN PROTECTION
Avoid skin contact. Wear butyl-rubber gloves
and impervious protective clothing.
EYE PROTECTION
Do not wear contact lenses. Chemical safety
goggles or splash shields are recommended.
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited

6. STABILITY AND REACTIVITY
TOXICOLOGICAL INFORMATION
DISPOSAL CONSIDERATIONS
Whatever cannot be saved for recovery or
recycling should be handled as hazardous
waste and sent to a RCRA approved
incinerator or disposed in a RCRA approved
waste facility.
Processing, use or contamination of this
product may change the waste management
options. State and local disposal regulations
may differ from federal disposal regulations.
Dispose of container and unused contents
in accordance with federal, state and local
requirements.
ABBREVIATIONS:
IRR = Irritant
LIV = Liver
KID = Kidney
ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
No data available
3 of 4
STABILITY: Stable
HAZARDOUS DECOMPISITION
PRODUCTS: Ethanol
INCOMPATABILITIES: Oxidizers, alkalis,
acids, aliphatic amines, nitrates, water
HAZARDOUS POLYMERIZATION: May occur
Ingredient Target Organs IARC CATEGORY
Trade Secret A-1 IRR, LIV, KID NO
Trade Secret A-2 IRR, LIV, KID NO
Ethyl Alcohol HEART, IRR, LIV, KID NO
Butyl Acetate IRR NO
Trade Secret B NONE NO
10
11
12
13
TRANSPORT INFORMATION
DOT AND IATA HAZARD CLASSIFICATION:
Class 3 Flammable Liquid
14
PROPER DOT SHIPPING NAME:
Coatings Solution
IDENTIFICATION NUMBER:
DOT – UN 1139 IATA – UN 1139
REGULATORY INFORMATION
SARA 313 (40 CFR 372.65C)
SUPPLIER NOTIFICATION
15
CALIFORNIA PROPOSITION 65
This product does not contain chemicals
known to the State of California to cause
cancer and birth defects or
other reproductive harm.
CAS number Chemical Compound
64-17-5 Ethyl Alcohol
540-88-5 Butyl Acetate
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited

7. OTHER INFORMATION
This product has been classified in
accordance with the hazard criteria of the
Canadian Controlled Products Regulations
(CPR) and the SDS contains all of the
information required by the CPR.
IMPORTANT LIABILITY DISCLAIMER:
The information contained in this Safety Data
Sheet (SDS) is believed to be correct as it was
obtained from sources we believe are reliable.
However, no representations, guarantees
or warranties of any kind are made as to its
accuracy, suitability for particular applications,
hazards connected with the use of the
material, or the results to be obtained from the
use thereof.
User assumes all risks and liability of any use,
processing or handling of any material,
variations in methods, conditions and
equipment used to store, handle or process
the material and hazards connected with the
use of the material are solely the responsibility
of the user and remain at his sole discretion.
Compliance with all applicable federal, state,
and local laws and regulations remains the
responsibility of the user, and the user has the
responsibility to provide a safe work place,
to examine all aspects of its operation and to
determine if or where precautions, in addition
to those described herein, are required.
16
4 of 4
………end of SDS………
Sales and support +64 9 376 7099 | office@halosurfaces.com.Halo Surfaces International Limited