SlideShare uma empresa Scribd logo
1 de 41
Baixar para ler offline
1
Pumps & PumpingPumps & Pumping
SystemsSystems
By
SUDHIR REDDY S.V.R
M.TECH(CAD/CAM)
2
©© UNEP 2006UNEP 2006
Training Agenda: PumpsTraining Agenda: Pumps
Introduction
Type of pumps
Assessment of pumps
Energy efficiency opportunities
ElectricalEquipment/
Pumps
3
©© UNEP 2006UNEP 2006
IntroductionIntroduction
• 20% of world’s electrical energy
demand
• 25-50% of energy usage in some
industries
• Used for
• Domestic, commercial, industrial and
agricultural services
• Municipal water and wastewater services
What are Pumping Systems
ElectricalEquipment/
Pumps
4
©© UNEP 2006UNEP 2006
IntroductionIntroduction
Objective of pumping system
What are Pumping Systems
ElectricalEquipment/
Pumps
(US DOE, 2001)
• Transfer liquid
from source to
destination
• Circulate liquid
around a system
5
©© UNEP 2006UNEP 2006
IntroductionIntroduction
• Main pump components
• Pumps
• Prime movers: electric motors, diesel engines,
air system
• Piping to carry fluid
• Valves to control flow in system
• Other fittings, control, instrumentation
• End-use equipment
• Heat exchangers, tanks, hydraulic machines
What are Pumping Systems
ElectricalEquipment/
Pumps
6
©© UNEP 2006UNEP 2006
IntroductionIntroduction
• Head
• Resistance of the system
• Two types: static and friction
• Static head
• Difference in height between
source and destination
• Independent of flow
Pumping System Characteristics
ElectricalEquipment/
Pumps
destination
source
Stati
c
head
Static
head
Flow
7
©© UNEP 2006UNEP 2006
IntroductionIntroduction
• Static head consists of
• Static suction head (hS): lifting liquid relative to
pump center line
• Static discharge head (hD) vertical distance
between centerline and liquid surface in
destination tank
• Static head at certain pressure
Pumping System Characteristics
ElectricalEquipment/
Pumps
Head (in feet) = Pressure (psi) X 2.31
Specific gravity
8
©© UNEP 2006UNEP 2006
IntroductionIntroduction
• Friction head
• Resistance to flow in pipe and fittings
• Depends on size, pipes, pipe fittings, flow
rate, nature of liquid
• Proportional to square of flow rate
• Closed loop system
only has friction head
(no static head)
Pumping System Characteristics
ElectricalEquipment/
Pumps
Friction
head
Flow
9
©© UNEP 2006UNEP 2006
IntroductionIntroduction
In most cases:
Total head = Static head + friction head
Pumping System Characteristics
ElectricalEquipment/
Pumps
System
head
Flow
Static head
Friction
head
System
curve
System
head
Flow
Static head
Friction
head
System
curve
10
©© UNEP 2006UNEP 2006
Training Agenda: PumpsTraining Agenda: Pumps
Introduction
Type of pumps
Assessment of pumps
Energy efficiency opportunities
ElectricalEquipment/
Pumps
11
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Classified by operating principle
Pump Classification
ElectricalEquipment/
Pumps
Dynamic
Positive
Displacement
Centrifugal Special effect Rotary Reciprocating
Internal
gear
External
gear
Lobe
Slide
vane
Others (e.g.
Impulse, Buoyancy)
Pumps
Dynamic
Positive
Displacement
Centrifugal Special effect Rotary Reciprocating
Internal
gear
External
gear
Lobe
Slide
vane
Others (e.g.
Impulse, Buoyancy)
Pumps
12
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Positive Displacement Pumps
ElectricalEquipment/
Pumps
• For each pump revolution
• Fixed amount of liquid taken from one end
• Positively discharged at other end
• If pipe blocked
• Pressure rises
• Can damage pump
• Used for pumping fluids other than
water
13
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Positive Displacement Pumps
ElectricalEquipment/
Pumps
• Reciprocating pump
• Displacement by reciprocation of piston
plunger
• Used only for viscous fluids and oil wells
• Rotary pump
• Displacement by rotary action of gear, cam or
vanes
• Several sub-types
• Used for special services in industry
14
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Dynamic pumps
ElectricalEquipment/
Pumps
• Mode of operation
• Rotating impeller converts kinetic energy into
pressure or velocity to pump the fluid
• Two types
• Centrifugal pumps: pumping water in
industry – 75% of pumps installed
• Special effect pumps: specialized conditions
15
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Centrifugal Pumps
ElectricalEquipment/
Pumps
How do they work?
(Sahdev M)
• Liquid forced into
impeller
• Vanes pass kinetic
energy to liquid: liquid
rotates and leaves
impeller
• Volute casing converts
kinetic energy into
pressure energy
16
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Centrifugal Pumps
ElectricalEquipment/
Pumps
Rotating and stationary components
(Sahdev)
17
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Centrifugal Pumps
ElectricalEquipment/
Pumps
Impeller Sahdev)
• Main rotating part that provides centrifugal
acceleration to the fluid
• Number of impellers = number of pump stages
• Impeller classification: direction of flow, suction type
and shape/mechanical construction
Shaft
• Transfers torque from motor to impeller during pump
start up and operation
18
©© UNEP 2006UNEP 2006
Type of PumpsType of Pumps
Centrifugal Pumps
ElectricalEquipment/
Pumps
Casings
Volute Casing (Sahdev)
• Functions
• Enclose impeller as “pressure vessel”
• Support and bearing for shaft and impeller
• Volute case
• Impellers inside casings
• Balances hydraulic pressure on pump shaft
• Circular casing
• Vanes surrounds impeller
• Used for multi-stage pumps
19
Impeller Mechanism PumpImpeller Mechanism Pump
20
Diaphragm PumpDiaphragm Pump
21
Gear PumpGear Pump
22
Gear Pump BalancedGear Pump Balanced
23
Vane PumpVane Pump
24
Piston PumpPiston Pump
25
Bent Axis Piston PumpBent Axis Piston Pump
26
Swash Plate Piston PumpSwash Plate Piston Pump
27
©© UNEP 2006UNEP 2006
Training Agenda: PumpsTraining Agenda: Pumps
Introduction
Type of pumps
Assessment of pumps
Energy efficiency opportunities
ElectricalEquipment/
Pumps
28
Assessment of pumpsAssessment of pumps
• Pump shaft power (Ps) is actual horsepower
delivered to the pump shaft
• Pump output/Hydraulic/Water horsepower (Hp) is
the liquid horsepower delivered by the pump
How to Calculate Pump Performance
ElectricalEquipment/
Pumps
Hydraulic power (Hp):
Hp = Q (m3/s) x Total head, hd - hs (m) x ρ (kg/m3) x g (m/s2) / 1000
Pump shaft power (Ps):
Ps = Hydraulic power Hp / pump efficiency ηPump
Pump Efficiency (ηPump):
ηPump = Hydraulic Power / Pump Shaft Power
©© UNEP 2006UNEP 2006
hd - discharge head hs – suction head,
ρ - density of the fluid g – acceleration due to gravity
29
©© UNEP 2006UNEP 2006
Assessment of pumpsAssessment of pumps
• Absence of pump specification data
to assess pump performance
• Difficulties in flow measurement and
flows are often estimated
• Improper calibration of pressure
gauges & measuring instruments
• Calibration not always carried out
• Correction factors used
Difficulties in Pump Assessment
ElectricalEquipment/
Pumps
30
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
1. Selecting the right pump
2. Controlling the flow rate by speed
variation
3. Pumps in parallel to meet varying
demand
4. Eliminating flow control valve
5. Eliminating by-pass control
6. Start/stop control of pump
7. Impeller trimming
ElectricalEquipment/
Pumps
31
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
1. Selecting the Right Pump
ElectricalEquipment/
Pumps
Pump performance curve for centrifugal
pump
BEE India,
2004
32
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
1. Selecting the Right Pump
ElectricalEquipment/
Pumps
• Oversized pump
• Requires flow control (throttle valve or by-
pass line)
• Provides additional head
• System curve shifts to left
• Pump efficiency is reduced
• Solutions if pump already purchased
• VSDs or two-speed drives
• Lower RPM
• Smaller or trimmed impeller
33
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
2. Controlling Flow: speed
variation
ElectricalEquipment/
Pumps
Explaining the effect of speed
• Affinity laws: relation speed N and
• Flow rate Q α N
• Head H α N2
• Power P α N3
• Small speed reduction (e.g. ½) = large
power reduction (e.g. 1/8)
34
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency OpportunitiesElectricalEquipment/
Pumps
Variable Speed Drives (VSD)
• Speed adjustment over continuous
range
• Power consumption also reduced!
• Two types
• Mechanical: hydraulic clutches, fluid couplings,
adjustable belts and pulleys
• Electrical: eddy current clutches, wound-rotor
motor controllers, Variable Frequency Drives
(VFDs)
2. Controlling Flow: speed
variation
35
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency OpportunitiesElectricalEquipment/
Pumps
Benefits of VSDs
• Energy savings (not just reduced flow!)
• Improved process control
• Improved system reliability
• Reduced capital and maintenance
costs
• Soft starter capability
2. Controlling Flow: speed
variation
36
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
3. Parallel Pumps for Varying
Demand
ElectricalEquipment/
Pumps
• Multiple pumps: some turned off during low
demand
• Used when static head is >50% of total head
• System curve
does not change
• Flow rate lower
than sum of
individual
flow rates
(BPMA)
37
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
4. Eliminating Flow Control Valve
ElectricalEquipment/
Pumps
• Closing/opening discharge valve (“throttling”)
to reduce flow
• Head increases:
does not reduce
power use
• Vibration and
corrosion: high
maintenance
costs and reduced
pump lifetime
(BPMA)
38
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
5. Eliminating By-pass Control
ElectricalEquipment/
Pumps
• Pump discharge divided into two
flows
• One pipeline delivers fluid to destination
• Second pipeline returns fluid to the source
• Energy wastage because part of fluid
pumped around for no reason
39
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
6. Start / Stop Control of Pump
ElectricalEquipment/
Pumps
• Stop the pump when not needed
• Example:
• Filling of storage tank
• Controllers in tank to start/stop
• Suitable if not done too frequently
• Method to lower the maximum
demand (pumping at non-peak hours)
40
©© UNEP 2006UNEP 2006
Energy Efficiency OpportunitiesEnergy Efficiency Opportunities
7. Impeller Trimming
ElectricalEquipment/
Pumps
• Changing diameter: change in
velocity
• Considerations
• Cannot be used with varying flows
• No trimming >25% of impeller size
• Impeller trimming same on all sides
• Changing impeller is better option but more
expensive and not always possible
41
Pumps & PumpingPumps & Pumping
SystemsSystems
THANK YOUTHANK YOU
FOR YOUR ATTENTIONFOR YOUR ATTENTION


Mais conteúdo relacionado

Mais procurados

Selection of pump
Selection of pumpSelection of pump
Selection of pumpsofrani
 
AN INTRODUCTION TO PUMPING EQUIPMENT
AN INTRODUCTION TO PUMPING EQUIPMENT AN INTRODUCTION TO PUMPING EQUIPMENT
AN INTRODUCTION TO PUMPING EQUIPMENT Aviation Trial Corp.
 
Chapter pumps and pumping systems
Chapter pumps and pumping systemsChapter pumps and pumping systems
Chapter pumps and pumping systemsSyahenzlys
 
Hydro Power Plant Auxaleries
Hydro Power Plant AuxaleriesHydro Power Plant Auxaleries
Hydro Power Plant AuxaleriesMahajan Saurabh
 
Draft tubes merits and demerits
Draft tubes merits and demeritsDraft tubes merits and demerits
Draft tubes merits and demeritsPraveen Kumar
 
pumps and centrifugal pump and their classifications
pumps and centrifugal pump and their classificationspumps and centrifugal pump and their classifications
pumps and centrifugal pump and their classificationsTalha Hussain
 
pumps and its types-ppt
pumps and its types-pptpumps and its types-ppt
pumps and its types-pptDharmas India
 
Positive Displacement Pumps - Basic Principle
Positive Displacement Pumps - Basic PrinciplePositive Displacement Pumps - Basic Principle
Positive Displacement Pumps - Basic PrincipleSahyog Shishodia
 
Submersible pump ppt
Submersible pump pptSubmersible pump ppt
Submersible pump pptS SHANKAR RAO
 
Calculation Of Pump Head
Calculation Of Pump HeadCalculation Of Pump Head
Calculation Of Pump HeadHashim Khan
 

Mais procurados (20)

Introduction of pump
Introduction of pumpIntroduction of pump
Introduction of pump
 
Pumps and types of pumps
Pumps and types of pumpsPumps and types of pumps
Pumps and types of pumps
 
Selection of pump
Selection of pumpSelection of pump
Selection of pump
 
centrifugal pump ppt
centrifugal pump pptcentrifugal pump ppt
centrifugal pump ppt
 
Pumps presentation
Pumps presentationPumps presentation
Pumps presentation
 
AN INTRODUCTION TO PUMPING EQUIPMENT
AN INTRODUCTION TO PUMPING EQUIPMENT AN INTRODUCTION TO PUMPING EQUIPMENT
AN INTRODUCTION TO PUMPING EQUIPMENT
 
Chapter pumps and pumping systems
Chapter pumps and pumping systemsChapter pumps and pumping systems
Chapter pumps and pumping systems
 
Hydro Power Plant Auxaleries
Hydro Power Plant AuxaleriesHydro Power Plant Auxaleries
Hydro Power Plant Auxaleries
 
Submersible pump
Submersible pumpSubmersible pump
Submersible pump
 
Pumps
PumpsPumps
Pumps
 
Pumps
PumpsPumps
Pumps
 
Draft tubes merits and demerits
Draft tubes merits and demeritsDraft tubes merits and demerits
Draft tubes merits and demerits
 
pumps and centrifugal pump and their classifications
pumps and centrifugal pump and their classificationspumps and centrifugal pump and their classifications
pumps and centrifugal pump and their classifications
 
Centrifugal Pumps
Centrifugal PumpsCentrifugal Pumps
Centrifugal Pumps
 
pumps and its types-ppt
pumps and its types-pptpumps and its types-ppt
pumps and its types-ppt
 
Positive Displacement Pumps - Basic Principle
Positive Displacement Pumps - Basic PrinciplePositive Displacement Pumps - Basic Principle
Positive Displacement Pumps - Basic Principle
 
Submersible pump ppt
Submersible pump pptSubmersible pump ppt
Submersible pump ppt
 
Types of turbine
Types of turbineTypes of turbine
Types of turbine
 
Calculation Of Pump Head
Calculation Of Pump HeadCalculation Of Pump Head
Calculation Of Pump Head
 
Water pump
Water pumpWater pump
Water pump
 

Destaque

Pumps and types of pumps in detail
Pumps and types of pumps in detailPumps and types of pumps in detail
Pumps and types of pumps in detailFARRUKH SHEHZAD
 
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01Jose Acuna
 
Pumps for Process Industries
Pumps for Process IndustriesPumps for Process Industries
Pumps for Process IndustriesRanjeet Kumar
 

Destaque (6)

PUMPS
 PUMPS PUMPS
PUMPS
 
Pumps and types of pumps in detail
Pumps and types of pumps in detailPumps and types of pumps in detail
Pumps and types of pumps in detail
 
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01
Centrifugalpumpsizingselectionandd lesignpractices 12758726575297-phpapp01
 
Pumps Senatorlibya
Pumps SenatorlibyaPumps Senatorlibya
Pumps Senatorlibya
 
Pumps for Process Industries
Pumps for Process IndustriesPumps for Process Industries
Pumps for Process Industries
 
Pump total basics
Pump total basicsPump total basics
Pump total basics
 

Semelhante a Pumps & pumping systems

Pumps and pumping systems
Pumps and pumping systemsPumps and pumping systems
Pumps and pumping systemsYOGESH AHIRE
 
3: Energy Management In Water Supply Systems - Pumping Operations
3: Energy Management In Water Supply Systems - Pumping Operations3: Energy Management In Water Supply Systems - Pumping Operations
3: Energy Management In Water Supply Systems - Pumping OperationsAlliance To Save Energy
 
hydraulics introduction
hydraulics introductionhydraulics introduction
hydraulics introductionillpa
 
Lesson 14 hydraulics
Lesson 14   hydraulicsLesson 14   hydraulics
Lesson 14 hydraulicsKishor Patil
 
Design of Hydraulic and Pneumatic Systems Digital Material.pdf
Design of Hydraulic and Pneumatic Systems Digital Material.pdfDesign of Hydraulic and Pneumatic Systems Digital Material.pdf
Design of Hydraulic and Pneumatic Systems Digital Material.pdfSriramadasusreenu
 
energy efficient operation of Fans and blowers
energy efficient operation of Fans and blowersenergy efficient operation of Fans and blowers
energy efficient operation of Fans and blowersShanid Pazhamkavil
 
Minimizing power requirment for pumps in dairy industry
Minimizing power requirment for pumps in dairy industryMinimizing power requirment for pumps in dairy industry
Minimizing power requirment for pumps in dairy industryAdarsh M.kalla
 
MCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxMCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxDavidPeaceAchebe
 
fansandblowers-110720000533-phpapp01.ppt
fansandblowers-110720000533-phpapp01.pptfansandblowers-110720000533-phpapp01.ppt
fansandblowers-110720000533-phpapp01.pptRutaPawar3
 
57573011830118 fan efficiency calculator.ppt
57573011830118 fan efficiency calculator.ppt57573011830118 fan efficiency calculator.ppt
57573011830118 fan efficiency calculator.pptDkKumar19
 
Hydraulics and Pneumatics - Hydraulic Pumps
Hydraulics and Pneumatics - Hydraulic Pumps Hydraulics and Pneumatics - Hydraulic Pumps
Hydraulics and Pneumatics - Hydraulic Pumps S. Sathishkumar
 
An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems Leonardo ENERGY
 
Centrifugal pump lecture 1
Centrifugal pump lecture 1Centrifugal pump lecture 1
Centrifugal pump lecture 1Rahul Singhal
 
Rceprocating pump
Rceprocating pumpRceprocating pump
Rceprocating pumpFahad jee
 
Optimum overhaul of pumps 2014
Optimum overhaul of pumps 2014Optimum overhaul of pumps 2014
Optimum overhaul of pumps 2014Ray Beebe
 

Semelhante a Pumps & pumping systems (20)

Pump and pumping system
Pump and pumping systemPump and pumping system
Pump and pumping system
 
Pumps and pumping systems
Pumps and pumping systemsPumps and pumping systems
Pumps and pumping systems
 
3: Energy Management In Water Supply Systems - Pumping Operations
3: Energy Management In Water Supply Systems - Pumping Operations3: Energy Management In Water Supply Systems - Pumping Operations
3: Energy Management In Water Supply Systems - Pumping Operations
 
hydraulics introduction
hydraulics introductionhydraulics introduction
hydraulics introduction
 
Lesson 14 hydraulics
Lesson 14   hydraulicsLesson 14   hydraulics
Lesson 14 hydraulics
 
Design of Hydraulic and Pneumatic Systems Digital Material.pdf
Design of Hydraulic and Pneumatic Systems Digital Material.pdfDesign of Hydraulic and Pneumatic Systems Digital Material.pdf
Design of Hydraulic and Pneumatic Systems Digital Material.pdf
 
energy efficient operation of Fans and blowers
energy efficient operation of Fans and blowersenergy efficient operation of Fans and blowers
energy efficient operation of Fans and blowers
 
Minimizing power requirment for pumps in dairy industry
Minimizing power requirment for pumps in dairy industryMinimizing power requirment for pumps in dairy industry
Minimizing power requirment for pumps in dairy industry
 
Pumps.pptx
Pumps.pptxPumps.pptx
Pumps.pptx
 
Electrical motors (1)
Electrical motors (1)Electrical motors (1)
Electrical motors (1)
 
MCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptxMCE416 Fluid power system lecture note Lecture note.pptx
MCE416 Fluid power system lecture note Lecture note.pptx
 
fansandblowers-110720000533-phpapp01.ppt
fansandblowers-110720000533-phpapp01.pptfansandblowers-110720000533-phpapp01.ppt
fansandblowers-110720000533-phpapp01.ppt
 
57573011830118 fan efficiency calculator.ppt
57573011830118 fan efficiency calculator.ppt57573011830118 fan efficiency calculator.ppt
57573011830118 fan efficiency calculator.ppt
 
Hydraulics and Pneumatics - Hydraulic Pumps
Hydraulics and Pneumatics - Hydraulic Pumps Hydraulics and Pneumatics - Hydraulic Pumps
Hydraulics and Pneumatics - Hydraulic Pumps
 
An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems An introduction to Energy Saving Opportunities in Pumping Systems
An introduction to Energy Saving Opportunities in Pumping Systems
 
Centrifugal pump lecture 1
Centrifugal pump lecture 1Centrifugal pump lecture 1
Centrifugal pump lecture 1
 
Electrical motors 4to medio.ppt
Electrical motors 4to medio.pptElectrical motors 4to medio.ppt
Electrical motors 4to medio.ppt
 
Rceprocating pump
Rceprocating pumpRceprocating pump
Rceprocating pump
 
Optimum overhaul of pumps 2014
Optimum overhaul of pumps 2014Optimum overhaul of pumps 2014
Optimum overhaul of pumps 2014
 
Mine mechanisation 1
Mine mechanisation 1Mine mechanisation 1
Mine mechanisation 1
 

Mais de Sudhir Reddy

Weld joint geometry and welding symbols
Weld joint geometry and welding symbolsWeld joint geometry and welding symbols
Weld joint geometry and welding symbolsSudhir Reddy
 
Seminor on air motors
Seminor on air motorsSeminor on air motors
Seminor on air motorsSudhir Reddy
 
Programming logic controllers (plc)
Programming  logic controllers (plc)Programming  logic controllers (plc)
Programming logic controllers (plc)Sudhir Reddy
 
Manipulator kinematics
Manipulator kinematicsManipulator kinematics
Manipulator kinematicsSudhir Reddy
 
Just in-time systems
Just in-time systemsJust in-time systems
Just in-time systemsSudhir Reddy
 
Introduction to microprocessor
Introduction to microprocessorIntroduction to microprocessor
Introduction to microprocessorSudhir Reddy
 
Flexible manufacturing systems
Flexible manufacturing systemsFlexible manufacturing systems
Flexible manufacturing systemsSudhir Reddy
 
Cadcam considerations about fms
Cadcam considerations about fmsCadcam considerations about fms
Cadcam considerations about fmsSudhir Reddy
 
Assembly systems & line balance
Assembly systems & line balanceAssembly systems & line balance
Assembly systems & line balanceSudhir Reddy
 
Application of robot’s
Application of robot’sApplication of robot’s
Application of robot’sSudhir Reddy
 

Mais de Sudhir Reddy (15)

Weld joint geometry and welding symbols
Weld joint geometry and welding symbolsWeld joint geometry and welding symbols
Weld joint geometry and welding symbols
 
Seminor on air motors
Seminor on air motorsSeminor on air motors
Seminor on air motors
 
Programming logic controllers (plc)
Programming  logic controllers (plc)Programming  logic controllers (plc)
Programming logic controllers (plc)
 
Manipulator kinematics
Manipulator kinematicsManipulator kinematics
Manipulator kinematics
 
L20
L20L20
L20
 
Just in-time systems
Just in-time systemsJust in-time systems
Just in-time systems
 
Introduction to microprocessor
Introduction to microprocessorIntroduction to microprocessor
Introduction to microprocessor
 
Gear pump
Gear pumpGear pump
Gear pump
 
Flexible manufacturing systems
Flexible manufacturing systemsFlexible manufacturing systems
Flexible manufacturing systems
 
Cadcam considerations about fms
Cadcam considerations about fmsCadcam considerations about fms
Cadcam considerations about fms
 
Assembly systems & line balance
Assembly systems & line balanceAssembly systems & line balance
Assembly systems & line balance
 
Application of robot’s
Application of robot’sApplication of robot’s
Application of robot’s
 
Accumulators
AccumulatorsAccumulators
Accumulators
 
10 mech seminars
10 mech seminars10 mech seminars
10 mech seminars
 
Nc programming
Nc programmingNc programming
Nc programming
 

Último

Prescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxPrescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxraviapr7
 
Ultra structure and life cycle of Plasmodium.pptx
Ultra structure and life cycle of Plasmodium.pptxUltra structure and life cycle of Plasmodium.pptx
Ultra structure and life cycle of Plasmodium.pptxDr. Asif Anas
 
How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17Celine George
 
Benefits & Challenges of Inclusive Education
Benefits & Challenges of Inclusive EducationBenefits & Challenges of Inclusive Education
Benefits & Challenges of Inclusive EducationMJDuyan
 
Human-AI Co-Creation of Worked Examples for Programming Classes
Human-AI Co-Creation of Worked Examples for Programming ClassesHuman-AI Co-Creation of Worked Examples for Programming Classes
Human-AI Co-Creation of Worked Examples for Programming ClassesMohammad Hassany
 
What is the Future of QuickBooks DeskTop?
What is the Future of QuickBooks DeskTop?What is the Future of QuickBooks DeskTop?
What is the Future of QuickBooks DeskTop?TechSoup
 
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdf
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdfMaximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdf
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdfTechSoup
 
3.21.24 The Origins of Black Power.pptx
3.21.24  The Origins of Black Power.pptx3.21.24  The Origins of Black Power.pptx
3.21.24 The Origins of Black Power.pptxmary850239
 
General views of Histopathology and step
General views of Histopathology and stepGeneral views of Histopathology and step
General views of Histopathology and stepobaje godwin sunday
 
Quality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICEQuality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICESayali Powar
 
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptxClinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptxraviapr7
 
How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17Celine George
 
Patient Counselling. Definition of patient counseling; steps involved in pati...
Patient Counselling. Definition of patient counseling; steps involved in pati...Patient Counselling. Definition of patient counseling; steps involved in pati...
Patient Counselling. Definition of patient counseling; steps involved in pati...raviapr7
 
5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...CaraSkikne1
 
Practical Research 1 Lesson 9 Scope and delimitation.pptx
Practical Research 1 Lesson 9 Scope and delimitation.pptxPractical Research 1 Lesson 9 Scope and delimitation.pptx
Practical Research 1 Lesson 9 Scope and delimitation.pptxKatherine Villaluna
 
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptxSandy Millin
 
The Singapore Teaching Practice document
The Singapore Teaching Practice documentThe Singapore Teaching Practice document
The Singapore Teaching Practice documentXsasf Sfdfasd
 
Presentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphPresentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphNetziValdelomar1
 
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxPractical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxKatherine Villaluna
 

Último (20)

Prescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxPrescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptx
 
Ultra structure and life cycle of Plasmodium.pptx
Ultra structure and life cycle of Plasmodium.pptxUltra structure and life cycle of Plasmodium.pptx
Ultra structure and life cycle of Plasmodium.pptx
 
How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17
 
Benefits & Challenges of Inclusive Education
Benefits & Challenges of Inclusive EducationBenefits & Challenges of Inclusive Education
Benefits & Challenges of Inclusive Education
 
Human-AI Co-Creation of Worked Examples for Programming Classes
Human-AI Co-Creation of Worked Examples for Programming ClassesHuman-AI Co-Creation of Worked Examples for Programming Classes
Human-AI Co-Creation of Worked Examples for Programming Classes
 
What is the Future of QuickBooks DeskTop?
What is the Future of QuickBooks DeskTop?What is the Future of QuickBooks DeskTop?
What is the Future of QuickBooks DeskTop?
 
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdf
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdfMaximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdf
Maximizing Impact_ Nonprofit Website Planning, Budgeting, and Design.pdf
 
3.21.24 The Origins of Black Power.pptx
3.21.24  The Origins of Black Power.pptx3.21.24  The Origins of Black Power.pptx
3.21.24 The Origins of Black Power.pptx
 
General views of Histopathology and step
General views of Histopathology and stepGeneral views of Histopathology and step
General views of Histopathology and step
 
Quality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICEQuality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICE
 
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptxClinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
 
How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17
 
Patient Counselling. Definition of patient counseling; steps involved in pati...
Patient Counselling. Definition of patient counseling; steps involved in pati...Patient Counselling. Definition of patient counseling; steps involved in pati...
Patient Counselling. Definition of patient counseling; steps involved in pati...
 
5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...
 
Practical Research 1 Lesson 9 Scope and delimitation.pptx
Practical Research 1 Lesson 9 Scope and delimitation.pptxPractical Research 1 Lesson 9 Scope and delimitation.pptx
Practical Research 1 Lesson 9 Scope and delimitation.pptx
 
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
 
The Singapore Teaching Practice document
The Singapore Teaching Practice documentThe Singapore Teaching Practice document
The Singapore Teaching Practice document
 
Presentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphPresentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a Paragraph
 
Prelims of Kant get Marx 2.0: a general politics quiz
Prelims of Kant get Marx 2.0: a general politics quizPrelims of Kant get Marx 2.0: a general politics quiz
Prelims of Kant get Marx 2.0: a general politics quiz
 
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxPractical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
 

Pumps & pumping systems

  • 1. 1 Pumps & PumpingPumps & Pumping SystemsSystems By SUDHIR REDDY S.V.R M.TECH(CAD/CAM)
  • 2. 2 ©© UNEP 2006UNEP 2006 Training Agenda: PumpsTraining Agenda: Pumps Introduction Type of pumps Assessment of pumps Energy efficiency opportunities ElectricalEquipment/ Pumps
  • 3. 3 ©© UNEP 2006UNEP 2006 IntroductionIntroduction • 20% of world’s electrical energy demand • 25-50% of energy usage in some industries • Used for • Domestic, commercial, industrial and agricultural services • Municipal water and wastewater services What are Pumping Systems ElectricalEquipment/ Pumps
  • 4. 4 ©© UNEP 2006UNEP 2006 IntroductionIntroduction Objective of pumping system What are Pumping Systems ElectricalEquipment/ Pumps (US DOE, 2001) • Transfer liquid from source to destination • Circulate liquid around a system
  • 5. 5 ©© UNEP 2006UNEP 2006 IntroductionIntroduction • Main pump components • Pumps • Prime movers: electric motors, diesel engines, air system • Piping to carry fluid • Valves to control flow in system • Other fittings, control, instrumentation • End-use equipment • Heat exchangers, tanks, hydraulic machines What are Pumping Systems ElectricalEquipment/ Pumps
  • 6. 6 ©© UNEP 2006UNEP 2006 IntroductionIntroduction • Head • Resistance of the system • Two types: static and friction • Static head • Difference in height between source and destination • Independent of flow Pumping System Characteristics ElectricalEquipment/ Pumps destination source Stati c head Static head Flow
  • 7. 7 ©© UNEP 2006UNEP 2006 IntroductionIntroduction • Static head consists of • Static suction head (hS): lifting liquid relative to pump center line • Static discharge head (hD) vertical distance between centerline and liquid surface in destination tank • Static head at certain pressure Pumping System Characteristics ElectricalEquipment/ Pumps Head (in feet) = Pressure (psi) X 2.31 Specific gravity
  • 8. 8 ©© UNEP 2006UNEP 2006 IntroductionIntroduction • Friction head • Resistance to flow in pipe and fittings • Depends on size, pipes, pipe fittings, flow rate, nature of liquid • Proportional to square of flow rate • Closed loop system only has friction head (no static head) Pumping System Characteristics ElectricalEquipment/ Pumps Friction head Flow
  • 9. 9 ©© UNEP 2006UNEP 2006 IntroductionIntroduction In most cases: Total head = Static head + friction head Pumping System Characteristics ElectricalEquipment/ Pumps System head Flow Static head Friction head System curve System head Flow Static head Friction head System curve
  • 10. 10 ©© UNEP 2006UNEP 2006 Training Agenda: PumpsTraining Agenda: Pumps Introduction Type of pumps Assessment of pumps Energy efficiency opportunities ElectricalEquipment/ Pumps
  • 11. 11 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Classified by operating principle Pump Classification ElectricalEquipment/ Pumps Dynamic Positive Displacement Centrifugal Special effect Rotary Reciprocating Internal gear External gear Lobe Slide vane Others (e.g. Impulse, Buoyancy) Pumps Dynamic Positive Displacement Centrifugal Special effect Rotary Reciprocating Internal gear External gear Lobe Slide vane Others (e.g. Impulse, Buoyancy) Pumps
  • 12. 12 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Positive Displacement Pumps ElectricalEquipment/ Pumps • For each pump revolution • Fixed amount of liquid taken from one end • Positively discharged at other end • If pipe blocked • Pressure rises • Can damage pump • Used for pumping fluids other than water
  • 13. 13 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Positive Displacement Pumps ElectricalEquipment/ Pumps • Reciprocating pump • Displacement by reciprocation of piston plunger • Used only for viscous fluids and oil wells • Rotary pump • Displacement by rotary action of gear, cam or vanes • Several sub-types • Used for special services in industry
  • 14. 14 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Dynamic pumps ElectricalEquipment/ Pumps • Mode of operation • Rotating impeller converts kinetic energy into pressure or velocity to pump the fluid • Two types • Centrifugal pumps: pumping water in industry – 75% of pumps installed • Special effect pumps: specialized conditions
  • 15. 15 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Centrifugal Pumps ElectricalEquipment/ Pumps How do they work? (Sahdev M) • Liquid forced into impeller • Vanes pass kinetic energy to liquid: liquid rotates and leaves impeller • Volute casing converts kinetic energy into pressure energy
  • 16. 16 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Centrifugal Pumps ElectricalEquipment/ Pumps Rotating and stationary components (Sahdev)
  • 17. 17 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Centrifugal Pumps ElectricalEquipment/ Pumps Impeller Sahdev) • Main rotating part that provides centrifugal acceleration to the fluid • Number of impellers = number of pump stages • Impeller classification: direction of flow, suction type and shape/mechanical construction Shaft • Transfers torque from motor to impeller during pump start up and operation
  • 18. 18 ©© UNEP 2006UNEP 2006 Type of PumpsType of Pumps Centrifugal Pumps ElectricalEquipment/ Pumps Casings Volute Casing (Sahdev) • Functions • Enclose impeller as “pressure vessel” • Support and bearing for shaft and impeller • Volute case • Impellers inside casings • Balances hydraulic pressure on pump shaft • Circular casing • Vanes surrounds impeller • Used for multi-stage pumps
  • 22. 22 Gear Pump BalancedGear Pump Balanced
  • 25. 25 Bent Axis Piston PumpBent Axis Piston Pump
  • 26. 26 Swash Plate Piston PumpSwash Plate Piston Pump
  • 27. 27 ©© UNEP 2006UNEP 2006 Training Agenda: PumpsTraining Agenda: Pumps Introduction Type of pumps Assessment of pumps Energy efficiency opportunities ElectricalEquipment/ Pumps
  • 28. 28 Assessment of pumpsAssessment of pumps • Pump shaft power (Ps) is actual horsepower delivered to the pump shaft • Pump output/Hydraulic/Water horsepower (Hp) is the liquid horsepower delivered by the pump How to Calculate Pump Performance ElectricalEquipment/ Pumps Hydraulic power (Hp): Hp = Q (m3/s) x Total head, hd - hs (m) x ρ (kg/m3) x g (m/s2) / 1000 Pump shaft power (Ps): Ps = Hydraulic power Hp / pump efficiency ηPump Pump Efficiency (ηPump): ηPump = Hydraulic Power / Pump Shaft Power ©© UNEP 2006UNEP 2006 hd - discharge head hs – suction head, ρ - density of the fluid g – acceleration due to gravity
  • 29. 29 ©© UNEP 2006UNEP 2006 Assessment of pumpsAssessment of pumps • Absence of pump specification data to assess pump performance • Difficulties in flow measurement and flows are often estimated • Improper calibration of pressure gauges & measuring instruments • Calibration not always carried out • Correction factors used Difficulties in Pump Assessment ElectricalEquipment/ Pumps
  • 30. 30 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 1. Selecting the right pump 2. Controlling the flow rate by speed variation 3. Pumps in parallel to meet varying demand 4. Eliminating flow control valve 5. Eliminating by-pass control 6. Start/stop control of pump 7. Impeller trimming ElectricalEquipment/ Pumps
  • 31. 31 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 1. Selecting the Right Pump ElectricalEquipment/ Pumps Pump performance curve for centrifugal pump BEE India, 2004
  • 32. 32 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 1. Selecting the Right Pump ElectricalEquipment/ Pumps • Oversized pump • Requires flow control (throttle valve or by- pass line) • Provides additional head • System curve shifts to left • Pump efficiency is reduced • Solutions if pump already purchased • VSDs or two-speed drives • Lower RPM • Smaller or trimmed impeller
  • 33. 33 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 2. Controlling Flow: speed variation ElectricalEquipment/ Pumps Explaining the effect of speed • Affinity laws: relation speed N and • Flow rate Q α N • Head H α N2 • Power P α N3 • Small speed reduction (e.g. ½) = large power reduction (e.g. 1/8)
  • 34. 34 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency OpportunitiesElectricalEquipment/ Pumps Variable Speed Drives (VSD) • Speed adjustment over continuous range • Power consumption also reduced! • Two types • Mechanical: hydraulic clutches, fluid couplings, adjustable belts and pulleys • Electrical: eddy current clutches, wound-rotor motor controllers, Variable Frequency Drives (VFDs) 2. Controlling Flow: speed variation
  • 35. 35 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency OpportunitiesElectricalEquipment/ Pumps Benefits of VSDs • Energy savings (not just reduced flow!) • Improved process control • Improved system reliability • Reduced capital and maintenance costs • Soft starter capability 2. Controlling Flow: speed variation
  • 36. 36 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 3. Parallel Pumps for Varying Demand ElectricalEquipment/ Pumps • Multiple pumps: some turned off during low demand • Used when static head is >50% of total head • System curve does not change • Flow rate lower than sum of individual flow rates (BPMA)
  • 37. 37 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 4. Eliminating Flow Control Valve ElectricalEquipment/ Pumps • Closing/opening discharge valve (“throttling”) to reduce flow • Head increases: does not reduce power use • Vibration and corrosion: high maintenance costs and reduced pump lifetime (BPMA)
  • 38. 38 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 5. Eliminating By-pass Control ElectricalEquipment/ Pumps • Pump discharge divided into two flows • One pipeline delivers fluid to destination • Second pipeline returns fluid to the source • Energy wastage because part of fluid pumped around for no reason
  • 39. 39 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 6. Start / Stop Control of Pump ElectricalEquipment/ Pumps • Stop the pump when not needed • Example: • Filling of storage tank • Controllers in tank to start/stop • Suitable if not done too frequently • Method to lower the maximum demand (pumping at non-peak hours)
  • 40. 40 ©© UNEP 2006UNEP 2006 Energy Efficiency OpportunitiesEnergy Efficiency Opportunities 7. Impeller Trimming ElectricalEquipment/ Pumps • Changing diameter: change in velocity • Considerations • Cannot be used with varying flows • No trimming >25% of impeller size • Impeller trimming same on all sides • Changing impeller is better option but more expensive and not always possible
  • 41. 41 Pumps & PumpingPumps & Pumping SystemsSystems THANK YOUTHANK YOU FOR YOUR ATTENTIONFOR YOUR ATTENTION 

Notas do Editor

  1. TO THE TRAINER This PowerPoint presentation can be used to train people about the basics of pumps and pumping systems. The information on the slides is the minimum information that should be explained. The trainer notes for each slide provide more detailed information, but it is up to the trainer to decide if and how much of this information is presented also. Additional materials that can be used for the training session are available on www.energyefficiencyasia.org under “Energy Equipment” and include: Textbook chapter on this energy equipment that forms the basis of this PowerPoint presentation but has more detailed information Quiz – ten multiple choice questions that trainees can answer after the training session Workshop exercise – a practical calculation related to this equipment Option checklist – a list of the most important options to improve energy efficiency of this equipment Company case studies – participants of past courses have given the feedback that they would like to hear about options implemented at companies for each energy equipment. More than 200 examples are available from 44 companies in the cement, steel, chemicals, ceramics and pulp & paper sectors
  2. Pumping systems account for nearly 20% of the world’s electrical energy demand. Furthermore, they range between 25-50% of the energy usage in certain industrial plant operations. The use of pumping systems is widespread. They provide domestic, commercial and agricultural services. In addition, they provide municipal water and wastewater services, and industrial services for food processing, chemical, petrochemical, pharmaceutical, and mechanical industries.
  3. Pumps have two main purposes: Transfer of liquid from one place to another place (e.g. water from an underground aquifer into a water storage tank) Circulate liquid around a system (e.g. cooling water or lubricants through machines and equipment)
  4. The main components of a pumping system are: Pumps (different types of pumps are explained in section 2) Prime movers: electric motors, diesel engines or air system Piping, used to carry the fluid Valves, used to control the flow in the system Other fittings, controls and instrumentation End-use equipment, which have different requirements (e.g. pressure, flow) and therefore determine the pumping system components and configuration. Examples include heat exchangers, tanks and hydraulic machines
  5. Pressure is needed to pump the liquid through the system at a certain rate. This pressure has to be high enough to overcome the resistance of the system, which is also called “head”. The total head is the sum of static head and friction head. Static head Static head is the difference in height between the source and destination of the pumped liquid (see top figure) Static head is independent of the flow (see bottom figure)
  6. Static head consists of: Static suction head (hS): resulting from lifting the liquid relative to the pump center line. The hS is positive if the liquid level is above pump centerline, and negative if the liquid level is below pump centerline (also called “suction lift) Static discharge head (hd): the vertical distance between the pump centerline and the surface of the liquid in the destination tank The static head at a certain pressure depends on the weight of the liquid and can be calculated with this equation: Head (in feet) = Pressure (psi) X 2.31 Specific gravity
  7. Friction head: This is the loss needed to overcome that is caused by the resistance to flow in the pipe and fittings. It is dependent on size, condition and type of pipe, number and type of pipe fittings, flow rate, and nature of the liquid. The friction head is proportional to the square of the flow rate as shown in the figure. A closed loop circulating system only exhibits friction head (i.e. not static head).
  8. In most cases the total head of a system is a combination of static head and friction head as shown in the figures Left figure is system with a high static head (i.e. the destination reservoir is much higher than the source) Right figure is system with a low static head (i.e. the destination reservoir is not much higher than the source)
  9. This section include various types of pumps. Pumps come in a variety of sizes for a wide range of applications. They can be classified according to their basic operating principle as dynamic or displacement pumps. Dynamic pumps can be sub-classified as centrifugal and special effect pumps. Displacement pumps can be sub-classified as rotary or reciprocating pumps. In principle, any liquid can be handled by any of the pump designs. Where different pump designs could be used, the centrifugal pump is generally the most economical followed by rotary and reciprocating pumps. Although positive displacement pumps are generally more efficient than centrifugal pumps, the benefit of higher efficiency tends to be offset by increased maintenance costs.
  10. Pumps come in a variety of sizes for a wide range of applications. They can be classified according to their basic operating principle as dynamic or positive displacement pumps In principle, any liquid can be handled by any of the pump designs. Centrifugal pump is generally the most economical but less efficient. Positive displacement pumps are generally more efficient than centrifugal pumps, but higher maintenance costs.
  11. Positive displacement pumps are distinguished by the way they operate: liquid is taken from one end and positively discharged at the other end for every revolution. In all positive displacement type pumps, a fixed quantity of liquid is pumped after each revolution. So if the delivery pipe is blocked, the pressure rises to a very high value, which can damage the pump. Positive displacement pumps are widely used for pumping fluids other than water, mostly viscous fluids.
  12. Positive displacement pumps are further classified based upon the mode of displacement: Reciprocating pump if the displacement is by reciprocation of a piston plunger. Reciprocating pumps are used only for pumping viscous liquids and oil wells. Rotary pumps if the displacement is by rotary action of a gear, cam or vanes in a chamber of diaphragm in a fixed casing. Rotary pumps are further classified such as internal gear, external gear, lobe and slide vane etc. These pumps are used for special services with particular conditions existing in industrial sites.
  13. Dynamic pumps are also characterized by their mode of operation: a rotating impeller converts kinetic energy into pressure or velocity that is needed to pump the fluid. There are two types of dynamic pumps: Centrifugal pumps are the most common pumps used for pumping water in industrial applications. Typically, more than 75% of the pumps installed in an industry are centrifugal pumps. For this reason, this pump is further described on the next slides. Special effect pumps are particularly used for specialized conditions at an industrial site
  14. A centrifugal pump is one of the simplest pieces of equipment in any process plant. The figure shows how this type of pump operates: Liquid is forced into an impeller either by atmospheric pressure, or in case of a jet pump by artificial pressure. The vanes of impeller pass kinetic energy to the liquid, thereby causing the liquid to rotate. The liquid leaves the impeller at high velocity. The impeller is surrounded by a volute casing or in case of a turbine pump a stationary diffuser ring. The volute or stationary diffuser ring converts the kinetic energy into pressure energy.
  15. A centrifugal pump has two main components. First, a rotating component comprised of an impeller and a shaft (click once and circles will appear). And secondly, a stationary component comprised of a casing, casing cover, and bearings (click once and circles will appear).
  16. Impeller An impeller is a circular metallic disc with a built-in passage for the flow of fluid. Impellers are generally made of bronze, polycarbonate, cast iron or stainless steel, but other materials are also used. The number of impellers determines the number of stages of the pump. A single stage pump has one impeller and is best suited for low head (= pressure) Impellers can be classified on the basis of (which will determine their use): Major direction of flow from the rotation axis Suction type: single suction and double suction Shape or mechanical construction: Closed impellers have vanes enclosed by shrouds; Open and semi-open impellers; Vortex pump impellers. The figure shows an open type impeller and a closed type impeller Shaft The shaft transfers the torque from the motor to the impeller during the startup and operation of the pump.
  17. Casings have two functions The main function of casing is to enclose the impeller at suction and delivery ends and thereby form a pressure vessel. A second function of casing is to provide a supporting and bearing medium for the shaft and impeller. (Click once) There are two types of casings Volute casing (see figure) has impellers that are fitted inside the casings. One of the main purposes is to help balance the hydraulic pressure on the shaft of the pump. Circular casing has stationary diffusion vanes surrounding the impeller periphery that convert speed into pressure energy. These casings are mostly used for multi-stage pumps. The casings can be designed as solid casing (one fabricated piece) or split casing (two or more parts together)
  18. The work performed by a pump is a function of the total head and of the weight of the liquid pumped in a given time period. Pump shaft power (Ps) is the actual horsepower delivered to the pump shaft, and can be calculated as follows: Pump shaft power Ps = Hydraulic power hp / Pump efficiency ηpump or Pump efficiency η pump = Hydraulic power / Pump shaft power Pump output, water horsepower or hydraulic horsepower (hp) is the liquid horsepower delivered by the pump, and can be calculated as follows: Hydraulic power hp = Q (m3/s) x (hd - hs in m) x ρ (kg/m3) x g (m/s2) / 1000 Where: Q = flow rate hd = discharge head hs = suction head ρ = density of the fluid g = acceleration due to gravity
  19. In practice, it is more difficult to assess pump performance. Some important reasons are: Absence of pump specification data : Pump specification data (see Worksheet 1 in section 6) are required to assess the pump performance. Most companies do not keep original equipment manufacturer (OEM) documents that provide these data. In these cases, the percentage pump loading for a pump flow or head cannot be estimated satisfactorily. Difficulty in flow measurement : It is difficult to measure the actual flow. The methods are used to estimate the flow. In most cases the flow rate is calculated based on type of fluid, head and pipe size etc, but the calculated figure may not be accurate. Another method is to divide the tank volume by the time it takes for the pump to fill the tank. This method can, however, only be applied if one pump is in operation and if the discharge valve of the tank is closed. The most sophisticated, accurate and least time consuming way to measure the pump flow is by measurement with an ultrasonic flow meter. Improper calibration of pressure gauges and measuring instruments : Proper calibration of all pressure gauges at suction and discharge lines and other power measuring instruments is important to obtain accurate measurements. But calibration has not always been carried out. Sometimes correction factors are used when gauges and instruments are not properly calibrated. Both will lead to incorrect performance assessment of pumps.
  20. This section includes the factors affecting pump performance and areas of energy conservation . The main areas for energy conservation include: Selecting the right pump Controlling the flow rate by speed variation Pumps in parallel to meet varying demand Eliminating flow control valve Eliminating by-pass control Start/stop control of pump Impeller trimming
  21. This figure shows a typical vendor-supplied pump performance curves for a centrifugal pump where clear water is the pumping liquid. In selecting the pump, suppliers try to match the system curve supplied by the user with a pump curve that satisfies these needs as closely as possible. The operating point is where the system curve and pump performance curve intersect (as explained in the introduction) The Best Efficiency Point (BEP) is the pumping capacity at maximum impeller diameter, in other words, at which the efficiency of the pump is highest. All points to the right or left of the BEP have a lower efficiency.
  22. The BEP is affected when the selected pump is oversized. The reason is that the flow of oversized pumps must be controlled with different methods, such as a throttle valve or a by-pass line. These provide additional resistance by increasing the friction. As a result the system curve shifts to the left and intersects the pump curve at another point. The BEP is now also lower. In other words, the pump efficiency is reduced because the output flow is reduced but power consumption is not. Inefficiencies of oversized pumps can be overcome by, for example, the installation of VSDs, two-speed drives, lower rpm, smaller impeller or trimmed impeller
  23. A centrifugal pump’s rotating impeller generates head. The impeller’s peripheral velocity is directly related to shaft rotational speed. Therefore varying the rotational speed has a direct effect on the performance of the pump. The pump performance parameters (flow rate, head, power) will change with varying rotating speeds. To safely control a pump at different speeds it is therefore important to understand the relationships between the two. The equations that explain these relationships are known as the “Affinity Laws”: Flow rate (Q) is proportional to the rotating speed (N) Head (H) is proportional to the square of the rotating speed Power (P) is proportional to the cube of the rotating speed As can be seen from the above laws, doubling the rotating speed of the centrifugal pump will increase the power consumption by 8 times. Conversely a small reduction in speed will result in a very large reduction in power consumption. This forms the basis for energy conservation in centrifugal pumps with varying flow requirements.
  24. Controlling the pump speed is the most efficient way to control the flow, because when the pump’s speed is reduced, the power consumption is also reduced. The most commonly used method to reduce pump speed is Variable Speed Drive (VSD). VSDs allow pump speed adjustments over a continuous range, avoiding the need to jump from speed to speed as with multiple-speed pumps. VSDs control pump speeds use two types of systems: Mechanical VSDs include hydraulic clutches, fluid couplings, and adjustable belts and pulleys. Electrical VSDs include eddy current clutches, wound-rotor motor controllers, and variable frequency drives (VFDs). VFDs are the most popular and adjust the electrical frequency of the power supplied to a motor to change the motor’s rotational speed.
  25. The major advantages of VSD application in addition to energy saving are: Improved process control because VSDs can correct small variations in flow more quickly. Improved system reliability because wear of pumps, bearings and seals is reduced. Reduction of capital & maintenance cost because control valves, by-pass lines, and conventional starters are no longer needed. Soft starter capability: VSDs allow the motor the motor to have a lower startup current.
  26. Operating two or more pumps in parallel and turning some off when the demand is lower, can result in significant energy savings. Pumps providing different flow rates can be used. Parallel pumps are an option when the static head is more than fifty percent of the total head. (Click once) The figure shows the pump curve for a single pump, two pumps operating in parallel and three pumps operating in parallel. that the system curve normally does not change by running pumps in parallel. that flow rate is lower than the sum of the flow rates of the different pumps.
  27. Another method to control the flow by closing or opening the discharge valve (this is also known as “throttling” the valves). While this method reduces the flow, disadvantages are It does not reduce the power consumed, as the total head (static head) increases. The figure shows how the system curve moves upwards and to the left when a discharge valve is half closed. increases vibration and corrosion and thereby increases maintenance costs of pumps and potentially reduces their lifetimes VSDs are a better solution from an energy efficiency perspective.
  28. The flow can also be reduced by installing a by-pass control system, in which the discharge of the pump is divided into two flows going into two separate pipelines. One of the pipelines delivers the fluid to the delivery point, while the second pipeline returns the fluid to the source. In other words, part of the fluid is pumped around for no reason, and thus is an energy wastage. This option should therefore be avoided.
  29. A simple and reasonable energy efficient way to reduce the flow rate is by starting and stopping the pump, provided that this does not happen to frequently. An example where this option can be applied, is when a pump is used to fill a storage tank from which the fluid flows to the process at a steady rate. In this system, controllers are installed at the minimum and maximum level inside the tank to start and stop the pump. Some companies use this method also to avoid lower the maximum demand (i.e. by pumping at non-peak hours).
  30. Changing the impeller diameter gives a proportional change in the impeller’s peripheral velocity Changing the impeller diameter is an energy efficient way to control the pump flow rate. However, for this option, the following should be considered: This option cannot be used where varying flow patterns exist. The impeller should not be trimmed more than 25% of the original impeller size, otherwise it leads to vibration due to cavitation and therefore decrease the pump efficiency. The balance of the pump has to been maintained, i.e. the impeller trimming should be the same on all sides. Changing the impeller itself is a better option than trimming the impeller, but is also more expensive and sometimes the smaller impeller is too small. Figure 17 illustrates the effect of impeller diameter reduction on centrifugal pump performance.
  31. Hello.