Wasting too much time assembling carpet protection dispensers? Have a large job-site or home remodel to do? Tired of worrying about construction boots all over your new carpet but want that new bathroom?
This guide will take you through the ins-and-outs of assembling and then installing carpet protection with the Pro Tect Carpet dispense. Installing floor protection in a seamless way that keeps your home safe during construction or remodels is an art. While we'll leave the specific purchase to you its important to at least know what proper floor and surface protection installation looks like if you are a homeowner.
Original Source: https://www.pro-tect.com/product/pro-tect-carpet-protection-film/
Beginners Guide to TikTok for Search - Rachel Pearson - We are Tilt __ Bright...
How to Assembler Carpet Protection Dispensers
1.
2. Construction and remodeling projects are not
easy, but with the proper tools and know-how,
your next project can be a breeze.
Carpet protection dispensers are an important tool to help prepare the
jobsite and protect its flooring assets. While not required, dispensers
easily cut the installation time in half when compared to manual
installation by hand. They’re also quick to assemble and simple to use.
3. HERE ARE A FEW REASONS YOU MAY NEED A CARPET PROTECTION DISPENSER:
The surface area you need to protect
is very large
You need to get the job done quickly
You experience back, knee, hip, or
other joint problems from strained
manual labor
You expect to use the dispenser
frequently or on multiple projects
4. The first step is to determine the size you need for your rolls of film protection.
The dispenser pictured below fits 24”, 30”, and 36” rolls. There are also larger
dispensers available with 36”, 48”, and 60” rolls.
The dispenser comes with three
different poles to correspond with
the different sizes of film rolls.
SIZING
5. The main piece of the dispenser has three holes: 24”, 30”, and 36”.
ASSEMBLY
7. STEP 1
1 2
SLIDE THE END PIECE INTO THE MAIN PIECE
Take the end piece and slide it into the
main piece by pushing the pin down.
When you reach the correctly sized hole
for your film roll, release the pin to lock
the pieces in place.
8. 1
REPEAT WITH THE OTHER END PIECE ON THE OPPOSITE SIDE
Take the other end piece and slide it into the
main piece on the opposite side by pushing
the pin down. Note: Do not adjust to the exact size
of the roll until the roll is in place.
Leave room to attach the roll in the
next few steps.
STEP 2
!
9. 1
ATTACH ONE END OF THE POLE
Attach one end of the pole in between the end
pieces by placing the pole end over the wheel.
STEP 3
10. 1 2
PUT THE FILM ROLL INTO PLACE
Stand the dispenser up on one end so it is vertical.
This will make it easier to add the film roll.
Next, put the film roll into place opposite
the pole.
STEP 4
Remember: Make sure the sticky side of the film is up and the edge is pointing the way you want to go.!
11. LOCK THE POLE AND FILM ROLL INTO PLACESTEP 5
1 2
Push the pin in to release the end piece and slide
it down to the appropriate size. Position the pole
and film roll over the wheels and push into place.
Reattach the end piece by snapping the pin into
the hole. This will secure the pole, film roll, and
main pieces of the device into place.
12. 1
ATTACH THE HANDLE TO THE DISPENSER
Attach the handle to the center of the dispenser.
CONGRATULATIONS! YOU’VE JUST ASSEMBLED YOUR CARPET PROTECTION DISPENSER.
NEXT WE’LL TAKE A QUICK LOOK AT HOW TO USE THE DISPENSER AND GET ROLLING!
STEP 6
14. STEP 1
1 2
GET THE FILM ROLL STARTED
Pull the film out and back over the pole. Position the dispenser so the film is beneath
the roller, sticky side down.
15. 1
ROLL THE FILM
Move the dispenser forward by pushing the
handle to roll out the film.
STEP 2
16. 1
CUT THE FILM
When you are finished with one section, you
can use the metal pole roller as a base to make
a straight, even cut.
You are then free to reposition the dispenser to
continue applying the film to the next section.
STEP 3
19. JUST REMEMBER TO FOLLOW THESE QUICK AND EASY STEPS:
TO ASSEMBLE
Slide the end piece into the main piece
Repeat with the other end piece on the opposite side
Attach one end of the pole
Put the film roll into place
Lock the pole and film roll into place
Attach the handle to the dispenser
20. JUST REMEMBER TO FOLLOW THESE QUICK AND EASY STEPS:
TO USE
Get the film roll started
Roll the film
Cut the film
Repeat as necessary
21. If you have any questions about assembling or using
your carpet protection dispenser, contact the experts
at Pro Tect today! No one knows how to “pro tect”
your floors better than Pro Tect.
THANKS