rive confidently knowing the most sophisticated anti-laser technology available is vigilantly detecting and protecting your vehicle. New Defuser EX & EX2 detects and deactivates the laser light signal transmitted by police laser guns by sending out a powerful return pulse signal at the same frequency. Simultaneously, you’re alerted to the targeting with audible and visual warnings, giving you the precious time you need to react and safely reduce your speed.
Defuser EX & EX2 provide total protection against police laser. All new internal electronics feature more powerful laser emitters, improved laser detection capabilities and updated programming against the latest police laser technology. And Defuser EX & EX2’s design is almost 50% smaller than any previous Laser Defuser, so the systems blend discreetly into any vehicle and are virtually unnoticeable.
More than Just Lines on a Map: Best Practices for U.S Bike Routes
Ex Ex2 Install Guide
1. Installation
Instructions
& Recommended
Pr ocedures
The Defuser EX system is ideal for small to mid-size vehicles, and comes packaged in an ordinary looking
license plate frame. It may be installed with or without the license plate frame as needed.
The Defuser EX2 system is recommended for larger size vehicles, or when a front license plate mount
is not used on the vehicle. The system includes two separate Defuser modules with no license plate frames.
LASER DEFUSER EX
(FRONT LICENSE PLATE MOUNT WITH FRAME)
1. Remove the mounting bolts and any existing frame or cover from the license plate. Remove license plate.
2. Position the Laser Defuser EX around the existing front license plate and mount it against the factory license
plate bracket. Use the existing mounting bolts or K40 supplied nylon bolts to secure the Laser Defuser EX
frame and license plate to the bracket.
NOTE: On vehicles that have only one set of bracket mounting holes, it is recommended that the Laser
Defuser EX and the license plate be bolted together to eliminate any vibration.
3. For proper performance, the Defuser EX must be mounted completely level. A unit which is positioned up,
down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several hundred feet
(see diagram A1).
To assure the Defuser EX is properly leveled, insert the rod on the K40 supplied level into the leveling assem-
bly hole located on the top of the Defuser EX frame (see diagram A2). Be sure that the vehicle is on a level
surface before checking installation.
Enlarged Enlarged Enlarged
View View View
G BEAM
JAMMING BEAM JAMMIN
JAMMIN
G BEAM
LASER LASER LASER
DEFUSER EX DEFUSER EX DEFUSER EX
CORRECT NO NO
DIAGRAM A1
Use the K40 supplied nylon nuts LASER
DEFUSER
and bolts to correct either up or
down as needed (see diagram A3).
FACTORY
4. Route the black cable into the engine MOUNTING
LOCATION
compartment either through the grill
or under the bumper. Connect wires
per the separate enclosed block
diagram sheet.
MOUNTING NUTS
DIAGRAM A2 DIAGRAM A3
NOTE: On some vehicles, it may be necessary to adjust or reposition the factory license plate bracket to
achieve the desired level installation.
2. LASER DEFUSER EX & EX2
(FRONT CUSTOM MOUNT WITHOUT FRAME)
NOTE: If using an EX system, first separate the module from the license plate frame by removing the
two screws on the backside of the frame.
1. For the single Defuser EX, choose a mounting location near the center of the vehicle that has a clear, unob-
structed view of the road . Units which are mounted off center, are recessed into the vehicle, or which are
obstructed in any way will not perform properly (see diagram B1).
CENTERED & UN- DO NOT PUT BEHIND GRILL
OBSTRUCTED DO NOT MOUNT OFF CENTER
DO NOT OBSTRUCT VIEW
DIAGRAM B1
2. For the dual Defuser EX2, choose separate mounting locations on either side of the license plate area and/or
center of the vehicle. For proper performance, the EX2 modules should be spaced 18" apart from one
another, and cannot be obstructed in any way or recessed into the vehicle (see diagram B2).
CORRECTLY SPACED DO NOT PUT BEHIND GRILL DO NOT SPACE MODULES
& UNOBSTRUCTED DO NOT OBSTRUCT VIEW MORE THAN 18” APART
DIAGRAM B2
3. If utilizing the supplied universal mounting bracket(s), determine which holes will be used to mount the
Defuser module(s) to the vehicle. Remove the unused mounting tabs on the bracket(s) as needed.
4. Apply the supplied double stick tape directly to the Defuser module(s) and attach the module(s) to the
universal mounting bracket(s) with the included 1/4” screws ( diagram B3).
BRACKET
BRACKET
TAPE
TAPE
1/4”
SCREW 1/4”
SCREW
LASER DEFUSER
WITHOUT LASER DEFUSER WITH
HORIZONTAL HORIZONTAL
TABS TABS
1/4” SCREW 1/4” SCREW
Diagram B3
3. 5. Install the Defuser module(s) to
the desired mounting surface Enlarged Enlarged
using the included 3/4” screws View View
or nylon mounting nuts and AM
BE
bolts. ING
MM
JA
6. For proper performance, the JAMMING BEAM
Defuser EX and EX2 must be
mounted completely level. A
LASER DEFUSER LASER DEFUSER
unit which is positioned up,
down, or to the side by as little
as 1° can reduce jamming effec- CORRECT NO
tiveness by as much as several
hundred feet (see diagram B4).
JAMMING BEAM
JAMMING BEAM
Be sure that the vehicle is on a
JAMM
G BEAM
Enlarged Enlarged
level surface before checking View View
ING BE
JAMMIN
installation.
AM
LASER DEFUSER(S) LASER DEFUSER(S)
CORRECT NO
DIAGRAM B4
To assure the Defuser module(s) is/are properly leveled, insert the rod
on the K40 supplied level into the leveling assembly hole located near
the middle of the Defuser module(s)(see diagram B5).
7. Route the black cable(s) into the engine compartment, either through
the grill or under the bumper. Connect the Defuser EX or EX2 wires
per the separate enclosed block diagram sheet.
DIAGRAM B5
LASER DEFUSER EX & EX2
(REAR LICENSE PLATE MOUNT WITHOUT FRAME)
NOTE: If using an EX system, first separate the module from the license plate frame by removing the
two screws on the backside of the frame.
1. Remove the mounting bolts and any existing frame or cover from the rear license plate. Remove license plate.
2. Remove the three unused horizontal mounting tabs from the top of the supplied universal mounting bracket.
3. Apply the supplied double stick tape directly to the Defuser module and attach it to the mounting bracket with
the included 1/4” screws. Position the Defuser module against the license plate and mount it to the factory
license plate bracket using the existing mounting bolts or K40 supplied nylon bolts (see diagram C1)
40
DIAGRAM C1
4. 4. For proper performance, the Defuser module must be mounted completely level. A module which is posi-
tioned up, down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several
hundred feet (see diagram C2). To assure the Defuser module is properly leveled, insert the rod on the K40
supplied level into the leveling assembly hole located near the middle of the Defuser module (see diagram C3).
Be sure that the vehicle is on a level surface before checking installation.
5. Route the black cable into the trunk. Connect wires per the separate enclosed block diagram sheet.
LASER DEFUSER LASER DEFUSER LASER DEFUSER
FACTORY FACTORY FACTORY
MOUNTING MOUNTING MOUNTING
LOCATION LOCATION LOCATION
DIAGRAM C2 DIAGRAM C3
LASER DEFUSER EX
(REAR LICENSE PLATE MOUNT WITH FRAME)
1. Remove the mounting bolts and any existing frame or cover from the license plate. Remove license plate.
2. Position the Laser Defuser EX around the existing rear license plate and mount it against the factory license
plate bracket. Use the existing mounting bolts or K40 supplied nylon bolts to secure the Laser Defuser EX
frame and license plate to the bracket.
NOTE: On vehicles that have only one set of bracket mounting holes, it is recommended that the Laser
Defuser EX and the license plate be bolted together to eliminate any vibration.
3. For proper performance, the Defuser EX must be mounted completely level. A unit which is positioned up,
down, or to the side by as little as 1° can reduce jamming effectiveness by as much as several hundred feet
(see diagram D1). To assure the Defuser EX is properly leveled, insert the rod on the K40 supplied level into
the leveling assembly hole located on the top of the Defuser EX frame (see diagram D2). Be sure that the
vehicle is on a level surface before checking installation.
4. Use the K40 supplied nylon nuts and bolts to correct either up or down as needed ).
5. Route the black cable into the trunk. Connect wires per the separate enclosed block diagram sheet.
LASER DEFUSER LASER DEFUSER LASER DEFUSER
FACTORY FACTORY FACTORY
MOUNTING MOUNTING MOUNTING
LOCATION LOCATION LOCATION
44678 6/07 DIAGRAM D1 DIAGRAM D2