SlideShare a Scribd company logo
1 of 16
Download to read offline
PRESS PROBLEMS
Press problems from examination point of view can be classified into two:

1.    Problems regarding suitability of the press from force and energy point of view

2.    Problems regarding shout height of the press.

Kinematically a mechanical press can be viewed as follows:




OA= crank length = r. Therefore Stroke Length is given as S = 2 x OA = 2 r

                        L = length of connecting rod.

At some angle , the sliding point on the under face of the ram will be at a distance of H from BDC.
Since length of the connecting link AB is large compared to length of crank OA, the inclination of AB
with respect to the vertical central line can be neglected. i.e. = 0.

Thus any force reaction R acting at a point B can be taken as acting at point A as shown.

Therefore the torque at point O =T = R x OA sin       = F x OA sin   = F x r sin

                                                      1
[F = force exerted by the press which is equal to the resistance experienced by the ram =R]

A press is designed to exert defined amount of force at given crank angle . It means main crankshaft is
designed keeping in view some value of torque. In other words, torque provided by a press is fixed.

                         T = F * r sin

                                 T
                         F
                              r sin

                                1
                         F
                              sin


Where ‘r’ is fixed for a particular operation and dependent on the stroke length.

Therefore force available from press varies with crank angle. F is minimum when         90 and
theoretically infinite when      0 or 180 i.e. at dead ends.




                                                     2
Though press is capable of exerting infinite force at dead ends, press members such as cranks and
connecting links cannot be designed for infinite load. They have to be designed for finite force. This safe
finite force is to be determined by the dimensions, strength and allowable deflections of press components
such as press frame, connecting link, crank etc. This safe value is known as press capacity and specified
as tonnage at crank angle. Let us say press of 63T at 20  .

Daylight: The maximum clear distance between the two pressing surfaces of a press when surfaces are in
the usable open position. When a bolster plate is supplied it is considered as the pressing surface.

The velocity of ram can be computed using following formula:

         N S Sin                                S
V                        0.105 N h          (     1)
           60                                   h

where N = Number of strokes per minute (SPM),          h = slide location above ( or before) BDC

       S = stroke,          = crank angle

Shut height: For a press, the distance from the top of the bed to the bottom of the slide with the stroke
down and adjustment up. In general, it is the maximum die height that can be accommodated for normal
operation, taking the bolster plate into consideration. Shut height is always measured at BDC. There are
two shut heights maximum and minimum




                                                       3
Position (1) = position corresponding to maximum stroke where Smax= 2 x r1

Position(2) = position corresponding to minimum stroke where Smin = 2 * r2

                        r1     r2 = (Smax Smin)/2

                                                        maximum stroke minimum stroke
Thus,   MaxDLH = MinDLH + Press Adjustment +
                                                                      2

If maximum DLH for a given stroke length, which lies between minimum and maximum stroke length, is
to be found following formulation can be used.

                                                                max stroke min stroke
                        Max DLH stroke = Max DLH
                                                                          2


            DLH                   STROKE             STROKE LENGTH                PRESS
                                 POSITION                                      ADJUSTMENT

        MAXIMUM                       TDC                  MAXIMUM                      UP

         MINIMUM                      TDC                  MINIMUM                 DOWN


ENERGY OVERLOADING: The energy needed for cutting and forming operations during each stroke
is supplied by flywheel which slows down to a permissible percentage, usually 10 20% of its idle speed.
For example, if 10% slow down is permissible

                                                               N1
                        (N0 N1)/N0 = 0.1, which gives               0 .9 .
                                                               N0

Total energy of the flywheel

                                   I 2       I * 2 N2
                        E FT                           = (constant) * N2          =          K N2
                                    2        2       2
                                                  60

Where                   N0        =         idle flywheel rpm

                        N1        =         flywheel rpm after stroke

                        N         =         flywheel rpm

                        I         =         M.I. of the flywheel

                                  =         angular velocity

                                                       4
The total energy supplied (ES) by flywheel includes energy required to overcome friction and elastic
deflections. The electric motor must restore its ideal speed before stroke. The time available between
two strokes depends on type of operation (namely) whether it is continuous or intermittent. In continuous
type of operation, permissible slowdown is 10% and in discontinuous 20%.

                          I * 2 N1 2
The energy after stroke =
                          2    60 2

                                                   2           2
                        ES = EFT(N0) EFT(N1) = K N 0          N1

                                      2     2                 2
                         ES      K( N 0    N1 )              N1
                                                    1
                        E FT              2                   2
                                     K( N 0 )                N0

                                N1
With a slowdown of 20% =                0.8
                                N0

                         ES
                                 1     0.8 2      0.36
                        E FT

This energy supplied must be more than the required energy.

Shut heights for the press

     Shut Height             Stroke Position                  Stroke        Press Adjustment

 Maximum                          BDC               Maximum                        UP

 Minimum                          BDC               Minimum                      DOWN




                                                         5
Problem 1: A press has a maximum DLH (day light height) of 500 mm and a ram adjustment of 60
mm. Calculate maximum and minimum shut height value for a press tooling if the bolster plat
provided on the press bed has a thickness of 80 mm. The press has a variable stoke with maximum
stroke and minimum stroke of150 mm and 10 mm respectively.

Solution

Minimum Shut Height = Maximum DLH Maximum Stroke Press Adjustment
(In case of max DLH, press adjustment is UP but in case of minimum shut height, if is down).

Minimum Shut Height = 500 150 60 = 290 mm
Maximum Shut Height = minimum shut height (SH) + press adjustment +

           Max stroke Min stroke
                     2

                                                (150       10 )
                                 = 290 + 60 +                     = 420 mm
                                                       2

To calculate shut height for a tooling, thickness of bolster plates must be deducted from press shut
heights.


Max SH for die = 420 80 = 340 mm
Min SH for die = 290 80 = 210 mm




                                                     6
Problem 2: A press has minimum DLH 325 mm and Adjustment of ram is 75 mm. Stroke is
variable and can be varied from 12.5 mm to 100 mm. If the bolster plate provided has a thickness
of 80 mm, calculate maximum and minimum shut height for a die.

Solution
Maximum DLH = minimum DLH + (r1             r2) + P.A. (press adjustment)

                         100 12 .5
                = 325                   75 = 443.75 mm
                              2


Minimum shut height     = Max DLH       Max Stroke         press adjustment = 443.75   100    75

                        = 268.75 mm
                                                              max stroke min stroke
Maximum shut height = minimum shut height + PA +
                                                                           2

                        = 268.75 + 75 + 43.75 = 387.5 mm


Max shut height for tooling       = 387.5    bolster plate thickness (= 80 mm) = 387.5       80 = 307.5 mm


Min shut height for tooling       = 268.75     80 = 188.75 mm



Problem 3: A press has maximum DLH 500 mm and a ram adjustment of 60 mm. Stroke can be varied
from 10 mm to 150 mm. Calculate minimum and maximum shut height for a press tool for stroke of 100
mm and bolster plate thickness of 80 mm.

Solution: First it is necessary to calculate max DLH for stroke length equal to 100 mm as maximum DLH
given (500 mm) corresponds to maximum stroke of 150 mm stroke.


                max stroke(r1 ) given stroke(r )                  (150 100 )
= MaxDLH                                         = 500                         = 475 mm
                               2                                       2
Min shut height of press = max DLH          stroke   PA (since PA is up in case of max DLH but down in
case of min SH)
  = 475 100 60 = 315 mm

Max SH of press = Min SH + PA = 315 + 60 = 375 mm

                                                       7
OR




Max SH of press = Max DLH100     Stroke = 475   100 =375 mm

Min SH of press = Max SH    PA = 375   60= 315 mm

Max Shut height for die = Max SH for press bolster plate thickness = 375 80 = 295 mm
Min shut height for die = Min SH for press bolsters plate thickness = 315 80 = 235 mm


Problem 4: A press has minimum of DLH 325 mm and press adjustment of slide of 75 mm. Stroke
can be varied from 12.5 mm to 100 mm. Bolster plate thickness is 75 mm. Calculate permitted
shut height for die if stroke is fixed at 50 mm.

Solution

                                                                   Given stroke min stroke
Minimum DLH for 50 mm stroke = min DLH (for 12.5 mm stroke) +
                                                                              2

                                       (50 12 .5)
                              = 325                  = 343.75 mm
                                           2

                                                8
Minimum shut height of the press = min DLH (for 50 mm stroke) stroke = 343.75                      50 =293.75 mm
Maximum SH of the press = min SH + PA = 293.75 + 75 = 368.75 mm

Maximum SH for the die = max SH for press                   bolster plate thickness = 368.75   75= 293.75 mm

Minimum SH for the die = min SH for press                  bolster plate thickness = 293.75    75 = 218.75 mm

Problem 5: A press is designed to offer 90 ton of force at 20  crank angle with a stroke of 15 cm.
Stroke is variable from 1 cm to 15 cm. Calculate tonnage available when ram is 3 cm above its
BDC. Take stroke length equal to 10 cm.

Solution
       Given h = 3 cm, s = 10 cm.
            h 1 cos
                            Where         = crank angle from BDC
            s        2
            3     1 Cos
            10         2
=>               66 .42 

As we know that
                             s
T = F x r x sin       = F*       * sin = constant
                             2
              s                s
=> T       F * 1 * sin 1 = F2 * 2 * sin 2
            1
               2                2
F1 = force available 90T at crank angle 1                  20 and stroke s1 = 15 cm.
F2 = force available at 3 cm above BDC and stroke s2 = 10 cm,                   66.42
       15                          10
90 *        * sin(20  )    F2 *        * sin(66 .42  )
       2                           2

=>F2 = 50.4T i.e. tonnage available when ram is 3 cm above the BDC is 50.4T

Problem 6: Check regarding the suitability of the press with following press data for blanking and
drawing operation with combination die.
                                         
Capacity of the press tool is 150 T at 20 from BDC
Stroke length=120mm
Total fly wheel energy = 180T cm
Permitted slowdown of speed = 20%
Blanking load = 30T
Drawing force = 10T
Blank holding force = 3T
Depth of cup = 35 mm = 3.5 cm
Stock thickness = 1 mm = 0.1 cm
Percent Penetration = 30%


                                                                 9
Solution:

I. Suitability of press from tonnage point of view:

Total load on the press = blanking load + drawing load + blank holding force = 40 + 10 + 3 = 53 T


Since depth of drawn cup is 3.5 cm, drawing will commence at height of 3.5 cm from BDC assuming
bottom edge of the cup is at BDC. Further, force increases towards the BDC. Now, we will determine
tonnage available at a height of 3.5 cm.

h = 3.5 cm, assuming stroke = 12 cm.

h          1 cos
S            2

3.5         1 cos
                               gives    = 65.37
12            2

Since torque transmitted by crank shaft is constant,
                 S1                    S2
T          F1       sin    1    F2          sin    2
                 2                     2

As stroke length is unchanged, S1                 S2

F2         sin    2   F1 sin      1



F2 sin (65.4 )            150 sin (20 )

      F2        56 .44 T

Conclusion: As available tonnage F2 is greater than the required tonnage (53T), the given press is
suitable to carry out the given operations from tonnage point of view.

II.             Suitability of the press from the energy point of view


Total energy required = Energy for blanking + Energy for drawing + Energy for blank holding

Energy required for blanking = Force x distance = F x K x t = 40 x 0.3 x 0.1 = 1.2T.cm

Energy required for drawing = Force x distance (= cup depth) = 10 x 3.5 = 35 T. cm

Energy for blank holding = Blank holding force x distance (= cup depth) = 3 x 3.5 = 10.5 T.cm

Total energy required = 1.2 + 35 + 10.5 = 46.7 T. cm

                                                          10
Energy available from the flywheel:

Permitted slowdown of speed = 0.2

N0         N1                     N1
                0.2 gives              0.8
      N0                          N0

                         Energy supplied (ES )                 2
                                                              N1
We know that,                                            1            1   (0.8) 2
                  Total energy of the flywheel(E FT )          2
                                                              N0

                   ES
                         = 0.36
                  E FT

                  ES     E FT * 0.36 = 64.8 T. cm



Conclusion: Since the energy supplied (64.8 T. cm) is more than energy required (46.7T.cm); the press is
suitable from energy point of view. Thus, the press is suitable from both tonnage and energy point of
view.


Problem 7: Tonnage rating of a given press is 160 T at 20 crank angle from BDC. Stroke is
variable from 10 mm to 120 mm in steps of 10 mm. The ram can be adjusted by 100 mm.
Maximum DLH of the press is 500 mm. Total energy of the flywheel is 180T.cm.Permissible
slowdown in speed is 20%. If it is decided to use stroke of 100 mm, calculate


1.     The maximum and minimum shut height for a combination die.

2.     Tonnage available at 25 mm from BDC.

3.     Check the suitability of press for following operation: Blanking and drawing with the help of
       combination die.
         Blanking load is 45T. Drawing force is 10T. Blank holding force is 3T. Cup depth is 20 mm.
         Stock thickness is 1.5 mm. Percent penetration is 30%.


Solution

(i)    Maximum DLH at 120 mm (max stroke) is equal to 500 mm. Therefore, it is necessary to find the
       max DLH at 100 mm stroke.
                                                                    (Max stroke         given strok)
       Max DLH at 100 mm stroke = max DLH at 120 mm stroke
                                                                                    2
                                                    11
(120 100)
                                              = 500                  = 490mm
                                                               2

Maximum SH of the press             = Max DLH at 100 m stroke - stroke = 490 100 = 390 mm

Minimum SH of the press             = Max SH           press adjustment= 390 100 = 290 mm

Since there is no mention of bolster plate, we may assume bolster plate thickness of 60mm.

Maximum shut height of combination die is =390-60= 330mm

Minimum shut height of combination die is =290-60= 230mm

(ii) Suitability of the press from the tonnage point of view

Determining force availability at height of 25 mm from BDC

                            h= 25 mm = 2.5 cm,                         S = 100 mm = 10 cm

                               h     1 cos       2

                               S        2

                             2 .5        1 cos 2
                             10             2

      2     60

             S1                          S2
T     F1          sin   1      F2              sin     2
             2                           2

F1        160 T, 1      20 , S1         12 cm

F2 = ?            2 = 60 ,     S 2 = 10 cm

Since max tonnage is available at max tonnage

            12                            10
     160          sin (20 )        F2               sin (60 )
             2                             2

     F2     75 .8 T i.e. Force offered by the press at a height of 25 mm from BDC.

Height of the cup is 20 m and total force required for blanking and drawing is 58 T (45 + 10 + 3). As
force at height of 25 mm from BDC is greater than the required, force at 20 mm from BDC must be far
greater than required (58 T). Hence, the given press is suitable to carry out given operations from tonnage
point of view.

                                                                  12
Suitability of the press from the energy point of view

Total energy required = blanking + drawing + blank holding

                      = (force x K x t 0 ) + (drawing load x depth of cup)+ (Blank holding force * depth
of cup)

                         = (45 * 0.33 * 0.15) + (10 * 2) + (3 * 2) = 28.23 T. cm

Energy supplied by the flywheel when permitted slowdown is 20%….

                                  N                       N1
                         1               0.2 that gives        0.8
                                  N0                      N0

                                   Energy supplied (E S )                   2
                                                                           N1
                                                                      1           1   (0.8) 2
                         Total energy of the flywheel(E FT )                2
                                                                           N0

                             ES
                                       0.36
                         E FT

                         ES       EFT     0.36 = 180 x 0.36 = 64.8 T.cm


Energy supplied by the flywheel (64.8 T.cm) is substantially more than required for the operation (28.23
T.cm). The press is suitable from the energy point of view.

In sum, the given press is suitable to carry out given operations from tonnage as well as energy
point of view.


Problem 8: The punch force required for a cup drawing operation is 10 T. Depth of the cup is 35
mm. An air operated blank holder provides a force of 3 T to prevent wrinkling. A 45 T capacity
press having total flywheel energy = 33 T. cm is available for use. Another press of capacity 150 T
and flywheel energy 180 T. cm is also available. Permissible slowdown of speed is 20%. Calculate
total energy required and select a press.

Solution

Total tonnage required to draw the cup =10+3=13 Ton

Energy required for cup drawing = Force x depth of cup = (10 + 3) x 3.5 = 45.5 T.cm

First press is unsuitable to carry out the operation from energy point of view.


                                                          13
N1
        0.8                              From given data
N0

       Energy supplied (ES )                   2
                                              N1
                                          1             1   (0.8) 2 =0.36
Total energy of the flywheel(E FT )            2
                                              N0


Energy Available from the second Press

                          ES   EFT 0.36 = 180 x 0.36 = 64.8 T. cm




The available energy from the second press is more than the energy required for the operation and
therefore this press is suitable for the operation from energy point of view and can be selected.

Problem 9: A press is designed for giving 120 t at 30 crank from BDC, when stroke is 20 cm. Prepare a
monograph from BDC. From the monograph explain:

1. Overloading of torque without overloading capacity.

2. Overloading of capacity without overloading of torque.


Solution: We know that

                      S
h= r     r cos    =        (1 cos )
                      2


   h     (1 cos )
   s        2


Torque provided by a press remains constant
                                                   14
S                                          2T
                         T       F      sin            which gives       F                ………….(1)
                                      2                                        S sin
        In given press T is equal to

                                           20
                         T      120                sin (30 ) = 600 T. cm
                                            2

                                   2 600     60
                        F =              =                  …………………………………………(2)
                                  20 sin   sin


For equation (1) and (2), common variable is

                           0         30         45        60       75        90    120    150    180

               F                     120        85        69       62        60    69     120

               h/s         0         0.07       0.15     0.25     0.37       0.5   0.75   0.93   1.0



A graph can be drawn to show up the relationship.


1. Overloading of torque without overloading capacity

Press will get overloaded if load requirement is more than 120 T. Any point above ZZ means overloading
of press and press members will fail. One may select any point on any line like A1 where press will be
under loaded. Any point on curve like A2 will have torque equal to that available on the press i.e.
                          3
600Tcm. Select any point A at             = 60 and load equal to F = 80T which is less than rated capacity of
120 T meaning that it is under loaded.

                                      S                        20
                         T      F            sin       80         sin (60 )
                                      2                         2

                               = 692.8 T. cm which is greater than available torque (600 T.cm)

Thus, at the point A3 there is overloading of torque without overloading the capacity.

Any point between A 1 to A 2 will not cause overloading of torque and obliviously not causing
overloading.

Take            F = 80T,       and     = 45 ,

                                       S                        20
                        T = F                sin        80         sin (45 ) = 565.68 T.cm
                                       2                         2
                                                             15
2. Overloading of capacity without overloading torque

Take point B    where F = 140 T and        = 15

Since the load is more than 120 T, the press is overloaded

          S                  20
T    F      sin       140       sin (15 ) = 362.34 T. cm (less than 600T cm.)
          2                  2

This is the case of overloading press capacity (F = 140 T beyond 120 T) without overloading the torque.




                                                    16

More Related Content

What's hot

Unit 2 Design Of Shafts Keys and Couplings
Unit 2 Design Of Shafts Keys and CouplingsUnit 2 Design Of Shafts Keys and Couplings
Unit 2 Design Of Shafts Keys and CouplingsMahesh Shinde
 
brakes and dynamometer
brakes and dynamometerbrakes and dynamometer
brakes and dynamometerGulfaraz alam
 
Types of Dynamometers
Types of DynamometersTypes of Dynamometers
Types of DynamometersHarsh Pathak
 
Friction clutches brakes and dynamo-meters
Friction clutches brakes and dynamo-metersFriction clutches brakes and dynamo-meters
Friction clutches brakes and dynamo-metersDr.Vikas Deulgaonkar
 
DME intro and design of cotter joint may 2020
DME intro and design of cotter joint may 2020DME intro and design of cotter joint may 2020
DME intro and design of cotter joint may 2020Gaurav Mistry
 
MODULE 5_Deisign for Fatigue Loads (1).pdf
MODULE 5_Deisign for Fatigue Loads (1).pdfMODULE 5_Deisign for Fatigue Loads (1).pdf
MODULE 5_Deisign for Fatigue Loads (1).pdfGokulThalapthyHarish
 
Milling notes (man. sc. ii)
Milling notes (man. sc. ii)Milling notes (man. sc. ii)
Milling notes (man. sc. ii)Manoj Yadav
 
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECH
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECHMilling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECH
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECHnaanmech123
 
Shaft subjected to bending moment only (2)
Shaft subjected to bending moment only (2)Shaft subjected to bending moment only (2)
Shaft subjected to bending moment only (2)abdul ahad noohani
 
Design of shafts couplings ppt
Design of shafts couplings  pptDesign of shafts couplings  ppt
Design of shafts couplings pptnsvnhanu
 
Springs - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-IISprings - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-IIDr. L K Bhagi
 
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINES
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINESUNIT III SHAPER, MILLING AND GEAR CUTTING MACHINES
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINESKarthik R
 

What's hot (20)

Unit 2 Design Of Shafts Keys and Couplings
Unit 2 Design Of Shafts Keys and CouplingsUnit 2 Design Of Shafts Keys and Couplings
Unit 2 Design Of Shafts Keys and Couplings
 
Unit 3.2 Design of Clutches
Unit 3.2 Design of ClutchesUnit 3.2 Design of Clutches
Unit 3.2 Design of Clutches
 
brakes and dynamometer
brakes and dynamometerbrakes and dynamometer
brakes and dynamometer
 
Types of Dynamometers
Types of DynamometersTypes of Dynamometers
Types of Dynamometers
 
Friction clutches brakes and dynamo-meters
Friction clutches brakes and dynamo-metersFriction clutches brakes and dynamo-meters
Friction clutches brakes and dynamo-meters
 
Press work
Press workPress work
Press work
 
Clutches
ClutchesClutches
Clutches
 
DME intro and design of cotter joint may 2020
DME intro and design of cotter joint may 2020DME intro and design of cotter joint may 2020
DME intro and design of cotter joint may 2020
 
MODULE 5_Deisign for Fatigue Loads (1).pdf
MODULE 5_Deisign for Fatigue Loads (1).pdfMODULE 5_Deisign for Fatigue Loads (1).pdf
MODULE 5_Deisign for Fatigue Loads (1).pdf
 
Governor
GovernorGovernor
Governor
 
Milling notes (man. sc. ii)
Milling notes (man. sc. ii)Milling notes (man. sc. ii)
Milling notes (man. sc. ii)
 
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECH
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECHMilling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECH
Milling machine-types-operations..etc..from L.NARAYANAN,M.E.,AP.MECH
 
Clutches
ClutchesClutches
Clutches
 
Unit 2b Power Transmission by Belts
Unit 2b Power Transmission by BeltsUnit 2b Power Transmission by Belts
Unit 2b Power Transmission by Belts
 
Types of dies
Types of diesTypes of dies
Types of dies
 
Shaft subjected to bending moment only (2)
Shaft subjected to bending moment only (2)Shaft subjected to bending moment only (2)
Shaft subjected to bending moment only (2)
 
Design of shafts couplings ppt
Design of shafts couplings  pptDesign of shafts couplings  ppt
Design of shafts couplings ppt
 
Springs - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-IISprings - DESIGN OF MACHINE ELEMENTS-II
Springs - DESIGN OF MACHINE ELEMENTS-II
 
DESIGN OF SHAFT
DESIGN OF SHAFTDESIGN OF SHAFT
DESIGN OF SHAFT
 
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINES
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINESUNIT III SHAPER, MILLING AND GEAR CUTTING MACHINES
UNIT III SHAPER, MILLING AND GEAR CUTTING MACHINES
 

Viewers also liked

Print media in Pakistan
Print media in PakistanPrint media in Pakistan
Print media in PakistanFakiha Rizvi
 
Challenges of social media analysis in the real world
Challenges of social media analysis in the real worldChallenges of social media analysis in the real world
Challenges of social media analysis in the real worldDiana Maynard
 
PAKISTAN RISE OF MEDIA HISTORY
PAKISTAN RISE OF MEDIA HISTORYPAKISTAN RISE OF MEDIA HISTORY
PAKISTAN RISE OF MEDIA HISTORYamanfoundation
 
Current Problems in the Media
Current Problems in the MediaCurrent Problems in the Media
Current Problems in the MediaMajid Heidari
 
Print Media - History of journalism
Print Media - History of journalismPrint Media - History of journalism
Print Media - History of journalismArzoo Sahni
 

Viewers also liked (6)

Print media in Pakistan
Print media in PakistanPrint media in Pakistan
Print media in Pakistan
 
Challenges of social media analysis in the real world
Challenges of social media analysis in the real worldChallenges of social media analysis in the real world
Challenges of social media analysis in the real world
 
PAKISTAN RISE OF MEDIA HISTORY
PAKISTAN RISE OF MEDIA HISTORYPAKISTAN RISE OF MEDIA HISTORY
PAKISTAN RISE OF MEDIA HISTORY
 
Current Problems in the Media
Current Problems in the MediaCurrent Problems in the Media
Current Problems in the Media
 
Print Media - History of journalism
Print Media - History of journalismPrint Media - History of journalism
Print Media - History of journalism
 
Role of media in Pakistan
Role of media in PakistanRole of media in Pakistan
Role of media in Pakistan
 

Similar to Press problems

Torsion-mmmmm-84739392727363638393999909
Torsion-mmmmm-84739392727363638393999909Torsion-mmmmm-84739392727363638393999909
Torsion-mmmmm-84739392727363638393999909elladanicaj
 
Torsion Hollow Shaft
Torsion Hollow ShaftTorsion Hollow Shaft
Torsion Hollow Shafttejasp
 
fdocuments.us_turning-moment-diagram-flywheel.ppt
fdocuments.us_turning-moment-diagram-flywheel.pptfdocuments.us_turning-moment-diagram-flywheel.ppt
fdocuments.us_turning-moment-diagram-flywheel.pptSukantaMandal17
 
4unit-200715014624 circular shaft - Copy.pptx
4unit-200715014624 circular shaft - Copy.pptx4unit-200715014624 circular shaft - Copy.pptx
4unit-200715014624 circular shaft - Copy.pptxPraveen Kumar
 
Basic of Clutches, kopling tidak tetap
Basic of Clutches, kopling tidak tetapBasic of Clutches, kopling tidak tetap
Basic of Clutches, kopling tidak tetapdodi mulya
 
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdf
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdfelectrical-engineering_engineering_power-electronics_dc-choppers_notes.pdf
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdfLucasMogaka
 
Dynamics of-machines-formulae-sheet
Dynamics of-machines-formulae-sheetDynamics of-machines-formulae-sheet
Dynamics of-machines-formulae-sheetAnjaneya Tiwari
 
Electrical Machine design
Electrical Machine designElectrical Machine design
Electrical Machine designAsifAdnanTajwer
 
Grinding and economics of machining operation
Grinding and economics of machining operationGrinding and economics of machining operation
Grinding and economics of machining operationkajavarun
 
Engineering science lesson 7
Engineering science lesson 7Engineering science lesson 7
Engineering science lesson 7Shahid Aaqil
 

Similar to Press problems (20)

TORSION (MECHANICS OF SOLIDS)
TORSION (MECHANICS OF SOLIDS)TORSION (MECHANICS OF SOLIDS)
TORSION (MECHANICS OF SOLIDS)
 
Torsion
TorsionTorsion
Torsion
 
Torsion-mmmmm-84739392727363638393999909
Torsion-mmmmm-84739392727363638393999909Torsion-mmmmm-84739392727363638393999909
Torsion-mmmmm-84739392727363638393999909
 
Flywheel.pptx
Flywheel.pptxFlywheel.pptx
Flywheel.pptx
 
Torsion Hollow Shaft
Torsion Hollow ShaftTorsion Hollow Shaft
Torsion Hollow Shaft
 
Turning moment-diagram-flywheel
Turning moment-diagram-flywheelTurning moment-diagram-flywheel
Turning moment-diagram-flywheel
 
fdocuments.us_turning-moment-diagram-flywheel.ppt
fdocuments.us_turning-moment-diagram-flywheel.pptfdocuments.us_turning-moment-diagram-flywheel.ppt
fdocuments.us_turning-moment-diagram-flywheel.ppt
 
4unit-200715014624 circular shaft - Copy.pptx
4unit-200715014624 circular shaft - Copy.pptx4unit-200715014624 circular shaft - Copy.pptx
4unit-200715014624 circular shaft - Copy.pptx
 
TORSION,BENDING SHEAR ..pdf
TORSION,BENDING SHEAR  ..pdfTORSION,BENDING SHEAR  ..pdf
TORSION,BENDING SHEAR ..pdf
 
Basic of Clutches, kopling tidak tetap
Basic of Clutches, kopling tidak tetapBasic of Clutches, kopling tidak tetap
Basic of Clutches, kopling tidak tetap
 
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdf
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdfelectrical-engineering_engineering_power-electronics_dc-choppers_notes.pdf
electrical-engineering_engineering_power-electronics_dc-choppers_notes.pdf
 
flywheel
 flywheel flywheel
flywheel
 
Dynamics of-machines-formulae-sheet
Dynamics of-machines-formulae-sheetDynamics of-machines-formulae-sheet
Dynamics of-machines-formulae-sheet
 
Unit5-KOM
Unit5-KOMUnit5-KOM
Unit5-KOM
 
Performance parameters
Performance parametersPerformance parameters
Performance parameters
 
Electrical Machine design
Electrical Machine designElectrical Machine design
Electrical Machine design
 
Grinding and economics of machining operation
Grinding and economics of machining operationGrinding and economics of machining operation
Grinding and economics of machining operation
 
Engineering science lesson 7
Engineering science lesson 7Engineering science lesson 7
Engineering science lesson 7
 
Axial Flow Turbine.ppt
Axial Flow Turbine.pptAxial Flow Turbine.ppt
Axial Flow Turbine.ppt
 
flywheel
flywheelflywheel
flywheel
 

More from VJTI Production

More from VJTI Production (20)

Compensation
CompensationCompensation
Compensation
 
Job design
Job designJob design
Job design
 
Human nature and behaviour
Human nature and behaviourHuman nature and behaviour
Human nature and behaviour
 
Group behaviour
Group behaviourGroup behaviour
Group behaviour
 
Motivation
MotivationMotivation
Motivation
 
Optimization assignment 2
Optimization assignment 2Optimization assignment 2
Optimization assignment 2
 
Optimization assignment 3
Optimization assignment 3Optimization assignment 3
Optimization assignment 3
 
Optimization assignment 1
Optimization assignment 1Optimization assignment 1
Optimization assignment 1
 
Working capital
Working capitalWorking capital
Working capital
 
Capital budgeting techniques
Capital budgeting techniquesCapital budgeting techniques
Capital budgeting techniques
 
Market supply demand and market equilibrium
Market supply demand and market equilibriumMarket supply demand and market equilibrium
Market supply demand and market equilibrium
 
8. leadership
8. leadership8. leadership
8. leadership
 
7. communication
7. communication7. communication
7. communication
 
6. planning
6. planning6. planning
6. planning
 
5. decision making
5. decision making5. decision making
5. decision making
 
Final accounting assignment problems
Final accounting assignment problemsFinal accounting assignment problems
Final accounting assignment problems
 
Final account trading account pl acc balance sheet
Final account trading account pl acc balance sheetFinal account trading account pl acc balance sheet
Final account trading account pl acc balance sheet
 
4. organizational structure
4. organizational structure4. organizational structure
4. organizational structure
 
3. management contingency
3. management contingency3. management contingency
3. management contingency
 
2. scientific management
2. scientific management2. scientific management
2. scientific management
 

Recently uploaded

Male Infertility, Antioxidants and Beyond
Male Infertility, Antioxidants and BeyondMale Infertility, Antioxidants and Beyond
Male Infertility, Antioxidants and BeyondSujoy Dasgupta
 
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdf
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdfCONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdf
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdfDolisha Warbi
 
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdf
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdfPAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdf
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdfDolisha Warbi
 
Pharmacokinetic Models by Dr. Ram D. Bawankar.ppt
Pharmacokinetic Models by Dr. Ram D.  Bawankar.pptPharmacokinetic Models by Dr. Ram D.  Bawankar.ppt
Pharmacokinetic Models by Dr. Ram D. Bawankar.pptRamDBawankar1
 
Female Reproductive Physiology Before Pregnancy
Female Reproductive Physiology Before PregnancyFemale Reproductive Physiology Before Pregnancy
Female Reproductive Physiology Before PregnancyMedicoseAcademics
 
ORAL HYPOGLYCAEMIC AGENTS - PART 2.pptx
ORAL HYPOGLYCAEMIC AGENTS  - PART 2.pptxORAL HYPOGLYCAEMIC AGENTS  - PART 2.pptx
ORAL HYPOGLYCAEMIC AGENTS - PART 2.pptxNIKITA BHUTE
 
Basic structure of hair and hair growth cycle.pptx
Basic structure of hair and hair growth cycle.pptxBasic structure of hair and hair growth cycle.pptx
Basic structure of hair and hair growth cycle.pptxkomalt2001
 
Role of Soap based and synthetic or syndets bar
Role of  Soap based and synthetic or syndets barRole of  Soap based and synthetic or syndets bar
Role of Soap based and synthetic or syndets barmohitRahangdale
 
Different drug regularity bodies in different countries.
Different drug regularity bodies in different countries.Different drug regularity bodies in different countries.
Different drug regularity bodies in different countries.kishan singh tomar
 
Male Infertility Panel Discussion by Dr Sujoy Dasgupta
Male Infertility Panel Discussion by Dr Sujoy DasguptaMale Infertility Panel Discussion by Dr Sujoy Dasgupta
Male Infertility Panel Discussion by Dr Sujoy DasguptaSujoy Dasgupta
 
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdf
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdfSGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdf
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdfHongBiThi1
 
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptx
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptxDNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptx
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptxMAsifAhmad
 
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdf
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdfSGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdf
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdfHongBiThi1
 
CPR.nursingoutlook.pdf , Bsc nursing student
CPR.nursingoutlook.pdf , Bsc nursing studentCPR.nursingoutlook.pdf , Bsc nursing student
CPR.nursingoutlook.pdf , Bsc nursing studentsaileshpanda05
 
MedMatch: Your Health, Our Mission. Pitch deck.
MedMatch: Your Health, Our Mission. Pitch deck.MedMatch: Your Health, Our Mission. Pitch deck.
MedMatch: Your Health, Our Mission. Pitch deck.whalesdesign
 
Neurological history taking (2024) .
Neurological  history  taking  (2024)  .Neurological  history  taking  (2024)  .
Neurological history taking (2024) .Mohamed Rizk Khodair
 
blood bank management system project report
blood bank management system project reportblood bank management system project report
blood bank management system project reportNARMADAPETROLEUMGAS
 
Red Blood Cells_anemia & polycythemia.pdf
Red Blood Cells_anemia & polycythemia.pdfRed Blood Cells_anemia & polycythemia.pdf
Red Blood Cells_anemia & polycythemia.pdfMedicoseAcademics
 
Physiology of Smooth Muscles -Mechanics of contraction and relaxation
Physiology of Smooth Muscles -Mechanics of contraction and relaxationPhysiology of Smooth Muscles -Mechanics of contraction and relaxation
Physiology of Smooth Muscles -Mechanics of contraction and relaxationMedicoseAcademics
 

Recently uploaded (20)

Male Infertility, Antioxidants and Beyond
Male Infertility, Antioxidants and BeyondMale Infertility, Antioxidants and Beyond
Male Infertility, Antioxidants and Beyond
 
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdf
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdfCONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdf
CONNECTIVE TISSUE (ANATOMY AND PHYSIOLOGY).pdf
 
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdf
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdfPAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdf
PAIN/CLASSIFICATION AND MANAGEMENT OF PAIN.pdf
 
Pharmacokinetic Models by Dr. Ram D. Bawankar.ppt
Pharmacokinetic Models by Dr. Ram D.  Bawankar.pptPharmacokinetic Models by Dr. Ram D.  Bawankar.ppt
Pharmacokinetic Models by Dr. Ram D. Bawankar.ppt
 
Female Reproductive Physiology Before Pregnancy
Female Reproductive Physiology Before PregnancyFemale Reproductive Physiology Before Pregnancy
Female Reproductive Physiology Before Pregnancy
 
ORAL HYPOGLYCAEMIC AGENTS - PART 2.pptx
ORAL HYPOGLYCAEMIC AGENTS  - PART 2.pptxORAL HYPOGLYCAEMIC AGENTS  - PART 2.pptx
ORAL HYPOGLYCAEMIC AGENTS - PART 2.pptx
 
Basic structure of hair and hair growth cycle.pptx
Basic structure of hair and hair growth cycle.pptxBasic structure of hair and hair growth cycle.pptx
Basic structure of hair and hair growth cycle.pptx
 
Role of Soap based and synthetic or syndets bar
Role of  Soap based and synthetic or syndets barRole of  Soap based and synthetic or syndets bar
Role of Soap based and synthetic or syndets bar
 
Different drug regularity bodies in different countries.
Different drug regularity bodies in different countries.Different drug regularity bodies in different countries.
Different drug regularity bodies in different countries.
 
American College of physicians ACP high value care recommendations in rheumat...
American College of physicians ACP high value care recommendations in rheumat...American College of physicians ACP high value care recommendations in rheumat...
American College of physicians ACP high value care recommendations in rheumat...
 
Male Infertility Panel Discussion by Dr Sujoy Dasgupta
Male Infertility Panel Discussion by Dr Sujoy DasguptaMale Infertility Panel Discussion by Dr Sujoy Dasgupta
Male Infertility Panel Discussion by Dr Sujoy Dasgupta
 
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdf
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdfSGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdf
SGK RỐI LOẠN KALI MÁU CỰC KỲ QUAN TRỌNG.pdf
 
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptx
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptxDNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptx
DNA nucleotides Blast in NCBI and Phylogeny using MEGA Xi.pptx
 
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdf
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdfSGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdf
SGK RỐI LOẠN TOAN KIỀM ĐHYHN RẤT HAY VÀ ĐẶC SẮC.pdf
 
CPR.nursingoutlook.pdf , Bsc nursing student
CPR.nursingoutlook.pdf , Bsc nursing studentCPR.nursingoutlook.pdf , Bsc nursing student
CPR.nursingoutlook.pdf , Bsc nursing student
 
MedMatch: Your Health, Our Mission. Pitch deck.
MedMatch: Your Health, Our Mission. Pitch deck.MedMatch: Your Health, Our Mission. Pitch deck.
MedMatch: Your Health, Our Mission. Pitch deck.
 
Neurological history taking (2024) .
Neurological  history  taking  (2024)  .Neurological  history  taking  (2024)  .
Neurological history taking (2024) .
 
blood bank management system project report
blood bank management system project reportblood bank management system project report
blood bank management system project report
 
Red Blood Cells_anemia & polycythemia.pdf
Red Blood Cells_anemia & polycythemia.pdfRed Blood Cells_anemia & polycythemia.pdf
Red Blood Cells_anemia & polycythemia.pdf
 
Physiology of Smooth Muscles -Mechanics of contraction and relaxation
Physiology of Smooth Muscles -Mechanics of contraction and relaxationPhysiology of Smooth Muscles -Mechanics of contraction and relaxation
Physiology of Smooth Muscles -Mechanics of contraction and relaxation
 

Press problems

  • 1. PRESS PROBLEMS Press problems from examination point of view can be classified into two: 1. Problems regarding suitability of the press from force and energy point of view 2. Problems regarding shout height of the press. Kinematically a mechanical press can be viewed as follows: OA= crank length = r. Therefore Stroke Length is given as S = 2 x OA = 2 r L = length of connecting rod. At some angle , the sliding point on the under face of the ram will be at a distance of H from BDC. Since length of the connecting link AB is large compared to length of crank OA, the inclination of AB with respect to the vertical central line can be neglected. i.e. = 0. Thus any force reaction R acting at a point B can be taken as acting at point A as shown. Therefore the torque at point O =T = R x OA sin = F x OA sin = F x r sin 1
  • 2. [F = force exerted by the press which is equal to the resistance experienced by the ram =R] A press is designed to exert defined amount of force at given crank angle . It means main crankshaft is designed keeping in view some value of torque. In other words, torque provided by a press is fixed. T = F * r sin T F r sin 1 F sin Where ‘r’ is fixed for a particular operation and dependent on the stroke length. Therefore force available from press varies with crank angle. F is minimum when 90 and theoretically infinite when 0 or 180 i.e. at dead ends. 2
  • 3. Though press is capable of exerting infinite force at dead ends, press members such as cranks and connecting links cannot be designed for infinite load. They have to be designed for finite force. This safe finite force is to be determined by the dimensions, strength and allowable deflections of press components such as press frame, connecting link, crank etc. This safe value is known as press capacity and specified as tonnage at crank angle. Let us say press of 63T at 20  . Daylight: The maximum clear distance between the two pressing surfaces of a press when surfaces are in the usable open position. When a bolster plate is supplied it is considered as the pressing surface. The velocity of ram can be computed using following formula: N S Sin S V 0.105 N h ( 1) 60 h where N = Number of strokes per minute (SPM), h = slide location above ( or before) BDC S = stroke, = crank angle Shut height: For a press, the distance from the top of the bed to the bottom of the slide with the stroke down and adjustment up. In general, it is the maximum die height that can be accommodated for normal operation, taking the bolster plate into consideration. Shut height is always measured at BDC. There are two shut heights maximum and minimum 3
  • 4. Position (1) = position corresponding to maximum stroke where Smax= 2 x r1 Position(2) = position corresponding to minimum stroke where Smin = 2 * r2 r1 r2 = (Smax Smin)/2 maximum stroke minimum stroke Thus, MaxDLH = MinDLH + Press Adjustment + 2 If maximum DLH for a given stroke length, which lies between minimum and maximum stroke length, is to be found following formulation can be used. max stroke min stroke Max DLH stroke = Max DLH 2 DLH STROKE STROKE LENGTH PRESS POSITION ADJUSTMENT MAXIMUM TDC MAXIMUM UP MINIMUM TDC MINIMUM DOWN ENERGY OVERLOADING: The energy needed for cutting and forming operations during each stroke is supplied by flywheel which slows down to a permissible percentage, usually 10 20% of its idle speed. For example, if 10% slow down is permissible N1 (N0 N1)/N0 = 0.1, which gives 0 .9 . N0 Total energy of the flywheel I 2 I * 2 N2 E FT = (constant) * N2 = K N2 2 2 2 60 Where N0 = idle flywheel rpm N1 = flywheel rpm after stroke N = flywheel rpm I = M.I. of the flywheel = angular velocity 4
  • 5. The total energy supplied (ES) by flywheel includes energy required to overcome friction and elastic deflections. The electric motor must restore its ideal speed before stroke. The time available between two strokes depends on type of operation (namely) whether it is continuous or intermittent. In continuous type of operation, permissible slowdown is 10% and in discontinuous 20%. I * 2 N1 2 The energy after stroke = 2 60 2 2 2 ES = EFT(N0) EFT(N1) = K N 0 N1 2 2 2 ES K( N 0 N1 ) N1 1 E FT 2 2 K( N 0 ) N0 N1 With a slowdown of 20% = 0.8 N0 ES 1 0.8 2 0.36 E FT This energy supplied must be more than the required energy. Shut heights for the press Shut Height Stroke Position Stroke Press Adjustment Maximum BDC Maximum UP Minimum BDC Minimum DOWN 5
  • 6. Problem 1: A press has a maximum DLH (day light height) of 500 mm and a ram adjustment of 60 mm. Calculate maximum and minimum shut height value for a press tooling if the bolster plat provided on the press bed has a thickness of 80 mm. The press has a variable stoke with maximum stroke and minimum stroke of150 mm and 10 mm respectively. Solution Minimum Shut Height = Maximum DLH Maximum Stroke Press Adjustment (In case of max DLH, press adjustment is UP but in case of minimum shut height, if is down). Minimum Shut Height = 500 150 60 = 290 mm Maximum Shut Height = minimum shut height (SH) + press adjustment + Max stroke Min stroke 2 (150 10 ) = 290 + 60 + = 420 mm 2 To calculate shut height for a tooling, thickness of bolster plates must be deducted from press shut heights. Max SH for die = 420 80 = 340 mm Min SH for die = 290 80 = 210 mm 6
  • 7. Problem 2: A press has minimum DLH 325 mm and Adjustment of ram is 75 mm. Stroke is variable and can be varied from 12.5 mm to 100 mm. If the bolster plate provided has a thickness of 80 mm, calculate maximum and minimum shut height for a die. Solution Maximum DLH = minimum DLH + (r1 r2) + P.A. (press adjustment) 100 12 .5 = 325 75 = 443.75 mm 2 Minimum shut height = Max DLH Max Stroke press adjustment = 443.75 100 75 = 268.75 mm max stroke min stroke Maximum shut height = minimum shut height + PA + 2 = 268.75 + 75 + 43.75 = 387.5 mm Max shut height for tooling = 387.5 bolster plate thickness (= 80 mm) = 387.5 80 = 307.5 mm Min shut height for tooling = 268.75 80 = 188.75 mm Problem 3: A press has maximum DLH 500 mm and a ram adjustment of 60 mm. Stroke can be varied from 10 mm to 150 mm. Calculate minimum and maximum shut height for a press tool for stroke of 100 mm and bolster plate thickness of 80 mm. Solution: First it is necessary to calculate max DLH for stroke length equal to 100 mm as maximum DLH given (500 mm) corresponds to maximum stroke of 150 mm stroke. max stroke(r1 ) given stroke(r ) (150 100 ) = MaxDLH = 500 = 475 mm 2 2 Min shut height of press = max DLH stroke PA (since PA is up in case of max DLH but down in case of min SH) = 475 100 60 = 315 mm Max SH of press = Min SH + PA = 315 + 60 = 375 mm 7
  • 8. OR Max SH of press = Max DLH100 Stroke = 475 100 =375 mm Min SH of press = Max SH PA = 375 60= 315 mm Max Shut height for die = Max SH for press bolster plate thickness = 375 80 = 295 mm Min shut height for die = Min SH for press bolsters plate thickness = 315 80 = 235 mm Problem 4: A press has minimum of DLH 325 mm and press adjustment of slide of 75 mm. Stroke can be varied from 12.5 mm to 100 mm. Bolster plate thickness is 75 mm. Calculate permitted shut height for die if stroke is fixed at 50 mm. Solution Given stroke min stroke Minimum DLH for 50 mm stroke = min DLH (for 12.5 mm stroke) + 2 (50 12 .5) = 325 = 343.75 mm 2 8
  • 9. Minimum shut height of the press = min DLH (for 50 mm stroke) stroke = 343.75 50 =293.75 mm Maximum SH of the press = min SH + PA = 293.75 + 75 = 368.75 mm Maximum SH for the die = max SH for press bolster plate thickness = 368.75 75= 293.75 mm Minimum SH for the die = min SH for press bolster plate thickness = 293.75 75 = 218.75 mm Problem 5: A press is designed to offer 90 ton of force at 20  crank angle with a stroke of 15 cm. Stroke is variable from 1 cm to 15 cm. Calculate tonnage available when ram is 3 cm above its BDC. Take stroke length equal to 10 cm. Solution Given h = 3 cm, s = 10 cm. h 1 cos Where = crank angle from BDC s 2 3 1 Cos 10 2 => 66 .42  As we know that s T = F x r x sin = F* * sin = constant 2 s s => T F * 1 * sin 1 = F2 * 2 * sin 2 1 2 2 F1 = force available 90T at crank angle 1 20 and stroke s1 = 15 cm. F2 = force available at 3 cm above BDC and stroke s2 = 10 cm, 66.42 15 10 90 * * sin(20  ) F2 * * sin(66 .42  ) 2 2 =>F2 = 50.4T i.e. tonnage available when ram is 3 cm above the BDC is 50.4T Problem 6: Check regarding the suitability of the press with following press data for blanking and drawing operation with combination die.  Capacity of the press tool is 150 T at 20 from BDC Stroke length=120mm Total fly wheel energy = 180T cm Permitted slowdown of speed = 20% Blanking load = 30T Drawing force = 10T Blank holding force = 3T Depth of cup = 35 mm = 3.5 cm Stock thickness = 1 mm = 0.1 cm Percent Penetration = 30% 9
  • 10. Solution: I. Suitability of press from tonnage point of view: Total load on the press = blanking load + drawing load + blank holding force = 40 + 10 + 3 = 53 T Since depth of drawn cup is 3.5 cm, drawing will commence at height of 3.5 cm from BDC assuming bottom edge of the cup is at BDC. Further, force increases towards the BDC. Now, we will determine tonnage available at a height of 3.5 cm. h = 3.5 cm, assuming stroke = 12 cm. h 1 cos S 2 3.5 1 cos gives = 65.37 12 2 Since torque transmitted by crank shaft is constant, S1 S2 T F1 sin 1 F2 sin 2 2 2 As stroke length is unchanged, S1 S2 F2 sin 2 F1 sin 1 F2 sin (65.4 ) 150 sin (20 ) F2 56 .44 T Conclusion: As available tonnage F2 is greater than the required tonnage (53T), the given press is suitable to carry out the given operations from tonnage point of view. II. Suitability of the press from the energy point of view Total energy required = Energy for blanking + Energy for drawing + Energy for blank holding Energy required for blanking = Force x distance = F x K x t = 40 x 0.3 x 0.1 = 1.2T.cm Energy required for drawing = Force x distance (= cup depth) = 10 x 3.5 = 35 T. cm Energy for blank holding = Blank holding force x distance (= cup depth) = 3 x 3.5 = 10.5 T.cm Total energy required = 1.2 + 35 + 10.5 = 46.7 T. cm 10
  • 11. Energy available from the flywheel: Permitted slowdown of speed = 0.2 N0 N1 N1 0.2 gives 0.8 N0 N0 Energy supplied (ES ) 2 N1 We know that, 1 1 (0.8) 2 Total energy of the flywheel(E FT ) 2 N0 ES = 0.36 E FT ES E FT * 0.36 = 64.8 T. cm Conclusion: Since the energy supplied (64.8 T. cm) is more than energy required (46.7T.cm); the press is suitable from energy point of view. Thus, the press is suitable from both tonnage and energy point of view. Problem 7: Tonnage rating of a given press is 160 T at 20 crank angle from BDC. Stroke is variable from 10 mm to 120 mm in steps of 10 mm. The ram can be adjusted by 100 mm. Maximum DLH of the press is 500 mm. Total energy of the flywheel is 180T.cm.Permissible slowdown in speed is 20%. If it is decided to use stroke of 100 mm, calculate 1. The maximum and minimum shut height for a combination die. 2. Tonnage available at 25 mm from BDC. 3. Check the suitability of press for following operation: Blanking and drawing with the help of combination die. Blanking load is 45T. Drawing force is 10T. Blank holding force is 3T. Cup depth is 20 mm. Stock thickness is 1.5 mm. Percent penetration is 30%. Solution (i) Maximum DLH at 120 mm (max stroke) is equal to 500 mm. Therefore, it is necessary to find the max DLH at 100 mm stroke. (Max stroke given strok) Max DLH at 100 mm stroke = max DLH at 120 mm stroke 2 11
  • 12. (120 100) = 500 = 490mm 2 Maximum SH of the press = Max DLH at 100 m stroke - stroke = 490 100 = 390 mm Minimum SH of the press = Max SH press adjustment= 390 100 = 290 mm Since there is no mention of bolster plate, we may assume bolster plate thickness of 60mm. Maximum shut height of combination die is =390-60= 330mm Minimum shut height of combination die is =290-60= 230mm (ii) Suitability of the press from the tonnage point of view Determining force availability at height of 25 mm from BDC h= 25 mm = 2.5 cm, S = 100 mm = 10 cm h 1 cos 2 S 2 2 .5 1 cos 2 10 2 2 60 S1 S2 T F1 sin 1 F2 sin 2 2 2 F1 160 T, 1 20 , S1 12 cm F2 = ? 2 = 60 , S 2 = 10 cm Since max tonnage is available at max tonnage 12 10 160 sin (20 ) F2 sin (60 ) 2 2 F2 75 .8 T i.e. Force offered by the press at a height of 25 mm from BDC. Height of the cup is 20 m and total force required for blanking and drawing is 58 T (45 + 10 + 3). As force at height of 25 mm from BDC is greater than the required, force at 20 mm from BDC must be far greater than required (58 T). Hence, the given press is suitable to carry out given operations from tonnage point of view. 12
  • 13. Suitability of the press from the energy point of view Total energy required = blanking + drawing + blank holding = (force x K x t 0 ) + (drawing load x depth of cup)+ (Blank holding force * depth of cup) = (45 * 0.33 * 0.15) + (10 * 2) + (3 * 2) = 28.23 T. cm Energy supplied by the flywheel when permitted slowdown is 20%…. N N1 1 0.2 that gives 0.8 N0 N0 Energy supplied (E S ) 2 N1 1 1 (0.8) 2 Total energy of the flywheel(E FT ) 2 N0 ES 0.36 E FT ES EFT 0.36 = 180 x 0.36 = 64.8 T.cm Energy supplied by the flywheel (64.8 T.cm) is substantially more than required for the operation (28.23 T.cm). The press is suitable from the energy point of view. In sum, the given press is suitable to carry out given operations from tonnage as well as energy point of view. Problem 8: The punch force required for a cup drawing operation is 10 T. Depth of the cup is 35 mm. An air operated blank holder provides a force of 3 T to prevent wrinkling. A 45 T capacity press having total flywheel energy = 33 T. cm is available for use. Another press of capacity 150 T and flywheel energy 180 T. cm is also available. Permissible slowdown of speed is 20%. Calculate total energy required and select a press. Solution Total tonnage required to draw the cup =10+3=13 Ton Energy required for cup drawing = Force x depth of cup = (10 + 3) x 3.5 = 45.5 T.cm First press is unsuitable to carry out the operation from energy point of view. 13
  • 14. N1 0.8 From given data N0 Energy supplied (ES ) 2 N1 1 1 (0.8) 2 =0.36 Total energy of the flywheel(E FT ) 2 N0 Energy Available from the second Press ES EFT 0.36 = 180 x 0.36 = 64.8 T. cm The available energy from the second press is more than the energy required for the operation and therefore this press is suitable for the operation from energy point of view and can be selected. Problem 9: A press is designed for giving 120 t at 30 crank from BDC, when stroke is 20 cm. Prepare a monograph from BDC. From the monograph explain: 1. Overloading of torque without overloading capacity. 2. Overloading of capacity without overloading of torque. Solution: We know that S h= r r cos = (1 cos ) 2 h (1 cos ) s 2 Torque provided by a press remains constant 14
  • 15. S 2T T F sin which gives F ………….(1) 2 S sin In given press T is equal to 20 T 120 sin (30 ) = 600 T. cm 2 2 600 60 F = = …………………………………………(2) 20 sin sin For equation (1) and (2), common variable is 0 30 45 60 75 90 120 150 180 F 120 85 69 62 60 69 120 h/s 0 0.07 0.15 0.25 0.37 0.5 0.75 0.93 1.0 A graph can be drawn to show up the relationship. 1. Overloading of torque without overloading capacity Press will get overloaded if load requirement is more than 120 T. Any point above ZZ means overloading of press and press members will fail. One may select any point on any line like A1 where press will be under loaded. Any point on curve like A2 will have torque equal to that available on the press i.e. 3 600Tcm. Select any point A at = 60 and load equal to F = 80T which is less than rated capacity of 120 T meaning that it is under loaded. S 20 T F sin 80 sin (60 ) 2 2 = 692.8 T. cm which is greater than available torque (600 T.cm) Thus, at the point A3 there is overloading of torque without overloading the capacity. Any point between A 1 to A 2 will not cause overloading of torque and obliviously not causing overloading. Take F = 80T, and = 45 , S 20 T = F sin 80 sin (45 ) = 565.68 T.cm 2 2 15
  • 16. 2. Overloading of capacity without overloading torque Take point B where F = 140 T and = 15 Since the load is more than 120 T, the press is overloaded S 20 T F sin 140 sin (15 ) = 362.34 T. cm (less than 600T cm.) 2 2 This is the case of overloading press capacity (F = 140 T beyond 120 T) without overloading the torque. 16