1. Installation of brass pipe. List of installation tools
According to statistics, brass pipes take a leading position in the premium segment of the class. The
popularity of brass pipes due to their unique operating characteristics, including, for example, the
ability to withstand extremely high pressure and temperature, excellent antibacterial properties.
Professionals provide the following information: it turns out, a brass pipe under certain technological
requirements maintains coolant temperature to 600 ° C and the pressure to 40 atmospheres. If brass
pipes placed in a special envelope (corrugated pipe insulation material) in order to protect them from
damage due to temperature fluctuations coolant pipes can even be placed in a solid wall or floor.
Naturally, as with any other material, the brass pipe is not only attractive advantages, but also
disadvantages. If brass pipes are not used for water supply, and for the heating system should take into
account the possible galvanic processes. For this reason, combined with the brass pipe is not
recommended to use aluminum radiators. When steel radiators selection in their favor can be made
only in the case of a closed system.
Important properties of brass
Brass is known for its versatility of application - in this sense, the material is almost no real
competition. A variety of pipes and fittings made of brass are now used for different types of
engineering services, from plumbing or heating systems to supply fuel for air conditioning or
refrigeration.
2. Manufacturers offer their customers a wide enough selection of brass pipe nipples
(http://www.pexuniverse.com/store/category/brass-pipe-nipples) and brass fittings of different
standards, thus providing the possibility of any project or water heating system.
Brass pipes are known for their exceptional reliability. Proof of this is, for example, the fact that to date
the pipe of a material widely used in the brake systems of vehicles, aircraft hydraulics.
Opt for brass products usually do all who care about the environment. The fact that brass is in contrast
to many other materials used today can be almost completely subjected to recycling. Some studies
indicate that the Earth is still used about 80% of all brass ever mined on the planet.
There is another point that distinguishes brass from other materials used today. It is easily treatable at
any temperature, in fact when the temperature performance of its ductility and strength, on the contrary,
increased. brass at a temperature of 100 ° C allows the pressure in the pipes from 27 to 299
atmospheres, which not fear multiple cycles freeze / thawing the pipe. Such strong thermal stress of all
the materials used for the installation of utilities, in addition to brass can withstand only the highest
grade stainless steel.
Brass is characterized by maximum durability. Once mounted brass pipes will last as long as the
building itself. For this reason, brass may also be called, cost effective material: based on the
perspective of brass pipes are not as expensive as it may seem at first glance.
In addition, to overpay for their safety and health is not possible, at this point, any amount will be
appropriate. brass pipes are made of natural material, which for thousands of years used by man for
making vessels for drinking and other household utensils. Installation of water from brass nipples and
fittings allows for extremely harmless supply of drinking water at home.
Brass pipe nipples popularity: You can see state
where brass pipe nipples most popular. Texas,
California and New York.
3. Brass pipe
Professionals consider the brass pipes is very comfortable to use, because they are very easy to cut and
bend. As for the connection technology of brass fittings and brass pipe nipples, it is also not extremely
difficult.
To date, the most widely used method such as brass pipe capillary high temperature spike. The
technology is based on the so-called capillary effect: while maintaining a certain distance between the
wall surface of the liquid in a capillary rises, overcoming the force of gravity. This effect makes it
possible to solder spread evenly all the pipe, regardless of where it is served. By the way, the solder is
recommended silver-bronze, not lead. Solder is used solid, available in bars with the cross section of 2
mm.
Alternative technologies - the use of press-fitting. This technology is less common, caused by the
higher cost of press-fitting and their ability to keep the pressure only up to 10 atmospheres. Crimping
or clamping ring fittings are more expensive, because of what used to brass pipe is extremely rare.
brass pipe easily handled and applied to any construction site. They allow you to bend around corners,
holes and any other of the obstacles encountered. These materials can be used equally well in both old
buildings and new buildings. brass pipe is a very limited amount of time and does not cause any
difficulty.
Before starting the installation of pipes directly to the pipe diameter to make a calculation, chart the
layout, in other words, to prepare a draft. In accordance with the project in the next phase in the walls
or floor made cutting grooves and arranged openings.
For heating and soldering brass pipe, usually used small size gas post-efficient gas consumption and the
high mobility.
4. Immediately prior to the soldering process at the junction of the brass pipe nipple and apply a special
flux tubes intended for brazing.
To perform the necessary bends used for brass pipe bender. So-called soft brass pipe bend very easily,
but the firm is required to prepare at first, warm place to fold and chill air. Pipe bends are made to
minimize the number of connections to avoid unnecessary resistance to the current of water, reduce the
number of performances of taps.
In the process of soldering pipe and nipple well in a warm place, then soldered burner with solder.
Solder penetrates the junction, completely filling all its capillary space.
Once the pipeline is made soldering, brass pipes are laid in a prepared cutting grooves . Recommended
piping should be insulated to prevent abrasive grinding wall brass tubes for thermal changes.
The final step in the case of installation of heating system - mount the radiator. Again, that use
aluminum radiators in this case it is not recommended, it is better to choose cast iron, steel or bi-metal.
3/4" x 6"
Brass Pipe
Nipple
1/2" x 2-
1/2" Brass
Pipe Nipple
1" x 2"
Brass Pipe
Nipple
1/2" x 3"
Brass Pipe
Nipple
1" x 4" Brass
Pipe Nipple
Mueller
Merit
Trenton
Matco Norca
Webstone
1/2" x 3-1/2"
Brass Pipe
Nipple
1" x 2" Brass
Pipe Nipple
1" x 6" Brass
Pipe Nipple
3/4" x 2"
Brass Pipe
Nipple
1/2" x 2"
Brass Pipe
Nipple
3/4" x 2-1/2"
Brass Pipe
Nipple
1" x Close
Brass Pipe
Nipple
1/2" x 2"
Brass Pipe
Nipple
1/2" x 4"
Brass Pipe
Nipple
Mueller
Merit
Trenton
Matco Norca
Webstone
1-1/4" x
Close Brass
Pipe Nipple
Matco
Norca
Matco
Norca
Mueller
Merit
Trenton
Matco Norca
Webstone
3/4" x 3"
Brass Pipe
Nipplec
1-1/4" x 2"
Brass Pipe
Nipple
1-1/4" x
Close Brass
Pipe Nipple
Merit
Trenton
Matco Norca
Merit
Trenton
Matco Norca
1" x 3" Brass
Pipe Nipple
Matco Norca
Webstone
Matco Norca
Webstone
Matco Norca
Webstone
Matco Norca
Webstone
3/4" x 4"
Brass Pipe
1" x 2-1/2"
Brass Pipe
Merit
Trenton
1/2" x Close
Brass Pipe
3/4" x 1-1/2"
Brass Pipe
5. Nipple Nipple Matco Norca Nipple Nipple
1-1/4" x 2"
Brass Pipe
Nipple
3/4" x 6"
Brass Pipe
Nipple
Matco Norca
Webstone
3/4" x 3-1/2"
Brass Pipe
Nipple
1/2" x 1-1/2"
Brass Pipe
Nipple
3/4" x Close
Brass Pipe
Nipple
Merit
Trenton
Matco Norca
1" x 3" Brass
Pipe Nipple
Matco Norca
Webstone
Mueller
Merit
Trenton
Matco Norca
Webstone
3/4" x 3-1/2"
Brass Pipe
Nipple
Merit
Trenton
Matco Norca
Mueller
Merit
Trenton
Matco Norca
Webstone
1/2" x 6"
Brass Pipe
Nipple
1" x 2-1/2"
Brass Pipe
Nipple
1/2" x 6"
Brass Pipe
Nipple
3/4" x 4"
Brass Pipe
Nipple
3/4" x Close
Brass Pipe
Nipple
3/4" x 3"
Brass Pipe
Nipple
1/2" x 5"
Brass Pipe
Nipple
1" x Close
Brass Pipe
Nipple
Literature:
www2.itap.purdue.edu/msds/docs/3843.pdf
www.colorado.edu/gsearch/all/brass%20pipe%20fittings
http://codes.ohio.gov/oac/4101%3A2-12-01