DtiCorp.com Is Introducing 8 Honeywell C7061 Flame Sensors Honeywell C7061 - Dynamic self-checking flame detector used with R7861 Dynamic Self-check Amplifiers for sensing the ultraviolet radiation generated by the combustion of gas, oil, or other fuels. Fort Lauderdale, FL - Popular Honeywell online retailer DtiCorp.com (http://www.DtiCorp.com) is introducing 8 Brand New Honeywell C7061 Flame Sensors. Dynamic self-checking flame detector used with R7861 Dynamic Self-check Amplifiers for sensing the ultraviolet radiation generated by the combustion of gas, oil, or other fuels. The C7061A is a dynamic self-checking flame detector for sensing the ultraviolet radiation generated by the combustion of gas, oil, or other fuels. This flame detector is available in two versions: model C7061A for use in Standard applications, and model C7061F for use in installations requiring explosion-proof packaging. The flame detector is designed for use with either, R7061 Dynamic Self-Check Ultraviolet amplifier and R4348 Flame Switch or R7861A Dynamic Self-Check Ultraviolet amplifier and 7800 SERIES Burner Programmers. These configurations provide a closed-loop, self-checking circuit which insures the integrity of both amplifier and flame detector. Improper response simulated flame loss results in a safety shutdown and/or alarm. Features: - Oscillating shutter interrupts ultraviolet radiation reaching the UV sensor to provide the UV sensor tube checking function. - Can be mounted horizontally, vertically or at any angle in between. - The detector requires faceplate alignment and has integral locating reference points to assure proper operation of the shutter mechanism. - Field replaceable ultraviolet sensing tube and quartz viewing window. - Models with threaded conduit fitting and color-coded leadwires allow rapid electrical installation. - C7061A1038 or A1046 5 pin Brad Harrison type (formally 41307N) mating connector not supplied nor available through Honeywell. - Two detectors can be wired in parallel to reduce nuisance shutdowns in difficult flame sighting applications. - Protective heat block built into mounting flange. - Minus 40 F (-40 C) rated ultraviolet sensing tube is supplied. - C7061E meets NEMA 4 standards with viewing window rated to 20 psi. - C7061F has an explosion-proof housing for use in hazardous atmospheres with a viewing window rated to 100 psi. Specifications: - Models C7061A: Self checking UV flame detector in standard housing. C7061F: Self checking UV flame detector in explosion proof housing. Designed for use with either R7061 Dynamic Self-Check Ultraviolet amplifier and R4348 Flame Switch or with R7861A Dynamic Self-Check Ultraviolet amplifier and 7800 SERIES Burner Programmers - Ambient Operating temperature ratings C7061A: -40°C to +70°C (-40°F to +160°F)“(derate ambient 1°F for every 13°F of aspirator temperature over 160°F). C7061F: -20°C to +70°C (-22°F to +160°F) - Storage temperature ratings: Minus 51°C to +85°C (-60°F to +185°F) - Voltage and Frequency: C7061A1004 120 VAC, 50/60 Hz C7061A1020 115/230 VAC, 50/60 Hz C7061F1003 115/230 VAC, 50/60 Hz The System operates correctly at a nominal voltage (-15%, +10%), 50/60 Hz. - Flame Signal: Measured at the flame current meter jack. C7061 Detector: 1.4 to 5.5 micro amps (nominal). R7061A Amplifier: 2.5 to 5.5 micro amps (nominal). R7861A Amplifier: 1.25 to 5.0 Volts (On keyboard display module). - Flame Signal amplifier: R7061A Dynamic Self-Check Ultraviolet amplifier R7861A Dynamic Self-Check Ultraviolet amplifier - Interchangeability: Models C7061A and C7061F are not interchangeable with other flame detector models. - Shutter frequency: 0.2 Hz, nominal (when used in combination with 7800 SERIE). Interrupts the line-of-sight of the detector about 12 times per minute to provide self-checking. Any malfunction in the flame detection system results in a safety shutdown.