1. http://designforeveryone.howest.be/

2. FREDBRIL 3.4.4
€ 114 Approximately 1 hour
http://prismabril2011.blogspot.com// Jeff Stubbe / Joris Bellens
http://designforeveryone.howest.be/

3. ASSEMBLY MANUAL
http://designforeveryone.howest.be/

4. FREDBRIL 3.4.4
BILL OF MATERIAL
- 3D printed frame (€50)
- Leather legs (€10)
- Magnets (€10,90)
- Prisms (€34)
- VW_1 XBPT Shrink tube with glue (€2,5)
- Lighter
- Sewing kit
Scissors – Sewing kit- Lighter
Shrinking sock - Prisms
Leather legs - 3D printed frame

5. 1
FREDBRIL 3.4.4
PRINT out the measuring tool template
which is donwloadable at
http://prismabril2011.blogspot.com/. This tool
will help you to measure the distance between
your eyes. Follow the instructions on the
template.
After succesfuly measuring the distance
between your eyes, contact IDC (Industrial
Design Center). lieven.de.couvreur@howest.be
Measuring tool
10 Minutes
Printer - Scissors - Glue - Box of corn flakes
0,05 for printing the tool

6. 2
2
FREDBRIL 3.4.4
AFTER A few weeks you will receive a
package that includes a personalized frame,
based on the distance between your eyes, and
leather legs. These leather legs will be
personalized by engraving your name.
2 Minutes
Scissors or knife
Printed frame – Leather legs
50 + 10 + 5

7. 3
FREDBRIL 3.4.4
STITCH the leather legs so they form a
little back to put the magnets in.
Choose a color you like to personalize it.
15 min
Sewing kit
Sewing kit
0

8. 4
4
FREDBRIL 3.4.4
PUSH four magnets in each leather bag
with a small screw driver unitll they have a tight
fit.
30 seconds
Little tool to push
Magnets
1,76

9. 5
5
FREDBRIL 3.4.4
GLUE the leather legs to the printed frame
with contact glue. To ensure the strength, stitch
an X through the holes in the leather and the
frame. Put the frame away untill the glue is dry.
(±24 hours)
10 minutes to glue and stich - 24 hours to dry
Sewing kit - Glue
Glue

10. 6
6
FREDBRIL 3.4.4
REMOVE the two prisms from the
original frame, by sliding a thin knife under the
prisms. Now put them in the printed frame
without any glue. Normally the friction between
the prisms and the frame is enough to hold
them.
1 minute
Prism glasses (http://www.medesign.co.uk)
2 prisms
34

11. 7
7
FREDBRIL 3.4.4
CUT a piece of shrink tube (2 x 25mm) and
put slide them over the legs of your glasses. If
needed detach the legs.
Slide two magnets in between the outer side of
the legs and the shrinking tube. Make sure to
check the polarity of the magnets so they attrack
the magnets inside the leather legs.
Hold a lighter to the tubes to shrink them, while
heated the tubes will release a glue that will fix
the magnets to the legs of the glasses.
Note: The glue inside the shrinking tubes is easy
removable . There is no risk of damaging your
glasses.
5 Minutes
Lighter
Shrinking tube- Magnets
4 Magnets – 2 pieces of shrinking tube
2,5

12. TECHNICAL ADDENDUM
http://designforeveryone.howest.be/

15. TEAM CONTACTS
http://designforeveryone.howest.be/

16. JEFF@GMAIL.COM
TEL +32474 60 27 13
INFO@JORISBELLENS.BE
TEL +32494 64 48 16
ERGOMENEN@HHR.BE
TEL +3256 52 20 27
FDERONNE@HHR.BE
TEL +32476 43 96 87
http://designforeveryone.howest.be/