Virtual firewalls, also known as security contexts, allow a single Cisco ASA device to act as multiple independent firewalls. This document discusses how to configure multiple security contexts on a Cisco ASA. It describes allocating interfaces and resources to unique contexts for separate network segments or customers. The admin context manages the entire ASA device and is used to create other contexts. Features like routing and VPN are unavailable in multiple context mode.

1. How to Configure Cisco ASA Virtual Firewall?
Device virtualization is one of the most popular topics in IT industry today and Cisco
has been supporting this concept in the majority of its network devices. Now we will
talk about Cisco ASA virtualization, which means multiple virtual firewalls on the
same physical ASA chassis. Virtual ASA is also known as “Security Context”.
All Cisco firewall models (except ASA 5505) support multiple security contexts (i.e
virtual firewalls). By default, all models support 2 security contexts without a license
upgrade (except the Cisco ASA 5510 which requires the security plus license).
Each Context has its own configuration file and security policy, i.e. one context is
completely isolated and does not depend on other contexts. The exception is the
Admin Context, from which the whole ASA appliance (physical ASA) is managed and
also is used to create the other Contexts. For enabling the creation of virtual contexts
on the ASA appliance, we must switch to Multiple Context mode. In this mode some
features are not available, like Dynamic Routing, IPSEC and SSL VPN, Multicast and
Threat Detection. Let’s make a little discussion when multiple context mode is
advisable and when it is not.
When would you want to use multiple security contexts?
●If you want to use the active/active failover feature. Keep in mind that with
active/active failover, you should not use more than half of the available bandwidth.
●If you are an ISP and need to offer a different security context for each customer.
● If you need to provide different security policies for various departments, users, or
vendors and need to create a separate context for each one.
● If you’d like to reduce hardware requirements by combining the functionality of
multiple firewalls into one.
When should you not use multiple security contexts?
● If you need to provide VPN services such as remote access or site-to-site VPN
tunnels.
● If you need to use dynamic routing protocols. With multiple context mode, you can
use only static routes.
● If you need to use QoS.
● If you need to support multicast routing.
● If you need to provide Threat Detection.
Now let’s consider an example of how Contexts are configured. In the scenario in our
topology below, we have one ASA appliance and let’s create two contexts for two
customers and one admin context for ASA appliance management.
Physical Topology Diagram:
http://www.router-switch.com/页 1

2. Logical Topology Diagram:
http://www.router-switch.com/页 2

3. Equipment Used in this LAB
ASA 5520 – Cisco Adaptive Security Appliance Software Version 8.0(3)
Catalyst 2960 – LAN Lite IOS.
Before starting configuration let’s check if it works in Single context mode or multiple
context mode. As I’ve already stated, ASA appliance must be in multiple context
mode for creating Security contexts.
!Verify ASA Operating mode.
asa # show mode
Security context mode: single
! enable multiple mode, for switching to this Mode, restart is required.
asa(config)#mode multiple
Then the following output is displayed. ASA Appliance converts the current running
configuration into two files: a new startup configuration that comprises the system
configuration, and “admin.cfg” that comprises the admin context (stored in the root
directory of the internal Flash memory). The original running configuration is saved
as “old_running.cfg” (in the root directory of the internal Flash memory).
WARNING: This command will change the behavior of the device
WARNING: This command will initiate a Reboot
http://www.router-switch.com/页 3

4. Proceed with change mode? [confirm]
Convert the system configuration? [confirm]
!
The old running configuration file will be written to flash
The admin context configuration will be written to flash
The new running configuration file was written to flash
Security context mode: multiple
***
*** — SHUTDOWN NOW —
***
*** Message to all terminals:
***
*** change mode
Rebooting….
Booting system, please wait…
!after rebooting verify ASA Operation mode
asa# show mode
Security context mode: multiple
After restarting let’s start configuration of Contexts. First configure the admin
context.
!Configure the admin context
asa(config)# admin-context admin
asa(config)# context admin
asa(config-ctx)# allocate-interface Management0/0
asa(config-ctx)# config-url disk0:/admin.cfg
!configure the Sub-interfaces for Customer1
interface GigabitEthernet0/1.11
vlan 11
interface GigabitEthernet0/0.21
vlan 21
!configure the Sub-interfaces for Customer2
interface GigabitEthernet0/1.12
vlan 12
interface GigabitEthernet0/0.22
vlan 22
Now we start creating contexts for Customer-1 and Customer-2 and allocate
interfaces.
! Configure the Customer1 context shown as C1 in diagram.
asa(config)# context c1
asa(config-ctx)# allocate-interface gigabitethernet0/0.21
asa(config-ctx)# allocate-interface gigabitethernet0/1.11
asa(config-ctx)# config-url disk0:/c1.cfg
! Configure the Customer2 context shown as C2 in diagram.
http://www.router-switch.com/页 4

5. asa(config)# context c2
asa(config-ctx)# allocate-interface gigabitethernet0/0.22
asa(config-ctx)# allocate-interface gigabitethernet0/1.12
asa(config-ctx)# config-url disk0:/c2.cfg
I will not describe how VLANs on Switches are configured. Let’s consider switching
between Contexts. We can switch to any context from admin context, but we can’t
switch from Customers context to anywhere.
! Let’s log in to Customer1 context. The syntax of command is the following:
changeto context <context name>
asa#changeto context c1
! Let’s switch to system configuration mode. Switching to this mode is available only
from Admin Context. In system configuration mode Contexts are created and
resources are allocated.
asa#changeto system
More Related Cisco Firewall Guides:
Cisco ASA Firewall Licensing
Simple Steps to Connect a Remote Office to Cisco ASA 5510
How to Configure Cisco ASA 5505 Firewall?
http://www.router-switch.com/页 5