Introduction, Hydrologic cycle, Climate and water availability, Water balances,
Precipitation: Forms, Classification, Variability, Measurement, Data analysis, Evaporation and its measurement, Evapotranspiration and its measurement, Penman Monteith method. Infiltration: Factors affection infiltration, Horton’s equation and Green Ampt method.
ICT role in 21st century education and it's challenges.
Introduction, hydrologic cycle, climate and water m1
1. MODULE- I
Introduction, Hydrologic
cycle, Climate and water
availability, Water
balances, Precipitation
Prepared by
Bibhabasu Mohanty
Dept. of Civil Engineering
SALITER, Ahmedabad
2. Content…
Forms, Classification, Variability, Measureme
nt, Data analysis, Evaporation and its
measurement, Evapotranspiration and its
measurement, Penman Monteith method.
Infiltration: Factors affection
infiltration, Horton’s equation and Green Ampt
method.
3. Introduction
• Hydrology deals with the
occurrence, circulation and distribution of
water upon, over and beneath the earth surface.
• Engineering hydrology includes those
segments of the field related to
planning, design, and operation of engineering
projects for the control and use of water.
4. • engineering hydrology deals with -
(1) estimation of water resources
(2) the study of processes such as precipitation,
runoff, Evapotranspiration and their interaction
and
(3) the study of problems such as flood and
draught and strategies to combat them.
5. Applications
• The capacity of storage structures such as
reservoirs
• The magnitude of flood flows to enable safe
disposal of the excess flow.
• The minimum flow and quantity of flow
available at various seasons.
• The interaction of the flood wave and
hydraulic structures, such as
levees, reservoirs, barrages and bridges.
6. Hydrological cycle
• water circulatory system on earth the waters of
the earth, linking atmosphere, land, and
oceans.
• water evaporates from the ocean surface,
driven by energy from the sun, and joins the
atmosphere, moving inland
• Atmospheric conditions act to condense and
precipitate water onto the land surface
7.
8. Elements of hydrological cycle
• Evaporation, E
• Transpiration, T
• Precipitation, P
• Surface runoff, R
• Groundwater flow, G, and,
• Infiltration, I
9. Precipitation
• All forms of water that reach the earth from the
atmosphere is called Precipitation.
• The usual forms are
rainfall, snowfall, frost, hail, dew. Of all
these, the first two contribute significant amounts
of water.
• Rainfall being the predominant form of
precipitation causing stream flow, especially the
flood flow in majority of rivers. Thus, in this
context, rainfall is used synonymously with
precipitation.
10.
11. • In nature water is present in three aggregation
states:
– solid: snow and ice;
– liquid: pure water and solutions;
– gaseous: vapors under different grades of pressure
and saturation
• The water exists in the atmosphere in these
three aggregation states.
12. • Types of precipitation
– Rain, snow, hail, drizzle, glaze, sleet
• Rain:
– Is precipitation in the form of water drops of
size larger than 0.5 mm to 6mm
– The rainfall is classified in to
• Light rain – if intensity is trace to 2.5 mm/h
• Moderate – if intensity is 2.5 mm/hr to 7.5
mm/hr
• Heavy rain – above 7.5 mm/hr
13. • Snow:
– Snow is formed from ice crystal masses, which
usually combine to form flakes
• Hail (violent thunderstorm)
– precipitation in the form of small balls or lumps
usually consisting of concentric layers of clear ice and
compact snow.
– Hail varies from 0.5 to 5 cm in diameter and can be
damaging crops and small buildings.
14. • Sleet - droplets that freeze once entering the
freezing layer of air.
• Drizzle – fine sprinkle of numerous water droplets
of size less than 0.50 mm and intensity less than 1
mm/h.
• Glaze – when rain or drizzle comes in contact
with cold ground at around 0 ˚C, the water drops
freeze to form ice coating called glaze or freezing
rain.
15.
16. Mechanisms for air lifting
1. Frontal lifting
2. Orographic lifting
3. Convective lifting
17. Definitions
• Air mass : A large body of air with similar
temperature and moisture characteristics over its
horizontal extent.
• Front: Boundary between contrasting air masses.
• Cold front: Leading edge of the cold air when it is
advancing towards warm air.
• Warm front: leading edge of the warm air when
advancing towards cold air.
18. Frontal Lifting
• Boundary between air masses with different
properties is called a front
• Cold front occurs when cold air advances towards
warm air
• Warm front occurs when warm air overrides cold air
Cold front (produces cumulus cloud) Cold front (produces stratus cloud)
19. Orographic lifting
Orographic uplift occurs when air is forced to rise because
of the physical presence of elevated land.
20. Convective lifting
Convective precipitation occurs when the air near the
ground is heated by the earth’s warm surface. This
warm air rises, cools and creates precipitation.
Hot earth
surface
21. Precipitation Variation
• Influenced by
– Atmospheric circulation and local factors
• Higher near coastlines
• Seasonal variation – annual oscillations in some
places
• Variables in mountainous areas
• Increases in plains areas
24. Measurement of precipitation
• Precipitation is expressed in terms of depth to
which rainfall water would stand on an area if
all the rain were collected on it.
• Rainfall at a place can be measured by a rain
gauge. The rain gauge may be broadly
• classified into two types.
(1) Non-recording type rain gauge
(2) Recording type rain gauge.
25. Non-recording type rain gauge
• The Symon rain gauge consists of a cylindrical
vessel, called metal casing, of 12.7
• cm diameter, with a base of 21.0cm. The metal
casing is fixed vertically to a masonry
• foundation block of the size 60 cm x 60 cm x
60 cm. A funnel with a circular rim of 12.7 cm
and a glass bottle are placed in the metal
casing.
26. • The height of the metal casing is fixed so that
the rim is 30.5 cm above the ground surface.
• The glass bottle, called the receiver, is of 7.5 to
10 cm diameter. The rain gauge is kept in
open.
• The rain falling into the funnel is collected in
the receiver.
• The receiver, with the rain water in it, is taken
out of the metal casing.
27. • The rainfall depth is measured with a special
measuring glass jar graduated in mm of
rainfall.
• It can measure up to 12.5 mm of rainfall.
• During heavy rains, the rainfall is measured 3
or 4 times in a day.
• The total rainfall of the day is obtained by
adding all the individual measurements of day.
28.
29. Site for a Rain Gauge Station
1. The site should be in an open space having
an area of at least 5.5 m x 5.5 m.
2. The distance of the instrument from the
nearest obstruction should not be less than 30
m or twice the height of the obstruction.
3. A site that is sheltered from high winds
should be chosen.
30. 4. The rain gauge, as far as possible, should not
be installed on the top or the side of the hill. If
unavoidable, the site which is best protected
from high winds should be chosen.
5. A fence should be erected around the rain
gauge station to protect the gauge from
cattle, dogs, etc. However, the distance of the
fence should not be less than twice its height.
6. The gauge must always be mounted firmly so
that it cannot be disturbed even by the
strongest wind in that region.
31. 7. The gauge should be set as near the ground
surface as possible to reduce wind effects. But
at the same time, it should be sufficiently high
to prevent splashing of surface water into it.
8. The gauge should have a level horizontal
catch surface.
32. Recording type rain gauge
• The recording type rain gauges have recording
arrangement, which gives the rainfall
• intensity and the duration of the
rainfall, besides giving the total depth of the
rainfall. These
• rain gauges are, therefore, more useful than the
non-recording type rain gauges
34. Tipping bucket rain gauge
• The tipping bucket rain gauge consists of two small
buckets placed below the funnel fitted in a 30 cm
diameter receiver .
• The buckets are balanced in an unstable equilibrium
about a horizontal axis such that at one time only one
bucket remains below the funnel.
• One bucket is always higher than the other. As the
rainfall is collected by the receiver, it passes through
the funnel to the higher bucket.
35. • After a certain small amount of rainfall
(usually 0.25 mm) is received by the higher
bucket, it becomes unstable and tips to empty
itself into a measuring tube placed below it.
• At the same time, the other bucket comes to
the higher position and starts colleting the
rainfall.
36. • The tipping of the bucket actuates an electric
circuit, which causes a pen to make a mark on
a chart wrapped around a drum revolved by a
clock-driven mechanism.
• Thus each mark on the chart corresponds to a
rainfall of 0.25 mm.
• By counting the number of marks and noting
the time, the intensity and amount of the
rainfall can be determined.
37.
38. Weighing Bucket Rain Gauge
• The rain is collected by a weighing bucket
through a funnel.
• The bucket rests on a weighing platform of a
spring or lever balance attached to a weighing
mechanism.
• As the bucket is filled with rain water, its
weight increases and the weighing platform
moves downwards.
39. • The movement of the weighing platform is
transmitted to a pen through a system of links
and levers.
• The pen makes a trace of the accumulated
amount of rainfall on a chart attached to a
drum revolved by a clock driven mechanism.
• The record is continuous and is in the form of
the conventional mass curve .
40. • The rotation of the drum sets the time scale whereas
the vertical motion of the pen records the cumulative
rainfall.
• The slope of the mass curve at any point gives the
intensity of the rainfall.
41. Float type rain gauge
• In the float-type gauge, the precipitation
falling on the receiver passes through the
funnel and filter and is collected in a float
chamber.
• The filter prevents dust, debris, etc, from
entering the float chamber.
• The float chamber contains a float with a
vertical stem fixed over it.
• A pen is mounted on the top of the vertical
stem.
42.
43. • As the rain is collected in the float
chamber, the float rises and the pen moves on
a chart fixed on a drum revolved by a clock-
driven mechanism.
• The pen thus marks a trace of the cumulative
depth of rainfall on the chart.
• The record is in the form of the conventional
mass curve, from which the intensity and
duration of rainfall can be determined.
44. Preparation of Data
• Before using the rainfall records of a station, it
is necessary to first check the data for
continuity and consistency.
• The continuity of a record may be broken with
missing data due to many reasons such as
damage or fault in a rain gauge during a
period.
• The missing data can be estimated by using the
data of the neighbouring stations.
45. • In these calculations, the normal rainfall is
used as a standard of comparison.
• The normal rainfall is the average value of
rainfall at a particular data, month or year over
a specified 30-year period or so.
• The normal rainfall is updated every ten years.
46. Estimation of missing rainfall data
1. Arithmetic average method
2. Comparison method
3. Normal ratio method
4. Isohyetal map method
47. 1. Arithmetic average method
• If normal annual precipitation at adjacent
stations are within 10% of annual normal
rainfall of the station under consideration, then
the missing rainfall data may be estimated as
simple arithmetic avg. of rainfall at adjacent
rain gauges.
Px = 1/n (P1+P2+----+Pn)
• Px = precipitation at station x
• P1, P2,---Pn = rainfall at surrounding rain
gauges
48. 2. Comparison method
• If the rainfall record of a rain gauge station (say. X) is
missing for a relatively long period, such as a month
or a year, it can be estimated by comparing the mean
annual rainfall of the station X with that of an
adjoining station A.
• where PX and PA are the precipitations of the stations
X and A for the missing period
• NX and NA are the mean annual rainfalls of the
stations X and A.
49. 3. Normal ratio method
• When there is the short break in the
precipitation data of a rain gauge station, it can
be estimated from the observed data of three
adjoining index stations A, B and C, which are
evenly distributed around the station X.
50. • Nx = normal annual rainfall at station X
• NA, NB, --- NM = normal annual rainfalls at n
surrounding rain gauges respectively.
• A minimum 3 surrounding stations are
generally used in normal ratio method.
51. 4. Isohyetal map method
• Isohyets are the contours of equal rainfall depth.
• An isohyetal map is prepared from
• the record of various rain gauge stations by
interpolation.
• The isohyetal map method is suitable for the
estimation of the missing data of a station X due to a
particular storm.
• An isohyetal map is prepared from the data of the
various rain gauge stations, and the precipitation of
the station X is estimated from the two isohyets
between which the station lies.
52. • It consider rainfall characteristics including
average patterns, distance from
sea, topography and storm paths.
• Interpolation of missing data from such maps
reasonably accurate.
53. Average Rainfall Depth Over An Area
• The rainfall recorded by a rain gauge
represents the rainfall at that station.
• It is also called the point rainfall.
• In many hydrological studies, the average
depth of rainfall over a specified area due to a
storm, or due to a number of storms, is
required.
• For determination of the average precipitation
over an area, a large number of rain gauges are
installed.
54. • The average rainfall over the area is found
from the rainfall data of these rain gauges by
one of the following three methods:
1. Arithmetic mean method
2. Thiessen polygon method
3. Isohyetal map method
55. Arithmetic Mean Method
• Simplest method for determining areal average
P1 = 10 mm
P1
P2 = 20 mm
P3 = 30 mm
N
P2
1
P Pi
N i 1
P3
10 20 30
P 20 mm
3
• Gauges must be uniformly distributed.
• Gauge measurements should not vary greatly
about the mean.
56. Thiessen polygon method
P1
• Any point in the watershed
A1
receives the same amount of
P2
rainfall as that at the nearest gage
• Rainfall recorded at a gage can be A2
P3
applied to any point at a distance
halfway to the next station in any A3
direction
57. Steps in Thiessen polygon method
1. Draw lines joining adjacent gages
2. Draw perpendicular bisectors to the lines created in step
1
3. Extend the lines created in step 2 in both directions to
form representative areas for gages
4. Compute representative area for each gage
5. Compute the areal average using the following formula
N
1
P Ai Pi
A i 1
P1 = 10 mm, A1 = 12 Km2
P2 = 20 mm, A2 = 15 Km2
P
12 10 15 20 20 30
20.7 mm P3 = 30 mm, A3 = 20 km2
47
58. Isohyetal method
• Steps
10
– Construct isohyets (rainfall
20
contours) P1
A1=5 , p1 = 5
– Compute area between each A2=18 , p2 = 15
pair of adjacent isohyets (Ai) P2
– Compute average A3=12 , p3 = 25
precipitation for each pair of
adjacent isohyets (pi) P3
30 A4=12 , p3 = 35
– Compute areal average using
the following formula
N
1 5 5 18 15 12 25 12 35
P Ai Pi P 21.6 mm
A i 1 47
59. Presentation of rainfall data
• The rainfall data are usually presented either in
the form of a mass curve or a hyetograph.
(a)Mass Rainfall curve
• The mass rainfall curve is a plot between the
accumulated rainfall at a station against time
as abscissa, plotted in chronological order.
• The recording type rain gauge gives directly
the mass curve.
60. • The mass curve of a non-recording gauge can be
prepared from the knowledge of the beginning
and the end of the storm, and distributing the total
depth of the rainfall over the various periods
according to the mass rainfall curves of the
adjacent recording rain gauge stations.
• However, such a mass curve is approximate.
• The mass curve is useful for the determination of
the intensity, amount, and duration of the rainfall.
• The amount of duration of the rainfall are
obtained directly from the curve.
61. 2.6 Intensity – Duration – Frequency (IDF) Relationship
Mass Curve of Rainfall
Mass curve of rainfall
accumulated precipitation, mm
60
50
40
30 1st storm,
16 mm
20 2nd
storm, 16
10 mm
0
0 20 40 60 80 100 120
Time, hour
62. (b) Hyetograph
• The hyetograph is a bar diagram plotted between the
average intensity of rainfall as ordinate and the time
as abscissa .
• The hyetograph is obtained from the mass rainfall
curve, represented as a bar chat.
• For draw the hyetograph, convenient time interval
chosen and for each time interval corresponding
reading of accumulated rainfall noted from mass
rainfall curve.
• In urban drainage problem small durations used, in
flood flow in larger catchment it is 6 hrs.
63. Hyetograph of a storm
Total depth = 10.6 cm
0.5 Duration = 46 hr
Intensity, cm/hr
0.4
0.3
0.2
0.1
0
0–8 8 – 16 16 – 24 24 – 32 32 – 40 40 – 48
Time, hours
64. Evaporation
• is the processes in which a liquid changes to
the gaseous state at the free surface, below the
boiling point through the transfer of heat
energy.
• This change in state requires an exchange of
585 Cal for each gram of water evaporated.
• expressed as an evaporation rate in mm / d, cm
/ d , in / d.
65.
66. Factors affecting
(a) Meteorological factors
1. Solar radiation - changes depend upon
latitude, season, time of day and sky condition
(cloudiness)
2. air temperature
3. vapour pressure
4. wind velocity
5. atmospheric pressure
67. (b) Nature of evaporating surface
1. vegetation
2. building
3. paved streets
4. soil surface
5. snow / ice
(c) Water quality
1. salinity
2. dissolved solids
68. Measurement
• The amount of water evaporated from a water
surface is estimated by -
1. Using evaporimeter data (pan evaporation)
2. Emperical, equation (Penman's method, etc.)
3. Analytical methods – (water budget
method, energy budget method, etc.)
69. Pan evaporation
U. S. Class A Evaporation pan
• most commonly used evaporation pan.
• the pan consists of a shallow vessel about 1.21 m
in diameter and 25.5cm deep.
• made of unpainted galvanised iron sheet.
• Where there is corrosion problem, it is made of
monel sheet.
• Water in the pan is filled to a depth of 20cm.
• When the depth of water reduces to 18 cm, it is
refilled.
70. • Water surface level is measured daily with a
hook gauge installed in the stilling well.
• The pan is placed on a wooden platform such
that its base is 15 cm above the ground surface
to allow free circulation of air below the pan.
• Evaporation is computed as the difference
between observed water levels on two
consecutive days.
71. • Alternatively, it is computed from the water
added each day to bring the water level up to a
fixed mark in the stilling well.
• While computing evaporation, adjustment
shall be made for any precipitation occurred
during the period.
72. Colorado Sunken Pan
• this type of pan is buried into the ground such
that the water
• level is at the ground level. The pan is 92 cm
square in plan and 46 cm deep. It is made of
• unpainted galvanised iron sheet. The main
advantage of the sunken pan over the Class A
• Evaporation pan is that its radiation and
aerodynamic characteristics are closer to those
of a reservoir
73. • However, it has the following disadvantages:
(i) It is more expensive.
(ii) It is more difficult to detect leaks.
(iii) It needs more care to keep the surrounding
area free from grass, dust, etc.
74. IS Standard Pan
• modified form of the U.S. Class A Evaporation
Pan. The pan consists of a
• shallow vessel made of copper sheet of 0.9mm
thickness, tinned inside and painted outside.
• The pan is 1.22m in diameter and 25.5 cm in
depth.
• installed on a wooden grillage platform 10 cm
above the ground surface.
75. • The pan has small stilling well in which a
fixed point gauge with a vernier is installed to
measure the level of water.
• The water surface is initially kept 5 cm below
the rim (top) of the pan.
• The daily evaporation is computed as the
difference between the observed water levels
in the pan.
76.
77. Water-Budget Method
• based on measurement of continuity of water flow
essentially, the budget comprised by the various items
of input, and water storage of hydrologic system.
• Continuity equation
• E = (S1 - S2) + I + P - O – Os
• where E = evaporation
• S1, S2 = storage at time 1 and 2
• I = surface inflow, P = precipitation
• O = surface outflow Os = subsurface seepage (most
difficult to evaluate)
78. Advantage
• This method is simple in concept.
Disadvantage
• This method is difficult to do so accurately
because of the effects of errors in measuring
various items involved in the water balance.
79. Energy Budget Method
• it deals with the continuity of energy flow
instead of water flow. Use Continuity equation
in energy units
• Q n – Qh - Qe = Q θ - Qv
• where Qn = net radiation absorbed by water body
• Qh = sensible heat transfer to the atmosphere
• Qe = energy used for evaporation
• Qθ = increased in energy stored in water body
• Qv = advected energy (net energy content of inflow
and outflow elements).
80. Advantage
• It has increasing application to special studies.
Disadvantage
• It involves a great deal of instrumentation.
• It cannot readily be used without much data.
81. Transpiration
• process by which water leaves the body of a
living plant and reach the atmosphere as water
vapour.
• water is taken up by the plant-root system and
escape through the leaves.
82. Factors affecting transpiration
1. atmospheric vapour pressure
2. temperature
3. wind
4. light intensity
5. characteristics of plant
- plant type (- shallow rooted species
- deep rooted species).
- available water .
• - density of vegetative cover.
83. Measurement
Phytometer method
• Practical method for measuring transpiration.
• It is a large vessel filled with soil in which one
or more plants are rooted.
• The soil surface is sealed to prevent
evaporation.
• The only escape of moisture is by transpiration
• which can be determined by weighing the plant
and container at desired intervals
84. • Transpiration loss , T = (W1 + W) – W2
• W1 = is initial wt. of instrument
• W2 =final wt. of instrument
• W = total wt. of water added during full
growth of plant
• T = loss due to
evaporation
85. Transpiration ratio
• T.R. = (Total mass of water transpired by plant
during full growth)/ mss of dry matter
produced
• Varies with climate and region
86. Evapotranspiration
• sum of the amount of water transpired by plants
during the growth process and that amount that
is evaporated from soil and vegetation in the
domain occupied by the growing crop.
• ET is normally expressed in mm/day.
87. Factors that affect Evapotranspiration
Weather parameters
Crop Characteristics
Management and Environmental aspects are
factors affecting ET
88. Weather Parameters:
The principal weather conditions affecting
Evapotranspiration are:
Radiation
Air temperature
Humidity and
Wind speed.
89. Crop characteristics that affect ET :
Crop Type
Variety of Crop
Development Stage
Crop Height
Crop Roughness
Ground Cover
Crop Rooting Depth
90. Management and Environmental Factors :
Factors such as soil salinity,
Poor land fertility,
Limited application of fertilizers,
Absence of control of diseases and
Pests and poor soil management
May limit the crop development and
reduce soil Evapotranspiration.
91. Determination of ET
Evapotranspiration is not easy to measure.
Specific devices and accurate measurements of
various physical parameters or the soil water
balance in lysimeters are required to determine
ET.
The methods are expensive, demanding and
used for research purposes.
They remain important for evaluating ET
estimates obtained by more indirect methods.
92. Water Balance Method
The Water Balance or Budget Method is a
measurement of continuity of flow of water.
This method consists of drawing up a balance sheet of
all the water entering and leaving a particular
catchment or drainage basin.
The water balance equation can be written as:
ET = I + P – RO – DP + CR + SF + SW
Where: I is Irrigation, P is rainfall, RO is surface
runoff, DP is deep percolation, CR is capillary
rise, SF and SW are change in sub-surface flow and
change in soil water content respectively
93. Lysimeter Method
A water tight tank of cylindrical shape having dia about
2 m and depth about 3 m is placed vertically in
ground.
The tank is filled with sample soil.
Bottom of the tank consists of sand layer and a pan for
collecting surplus water.
The consumptive use of water is measured by the
amount of water required for the satisfactory growth of
plants with in tank.
Cu = Wa - Wd (Cu = consumptive use, Wa = water
applied, Wd = Water drained off)
94.
95. Field experimental method
Some fields are selected for expt.
The quantity of water is applied in such a way
that it is sufficient for satisfactory growth of
crops.
There should be no percolation or deep runoff.
If there is any runoff it should be measured and
deducted from the total quantity of water
applied.
96. Soil moisture study
Several plots of land are selected where irrigation
water is to be supplied.
The soil samples are taken from diff depths at the root
zone of the plants before and after irrigation.
Then water contents of the soil samples are
determined by laboratory tests.
The depth of water removed from soil determined by
Dr = pwd/ 100
(Dr= depth of water removed in m, p = % of water
content, w = sp. Gr. Of soil, d= depth of soil in m)
97. The total quantity of water removed in 30 days
period is calculated.
Then a curve of water consumption versus time
is prepared.
From this curve the water consumption for any
period can be calculated.
98. Penman Monteith method
• Penman–Monteith equation predicts
net Evapotranspiration, requiring as input
daily mean temperature, wind
speed, relative humidity, and solar
radiation.
99. • λv = Latent heat of vaporization. Energy
required per unit mass of water vaporized.
• Lv = Volumetric latent heat of vaporization.
Energy required per water volume
vaporized. (Lv = 2453 MJ m-3)
• E = Mass water Evapotranspiration rate (g
s-1 m-2)
• ETo = Water volume evapotranspired
(m3 s-1 m-2)
• Δ = Rate of change of saturation specific
humidity with air temperature. (Pa K-1)
100. • Often resistances are used rather than
conductivities.
• where rc refers to the resistance to flux
from a vegetation canopy to the extent of
some defined boundary layer.
101. • Rn = Net irradiance (W m-2), the external
source of energy flux
• cp = Specific heat capacity of air (J kg-1 K-
1)
• ρa = dry air density (kg m-3)
• δe = vapour pressure deficit, or specific
humidity (Pa)
• ga = Conductivity of air, atmospheric
conductance (m s-1)
• gs = Conductivity of stoma, surface
conductance (m s-1)
-1
102. Infiltration
• is the process by which water on the
ground surface enters the soil.
• Infiltration rate in soil science is a measure
of the rate at which soil is able to
absorb rainfall or irrigation. It is measured
in inches per hour or millimetres per hour.
The rate decreases as the soil becomes
saturated. If the precipitation rate exceeds
the infiltration rate, runoff will usually occur
unless there is some physical barrier.
103. • The rate of infiltration can be measured
using an infiltrometer.
104. Factors Affecting Infiltration
• Slope of the Land • Sorting
• Degree of
• Shape
Saturation
• Porosity • Capillarity
• Permeability • Vegetation
• Packing • Land Use
105. Infiltration indices
• The two commonly used infiltration indices
are the following:
ϕ – index
W – index
106. ϕ – index (Phi - index)
• This is defined as the rate of infiltration
above which the rainfall volume equals
runoff volume
107. • ϕ – index = precipitation – surface runoff
• ϕ – index = P – Q
• The value of ϕ – index can be derived
from the rainfall hyetograph and the
resulting surface runoff volume.
• ϕ – index can be determined for each
storm for which the surface runoff volume
has been measured.
• ϕ – index = (total infiltration during period
of rainfall excess) / period of rainfall
excess
108. W – index
• Is the average rate of infiltration during the
time when the rainfall intensity exceeds
the infiltration rate.
W – index = (P-Q-S)/tr
P = total precipitation (cm)
Q = total surface runoff (cm)
S = depression and interception losses (cm)
tr = duration of rainfall (hr)
109. • W – index is more accurate than ϕ – index
because it excludes the interception and
depression losses which are considered
as a part of infiltration.
• W – index is always less than ϕ – index.
• Because it is difficult to estimate
depression and interception losses.
• W – index not generally used in practice.
110. • W min – index
• Minimum rate of infiltration when a uniform
stage after stabilization is attained.
• W min index = ϕ – index after it is stabilized
= Kϕ – index, where K is
always less than 1.
111. Measurement of infiltration
• Infiltration capacity of soil can be
measured in field by conducting controlled
expt. using infiltrometers.
• Two types of infiltrometers are commonly
used
1. Flooding type
2. Rainfall simulator type
112. Flooding type infiltrometer
Simple infiltrometer
• metal cylinder of 25 to 30 cm dia and 50 to
60 cm length, open at both ends.
• Cylinder hammer in ground and 10 cm
length projects above the ground.
113. • top surface of soil inside ring is protected
by placing a perforated by placing a
perforated metallic dish over it.
• water poured into top part of a depth 5 cm
and pointer is set to mark.
• As infiltration takes place, water level goes
down.
• water maintained by adding water.
• readings are taken at regular time interval
to determine the rate and amount of
infiltration.
114. Rainfall simulator
• Water is applied in form of spray.
• Plate of 4m 2m selected, water applied
in form of artificial rain at uniform rate.
• Two rows of nozzles are installed to
produce rain drops.
• Various intensities of rainfall can be
simulated by changing nozzles opening.
• Expt. Conducted under controlled
conditions with various combinations of
intensities, durations and surface runoff.
115. Infiltration = Rainfall – surface runoff
• All terms expressed as depth of water over
the plot or as the volume of water.
• Infiltration determined from total infiltration
depth and duration of expt.
116. Horton’s equation
• Named after the same Robert E. Horton.
• Horton's equation is another viable option
when measuring ground infiltration rates or
volumes.
• It is an empirical formula that says that
infiltration starts at a constant rate, f0, and
is decreasing exponentially with time, t.
• After some time when the soil saturation
level reaches a certain value, the rate of
infiltration will level off to the rate fc.
117. ft = is the infiltration rate at time t;
f0 = is the initial infiltration rate or maximum
infiltration rate;
fc = is the constant or equilibrium infiltration
rate after the soil has been saturated or
minimum infiltration rate;
k= is the decay constant specific to the soil.
118. Green Ampt method
• Named for two men; Green and Ampt.
• It is a function of the soil suction
head, porosity, hydraulic conductivity and
time.
• Where
• Ψ = is wetting front soil suction head;
• θ = is water content;
• K= is Hydraulic conductivity;
• F= is the total volume already infiltrated.
119. • Once integrated, one can easily choose to
solve for either volume of infiltration or
instantaneous infiltration rate:
•
• Using this model one can find the volume
easily by solving for F(t).
120. • However the variable being solved for is in
the equation itself so when solving for this
one must set the variable in question to
converge on zero, or another appropriate
constant.
• The only note on using this formula is that
one must assume that , the water head or
the depth of ponded water above the
surface, is negligible.
121. • Using the infiltration volume from this
equation one may then substitute F into
the corresponding infiltration rate equation
below to find the instantaneous infiltration
rate at the time, t, F was measured.