Investigation of Crack Width Development in Reinforced Concrete Beams Using F...
Comminution
1. SUMMARY
This review looks at the basic concepts of comminution, including principles and
different theories of comminution. It also tells the recent trends in the
comminution industry and provides links to different simulation packages
available, university and research centers and important books and other
references.
INTRODUCTION
Most of the minerals are finely disseminated and intimately associated with the
gangue so; they must be initially liberated before separation can be done.
Comminution is the process in which the particle size of the ore is progressively
reduced until the clean particles of mineral can be separated by such methods
as are available. Comminution in its earliest stages can also be carried out in
order to make the freshly excavated material easier to handle by scrapers,
conveyors, and ore carriers, and in the case of quarry products to produce
material of controlled particle size.
Blasting can be described as the first stage of comminution carried out in the
mine site in order to remove ores from their natural beds. Comminution in the
mineral processing plant takes place in a sequence of crushing and grinding
processes. Crushing reduces the particle size of run-of-mine ore to such a level
that grinding mill can further grind it until the mineral and gangue is substantially
produced as separate particles.
Crushing is accomplished by compression of the ore against rigid surfaces, or
by impact against surfaces in a constrained motion path. Grinding is
accomplished by abrasion and impact of the ore by the free motion of
unconnected media such as rods, balls, or pebbles.
Crushing is usually a dry process, and is performed in several stages, reduction
ratios being small, ranging from three to six in each stage. The reduction ratio of
a crushing stage can be defined as the ratio of maximum particle size entering
to maximum particle size leaving the crusher, although other definitions are
sometimes used. There are a number of crushers available as jaw, gyratory,
cone, roll, and impact crushers.
Grinding is usually performed wet to provide a slurry feed to the concentration
process, although dry grinding has limited applications. There is an overlapping
size area where it is possible to crush or grind the ore. From a number of case
studies, it appears that at the fine end of crushing operations equivalent
reduction can be achieved for roughly half the energy and costs required by
grinding mills (Flavel, 1978).
Tumbling mills for size reduction with either steel rods (rod mills) or balls (ball
mills), or sized ore (AG & SAG mills) as the grinding media used depending
upon the size and energy considerations.
2. Stirred mills represent the broad category of mills, which use a stirrer to provide
motion to the steel, ceramic, or rock media. Both vertical and horizontal
configurations exist, and since they can operate with smaller media sizes, they
are far more suitable for fine grinding applications than ball mills. Stirred mills
are claimed to be more energy efficient (by up to 50%) than conventional ball
mills (Stief et al., 1987).
Principles of Comminution
The increase in stress at a site is proportional to the square root of the crack
length perpendicular to the stress direction (Inglis, 1913). Therefore, there is a
critical value for the crack length at any particular level of stress at which the
increased stress level at the crack tip is sufficient to break the atomic bond at
that point. Such rupture of the bond will increase the crack length, thus
increasing the stress concentration and causing a rapid propagation of the
crack through the matrix, thus causing fracture. When fracture does occur,
some of the stored energy is transformed into free surface energy, which is the
potential energy of atoms at the newly produced surfaces.
Mainly breakage achieved by crushing, impact, and attrition, and all three
modes of fracture (compressive a, tensile b, and shear c) can be discerned
depending on the rock mechanics and the type of loading.
When an irregular particle is broken by compression, or crushing, the products
fall into two distinct size ranges coarse particles resulting from the induced
tensile failure, and fines from compressive failure near the points of loading, or
by shear at projections. Minimizing the area of loading can reduce the amount
of fines produced and this is often done in compressive crushing machines by
using corrugated crushing surfaces (Partridge, 1978). In impact breaking, due to
the rapid loading, a particle experiences a higher average stress while
undergoing strain than is necessary to achieve simple fracture, and tends to
break apart rapidly, mainly by tensile failure. The products are often very similar
in size and shape. Attrition (shear failure) produces much fine material, and may
be undesirable depending on the comminution stage and industry sector.
Attrition occurs mainly in practice due to particle- particle interaction (inter-
particle comminution), which may occur if a crusher is fed too fast, contacting
particles thus increasing the degree of compressive stress and hence shear
failure.
3. Theory of Comminution
Comminution theory is concerned with the relationship between energy input
and the particle size made from a given feed size. The greatest problem is that
the machine itself absorbs most of the energy input to a crushing or grinding
machine, and only a small fraction of the total energy is available for breaking
the material. It is to be expected that there is a relationship between the energy
required breaking the material and the new surface produced in the process,
but this relationship can only be explained if the energy consumed in creating
new surface can be separately measured. Another factor is that a material,
which is plastic, will consume energy in changing shape, a shape that it will
retain without creating significant new surface. All the theories of comminution
assume that the material is brittle, so that no energy is adsorbed in processes
such as elongation or contraction, which is not finally utilized in breakage.
The oldest theory is that of Von Rittinger (1867), which states that the energy
consumed in the size reduction is proportional to the area of new surface
produced.
Where E is the energy input, D1 is the initial particle size, D2 is the final particle
size, and K is a constant.
Kick (1885) stated that the work required is proportional to the reduction in
volume of the particles concerned. Where f is the diameter of the feed particles
and p the diameter of the product particles, the reduction ratio R is f/p.
According to Kick's law, the energy required for comminution is proportional to
log R/log 2.
Bond (1952) developed an equation which is based on the theory that the work
input is proportional to the new crack tip length produced in particle breakage,
and equals the work represented by the product minus that represented by the
feed. In particles of similar shape, the surface area of unit volume of material is
inversely proportional to the diameter. The crack length in unit volume is
considered to be proportional to one side of that area and therefore inversely
proportional to the square root of the diameter.
For practical calculations the size in microns which 80% passes is selected as
the criterion of particle size. The diameter in microns which 80% of the product
passes is designated as P, the size which 80% of the feed passes is designated
as F, and the work input in kilowatt hours per short ton is W. Bond's third theory
equation is
4. Where Wi is the work index. The work index is the
comminution parameter, which expresses the
resistance of the material to crushing and grinding;
numerically it is the kilowatt-hours per short ton required to reduce the material
from theoretically infinite feed size to 80% passing 100 microns.
Hukki (1975) suggests that the relationship between energy and particle size is
a composite form of the three laws. The probability of breakage in comminution
is high for large particles, and rapidly diminishes for fine sizes. On the basis of
Hukki's evaluation, Morrell (2004) has proposed a modification to Bond's
where Mi is the material index related to the breakage
property of the ore and K is a constant chosen to
balance the units of the equation. The application of
the new energy-size relation has been shown to be valid across the size range
covered by most modern grinding circuits, i.e. 0.1-100 mm.
Grindability
Ore grindability refers to the ease with which materials can be comminuted, and
data from grindability tests are used to evaluate crushing and grinding
efficiency. Most widely used parameter to measure ore grindability is the Bond
work index Wi that is described in previous paragraph. Berry and Bruce (1966)
developed a comparative method of determining the grindability of an ore. The
method requires the use of a reference ore of known grindability. The reference
ore is ground for certain time and the power consumption recorded. An identical
weight of the test ore is then ground for a length of time such that the power
consumed is identical with that of the reference ore. If r is the reference ore and
t the ore under test, then from Bond's Equation,
While Bond is the best-known grindability test for rod and ball mills, in recent
years the SPI (SAG Power Index) test has become popular for SAG mills. The
SPI test is a batch test, conducted in a 30.5 cm diameter by 10.2 cm long
grinding mill charged with 5kg of steel balls. Two kilograms of sample are
crushed to 100% minus 1.9 cm and 80% minus 1.3 cm and placed in the mill.
The test is run with several screening iterations until the sample is reduced to
80% minus 1.7 mm. The time required to reach a P80 of 1.7 mm is then
converted to an SAG power index Wsag via the use of a proprietary
transformation (Starkey and Dobby, 1996):
The parameters K and n are empirical factors whilst
fsag incorporates a series of calculations
(unpublished), which estimate the influence of factors
such as pebble crusher recycle load, ball load, and
5. feed size distribution. The test is essentially an indicator of an ore's breakage
response to SAG abrasion events.
Recent Developments in Comminution
A relatively new comminution device, the high pressure grinding rolls (HPGR)
adapted in cement industry and got application in diamond crushing, utilizes
compression breakage of a particle bed, in which energy efficient inter-particle
breakage occurs (Schrnert, 1988). The reduction ratio obtained in a single pass
through the HPGR is substantially higher than that obtained in conventional rolls
crushers. Some evidence has also been reported for downstream benefits such
as reduced grinding strength and improved leachability due to micro-cracking
(Knecht, 1994). The HPGR offers a realistic potential to markedly reduce the
comminution energy requirements needed by tumbling mills. Reports have
suggested the HPGR to be between 20 and 50% more efficient than
conventional crushers and mills (Esna-Ashari and Kellerwessel, 1988).
In addition of HPGR, some other mills are also developed such as Poittemill,
HPROMILL, Sala Agitated mill (SAM), IsaMill, ANI-Metprotech Stirred Vertical
mill, ALPINE ATR Mill, MaxxMill, KD Tower Mill, Vibration mills such as
Eccentric vibrating mill (ESM), VibroKinetic Energy (VKE) Mill, Centrifugal mills
such as ZRM centrifugal tube mill, Aachen centrifugal mill, Jet mills, Hicom mills
etc. (Wang and Eric, 2003)
Wang and Forssberg (2001) summarized the product size-specific energy input
relations obtained by various recently developed mills such as MaxxMill�,
Drais mill, ESM, SAM and HPRM as well in the comminution of limestone.
Clearly, these new or developed mills have shown a superior performance for
size reduction and energy saving compared to the conventional ball mill.
Modeling and Simulation Software
JKSimMet is a general-purpose computer software package for the analysis of
comminution and classification circuits in mineral processing operations.
JKSimMet integrates all tasks associated with data analysis, optimization,
design and simulation, including the storage and manipulation of models, data
and results, within one package. Mass balancing and model fitting of complete
circuits are standard features. It is fully interactive and operates with high-
resolution color graphics. These graphics facilitate the display of detailed plant
flowsheets and accompanying information.
Metso Minerals Co. has developed a crushing plant simulator named BRUNO.
This simulator has been utilized to facilitate the comminution equipment
selection process. The program was a DOS based mass balance program that
kept track of the tonnage rate of each size fraction in various circuit flows.
Sandvik Rock Processing AB, Sweden introduced a simulator PlantDesigner�
for optimization and design of crushing and screening plant circuits. This
PlantDesigner� software is a PC program in Windows 98/ME or Windows
2000/XP for design of flowsheets, simulation of processes and calculation of
6. mass balances for crushing and screening plants. The programming language
is a structured subset of C with object-oriented extensions.
The USIM PAC simulator for design/optimization of mineral processing plant
has been developed for 16 years by BRGM, France. The latest version
available is the USIM PAC 3.0, which incorporates the modern developments.
This is a user-friendly steady-state simulator that allows processing engineers
and researchers to model plant operations with available experimental data and
determine optimal plant configuration that meets production targets.
The University of Utah, USA has developed a simulator MODSIM. The
simulator offers the versatility to the user to modify and adapt the models of the
unit operations that are used. The underlying theme for the models that are
used in the MODSIM is the population balance method. In addition to the
application in engineering, the MODSIM has been used as an academic tool to
enhance the educational experience of students of mineral processing.
DEM Solutions software is used to simulate, analyze, and visualize particle
flows so that you can get a feel for what is happening in a situation involving
particle kinematics, momentum, and heat and mass transfer.
The Australian CSIRO reports on the use of the Discrete Element Method to
research the functioning of mills. They have used a discrete element method to
simulate the charge motion in a centrifugal mill with various loadings.
SGS Group software CEET® is an internet-based software tool that enables
accurate design and forecasting of plant throughputs, operating costs and grind
quality. Capital investment and production planning decisions can thus be
based on well-defined representative data sets representing the resource
model.
Books & Magazines
The most important book for understanding the basic of the comminution is Mineral Processing Technology by B. A.
Wills. The Other important book will be Advances in Comminution by S. K. Kawatra.
In addition of this different conferences on comminution, crushing and milling publish their proceedings that is the most
useful source for getting the recent developments in this field. The proceedings includes:
IMPC proceedings
SAG conference
Comminution conference