1. For more information, contact:
Bob Bevill, bob@bevill.com,
+1 (888) NO-BUSY1
IM: MerrimackBob
Remote Access Server (RAS) Information
Burbank Telephone Configuration
12 Standard POTS lines, muxed through a Channel Bank Server.
Carrier Access Corporation – Access Bank I
DIP Switch settings --- I (on) O (off)
1234567890
OOIOOOOO
T-1 Settings
Clock Source – Local
T1 Framing – D4
T1 Line Coding – AMI
T1 Signaling – Loop-Start
Connection from Channel Bank to Max 6000
Requires a T-1 “crossover” cable, in order to properly communicate.
Pin-out Configuration is as follows:
1 5
2 4
4 2
5 1
Connection from:
Channel Bank to MOD-TAP Patch Panel Cable (straight through)
MOD-TAP (telephone closet) to MOD-TAP (computer lab)
Patch Panel Cable (straight through)
MOD-TAP to Max 6000 T-1 “crossover” cable
2. Remote Access Server (RAS) Information Page 2
Burbank – Max 6000 Configuration
To connect to the Burbank Max 6000, telnet to 192.168.242.11, port 7011.
00-000 System
00-100 Sys Config
Name BVDCTEST
Location Burbank
Contact Victor Ho 818-855-4795
10-000 Net/T1
10-100 Line Config
10-1**
1st
Line=Trunk
2nd
Line=Disabled
Line 1…
Sig Mode Inband
Rob Ctl Loop-Start
Framing Mode D4
Encoding AMI
Clock Source Yes
Ch 1 Switched
Ch 1 # 842-8269
Ch 1 Slot 4
Ch 1 Prt/Grp 0
Ch 2 Switched
Ch 2 # 842-8284
Ch 2 Slot 4
Ch 2 Prt/Grp 0
Ch 3 Switched
Ch 3 # 842-8296
Ch 3 Slot 4
Ch 3 Prt/Grp 0
Ch 4 Switched
Ch 4 # 842-8298
Ch 4 Slot 4
Ch 4 Prt/Grp 0
Ch 5 Switched
Ch 5 # 842-8378
Ch 5 Slot 4
Ch 5 Prt/Grp 0
Ch 6 Switched
Ch 6 # 842-8527
Ch 6 Slot 4
Ch 6 Prt/Grp 0
Ch 7 Switched
4. Remote Access Server (RAS) Information Page 4
Pool #1 Count 12
DHCP Client No
DHCP Spoof
DHCP Spoofing No
DNS
Pri DNS 192.168.245.10
Sec DNS 0.0.0.0
Allow as Client DNS Yes
Pri WINS 0.0.0.0
Sec WINS 0.0.0.0
Client Pri DNS 192.168.245.10
Client Sec DNS 0.0.0.0
Auth
Auth RADIUS
Auth Host #1 192.168.242.23
Auth Host #2 0.0.0.0
Auth Host #3 0.0.0.0
Auth Port 1812
RADIUS Server
Server Yes
Client #1 192.168.245.151/24
Client Key#1 maxtest
Modem Ringback No
Burbank – Radius Server
Presently configured as Open Source Cistron Radius v.1.6.6
Modifications from default “make/make install”:
• Added Burbank Max 6000 to /etc/raddb/clients file
(i.e. “192.168.245.151<tab><tab>maxtest”)
• Requires startup of radiusd daemon in /etc/rc.local -- no add-on parameters
required
Cincinnati Telephone Configuration
Four PRI T-1’s12, using standard B8ZS/ESF/NI-2
The PRI’s are using a single D-channel as primary controller – no secondary needed.
T-1 Settings
Clock Source – Local
T1 Framing – ESF
T1 Line Coding – B8ZS
5. Remote Access Server (RAS) Information Page 5
T1 Signaling – N/A (since there is no PBX to connect with)
Cincinnati – Max 6000 Configuration
To connect to the Cincinnati Max 6000, telnet to 172.20.252.85, port 7008.
00-000 System
00-100 Sys Config
Name BVDC
Location Convergys
Contact Victor Ho 818-855-4795
10-000 Net/T1
10-100 Line Config
10-1**
1st
Line=Trunk
2nd
Line=Trunk
Line 1…
Sig Mode ISDN_NFAS
NFAS ID num0
Rob Ctl N/A
Switch Type NI-2
Framing Mode ESF
Encoding B8ZS
Clock Source Yes
Ch 1 -23 Switched
Ch 24 NFAS-PRIME
Line 2…
Sig Mode ISDN_NFAS
NFAS ID num1
Rob Ctl N/A
Switch Type NI-2
Framing Mode ESF
Encoding B8ZS
Clock Source Yes
Ch 1 -23 Switched
Ch 24 NFAS-SECOND
20-000 Net/T1
20-100 Line Config
20-1**
1st
Line=Trunk
6. Remote Access Server (RAS) Information Page 6
2nd
Line=Trunk
Line 1…
Sig Mode ISDN_NFAS
NFAS ID num2
Rob Ctl N/A
Switch Type NI-2
Framing Mode ESF
Encoding B8ZS
Clock Source Yes
Ch 1 -23 Switched
Ch 24 NFAS-PRIME
Line 2…
Sig Mode ISDN_NFAS
NFAS ID num3
Rob Ctl N/A
Switch Type NI-2
Framing Mode ESF
Encoding B8ZS
Clock Source Yes
Ch 1 -23 Switched
Ch 24 NFAS-SECOND
90-000 Ethernet
90-700 Answer
User Answer as Default Yes
Force 56 Yes
Profile Reqd Yes
Id Auth Ignore
Assign Adrs Yes
PPP Options
Route IP Yes
Recv Auth PAP
Link-comp Stac-9
CJ-Comp Yes
Session Options
RIP Off
Idle 600
90-G00 Mod config
Ether Options
IP Adrs 172.20.253.1/25
WAN Options
Pool #1 Start 172.20.253.2
Pool #1 Count 92
DHCP Client No
7. Remote Access Server (RAS) Information Page 7
DHCP Spoof
DHCP Spoofing No
DNS
Pri DNS 192.168.245.10
Sec DNS 0.0.0.0
Allow as Client DNS Yes
Pri WINS 0.0.0.0
Sec WINS 0.0.0.0
Client Pri DNS 192.168.245.10
Client Sec DNS 0.0.0.0
Auth
Auth RADIUS
Auth Host #1 172.20.252.36
Auth Host #2 0.0.0.0
Auth Host #3 0.0.0.0
Auth Port 1812
RADIUS Server
Server Yes
Client #1 172.20.252.36/24
Client Key#1 maxmp1
Modem Ringback No
Cincinnati – Radius Server
Presently configured as Open Source Cistron Radius v.1.6.6
Modifications from default “make/make install”:
• Added Cincinnati Max 6000 to /etc/raddb/clients file
(i.e. “172.20.252.36<tab><tab>maxmp1”)
• Requires startup of radiusd daemon in /etc/rc.local -- no add-on parameters
required