How To Install Silver Vapor 3-in-1 Flooring Underlayment
•Transferir como PPTX, PDF•
4 gostaram•233,180 visualizações
This illustrated guide will show you with detailed step-by-step pictures how to install Silver Vapor 3-in-1 Flooring Underlayment. (Available here: http://ow.ly/yCiNz)
Recomendados
Mais conteúdo relacionado
Mais procurados
Mais procurados (15)
Semelhante a How To Install Silver Vapor 3-in-1 Flooring Underlayment
Semelhante a How To Install Silver Vapor 3-in-1 Flooring Underlayment (20)
Último
Último (20)
How To Install Silver Vapor 3-in-1 Flooring Underlayment
- 1. How To Install Silver Vapor 3-in-1 Flooring Underlayment
- 2. Make it a DIY Project and save on your floor installation cost
- 3. Fact: Laying down underlayment is 10% of your installation cost
- 4. You may need: Enough vapor 3-in-1, Flooring, broom & dust pan, tape, scissors/utility knife
- 5. Step 1: Get cleaning! Subfloor should be clean and free of dirt.
- 6. Step 2: Subfloor check – subfloor should be in good condition without damages
- 7. Step 3: Fix Subfloor – subfloor needs fixing if: It is sloping, has excessive gabs, cracks or any areas with moisture.
- 8. Step 4: Time to get started – roll out vapor underlayment with the silver side facing down.
- 9. Quick hint: Overlapping film should be towards open room & Tape strip next to wall
- 10. Step 5: Install Parallel to the wall
- 11. Step 6: Cut your measured section with a utility knife
- 12. Step 7: You may add tape to temporally hold underlayment in place
- 13. Step 8: Install flooring on the underlayment section already installed
- 14. Cross stack your flooring – make sure to acclimate your flooring at least 48 hours before the installation
- 15. Step 9: Start your new roll – repeat step 4 and start your next roll
- 16. Step 10: Measure and Pre-cut next section
- 17. Step 11: Combine edges - butt edges together making sure to overlap only the silver film
- 18. Step 12: Remove adhesive layer and stick to underlament
- 19. Step 13: Use additional tape to secure rows if needed
- 20. Step 14: Continue Installation according to manufacturers instructions
- 21. Connect with us : www.bestlaminate.com / Facebook.com/Bestlaminate / Twitter.com/Bestlaminate www.Bestlaminate.com Facebook.com/Bestlaminate Twitter.com/Bestlaminate
Notas do Editor
- How To Install Silver Vapor 3-in-1 Flooring Underlayment
- Make it a DIY Project and save on your floor installation cost
- Fact: Laying down underlayment is 10% of your installation cost
- You may need: Enough vapor 3-in-1, Flooring, broom & dust pan, tape, scissors/utility knife
- Step 1: Get cleaning! Subfloor should be clean and free of dirt.
- Step 2: Subfloor check – subfloor should be in good condition without damages
- Step 3: Fix Subfloor – subfloor needs fixing if: It is sloping, has excessive gabs, cracks or any areas with moisture.
- Step 4: Time to get started – roll out vapor underlayment with the silver side facing down.
- Quick hint: Overlapping film should be towards open room & Tape strip next to wall
- Step 5: Install Parallel to the wall
- Step 6: Cut your measured section with a utility knife
- Step 7: You may add tape to temporally hold underlayment in place
- Step 8: Install flooring on the underlayment section already installed
- Cross stack your flooring – make sure to acclimate your flooring at least 48 hours before the installation
- Step 9: Start your new roll – repeat step 4 and start your next roll
- Step 10: Measure and Pre-cut next section
- Step 11: Combine edges - butt edges together making sure to overlap only the silver film
- Step 12: Remove adhesive layer and stick to underlament
- Step 13: Use additional tape to secure rows if needed
- Step 14: Continue Installation according to manufacturers instructions
- Connect with us : www.bestlaminate.com / Facebook.com/Bestlaminate / Twitter.com/Bestlaminate